Knightsbridge SL9LED Single Voltage LED Shaver Light Instruction Manual

: June 12, 2024
: Knightsbridge

Table of Contents

GENERAL INSTRUCTIONS
SAFETY
INSTALLATION
GENERAL
WARRANTY
Documents / Resources

SL9LED Single Voltage LED Shaver Light Instruction Manual

GENERAL INSTRUCTIONS

These instructions should be read carefully and retained after installation by the end user for future reference and maintenance. These instructions should be used to aid installation of the following product: SL9LED

SAFETY

This product must be installed in accordance with the Latest edition of the LEE Wiring Regulations (357671) and current Building Regulations. If in any doubt. consult a qualified electrician
Please isolate mains prior to installation or maintenance
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the circuit cable. fuse or circuit breaker
Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for installation
This product is Class II double insulated
This product series is IP44 rated

INSTALLATION

Note – If this luminaire is being used in conjunction with an external PIR or sensor. please confirm with the manufacturer of the sensors that they are compatible with LED luminaires

Provide power to the required point of installation
Using the brackets as templates. mark the location for. and drill the fixing holes ensuring not to infringe with any gas / water pipes or electrical cables (see Fig. 1)
Note. There is a maximum distance of 300mm between the two mounting brackets
To prevent the fitting moving from left to right there is a fixing hole at either end under the end caps. Slide the end caps off then, using the fitting as a template mark the location for, and drill the fixing holes ensuring not to infringe with any gas / water pipes or electrical cables (see Fig. 2) Fig. 2
Mount the brackets to the wall using the screws provided
Open the junction box on the rear of the luminaire and feed the mains cable through the rubber grommet to retain IP rating
Ensuring correct polarity is observed. carefully wire as shown in Fig.
Close the junction box lid
Align the luminaire and attach to the top edge of the brackets then push down to clamp onto the bottom edge of the brackets as shown in Fig. 4.
Screw the fitting to the wall under the end caps. then slide the end caps into place
Switch on and check for correct operation
Note — The pullcord is for light operation only. Shaver and USB Charger remain permanently live

WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

This product contains a light source of energy efficiency class No Regulation (al) No. 2019/2015 and (UK) 2025 No. 1095. This product contains a nonreplaceable LED light source and a control gear which can be replaced by a professional. Knightsbridge SL9LED Single Voltage LED Shaver Light - Fig
3 Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only. do not use aggressive cleaning products or solvents which may damage the product. This product is non-dimmable. This product should be dismantled for disposal when it reaches the end of its life. Please see website for dismantling instructions. This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities for where facilities exist

WARRANTY

This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance with the current edition of the IEE Wiring Regulations (1E67671). improper use. or removal of the batch code will invalidate the warranty. If this product should fail within its warranty period. it should be returned to the place of purchase for a free of charge replacement ML Accessories does not accept responsibility for any installation costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve the right to alter product specification without prior notice..

Supplied By:
(UK) Manufacturer ML Accessories Ltd, Unit E Chiitem Park, Boscombe Road, Dunstable LU5 4LT,
www.mtaccessories.co.uk
(EU) Authorised Representative nnuks Holding GmbH, Niederkasseler Lohweg 18,
40547 Dusseldorf, Germany, Email: eprel@nnuks.com
Knightsbridge SL9LED Single Voltage LED Shaver Light - Fig
4

Documents / Resources

| Knightsbridge SL9LED Single Voltage LED Shaver Light [pdf] Instruction Manual
SL9LED, SL9LED Single Voltage LED Shaver Light, Single Voltage LED Shaver Light, Voltage LED Shaver Light, LED Shaver Light, Shaver Light, Light
---|---
| Knightsbridge SL9LED Single Voltage LED Shaver Light [pdf] Instruction Manual
SL9LED Single Voltage LED Shaver Light, SL9LED, Single Voltage LED Shaver Light, Voltage LED Shaver Light, LED Shaver Light, Shaver Light, Light