BIXOLON SRP-B300 Thermal Receipt Printer Installation Guide

: June 12, 2024
: BIXOLON

Table of Contents

◈ Information
◈ Components
◈ Cable Connection
◈ Using Control Panel
◈ Self-Test
◈ Safety Precautions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Printer Installation Guide & Safety Guide
KN04-00204A (Ver.1.2)
THERMAL RECEIPT PRINTER SRP-B300

◈ Information

This installation guide contains only simple information required for the installation of the product. Detailed information of the installation can be found on the “Download” tab of BIXOLON website (www.bixolon.com) and, it includes the following contents.

Manual: User’s Manual, Code Page Manual, Command Manual, Network Manual, Software Manuals
Driver: Windows Driver, OPOS Driver, JPOS Driver, CUPS (Linux, Mac) Driver, Virtual Port Driver
SDK: Windows POS SDK, iOS SDK, Android SDK, Xamarin SDK

We at Bixolon Co., Ltd. constantly strive to improve product functions and quality.
To do this, the specifications of our product and the contents of the manual may change without prior notice.
Please refer to the BIXOLON website for the addresses and phone numbers of the company’s headquarters and branch offices. (http://www.bixolon.com)

◈ Components

Product
Standard Components
Optional Components Serial Cabel (9pin – 9pin)

◈ Cable Connection

Turn off the printer and POS System (host computer).
Connect the power cord to adaptor and connect the adapter to the power connector of the printer.
Check the type interface located at the back of the printer and connect proper cable.
Please plug the cash drawer cable in the DK port at the rear side of the printer.

※ Do not use an adapter that was not supplied with the printer.
– SRP-B300ES BIXOLON SRP B300 Thermal Receipt Printer - Cable
Connection

◈ Installing Paper Roll BIXOLON SRP B300 Thermal Receipt Printer - Paper
Roll

Open the paper roll cover by pull the Cover-Open Lever.
Insert new roll paper in the correct direction.
Pull the paper out slightly and close the cover.

※ Note
Hold down the center of the cover firmly when closing the cover so that the paper maintains close contact with the roller. Printing quality may not be optimum if ecommended paper is not used.

◈ Paper Jam
(Refer to 1-8 in User’s Manual)

Turn the printer off and on, open the cover, and remove the paper.
If cover does not open, please contact Customer Service.

◈ Using Control Panel

Power LED (Indicator Lamp)
The Power light is on whenever the printer is on.
Error (Indicator Lamp)
Red light will be on in various error conditions such as out of paper, cover open, etc.
Feed (Button)
Press this button to feed the paper out.
Hold down this button to feed out the paper continuously.

◈ Self-Test

Check whether paper is mounted correctly.
Turn on the power while holding down the Feed button and the self-test procedure will begin.
Printer will print out the current status of printer including the version of ROM.
After printing out the current status of printer, the printer will print following lines and waits for the next step (paper lamp will keep blinking).
SELF-TEST PRINTING.
SELECT MODES BY PRESSING FEED BUTTON.
Continuous test printing: Less than 1 second
VMSM Selection: 1 second or more
Press the Feed button to resume printing or hold down the button for at least one second to change the VMSM settings.
5-1 If “Continuous SELF-TEST” is selected
5-1-1 Press the Feed button for less than one second to print the preset page.
5-1-2 The self test ends automatically as it prints the following line and cuts the paper.
COMPLETED
5-1-3 The printer goes into normal print mode upon completion of the self test.
5-2 If “VMSM Selection” is selected.
5-2-1 The following lines will be printed when the VMSM opens
VMSM Selection
0: Exit and reboot printer
1: Print current settings
2: Set Print Density
3: Set Cutting mode
4: Set External Buzzer after cutting
5 or more: None
5-2-2 Press the Feed button to run the above function.
5-2-2-1 Step 1(Select Options): press the button a number of times as shown by each menu.
5-2-2-2 Step 2(Enter Options): hold down the button for at least one second to apply each item selected.
※ Note
If you select any items not listed above, the list of “VMSM Selection” will be printed again. Setting the mode will be canceled if no item is selected in Step 1.
5-3 Hold down the Feed button for at least 1 second to save the changes.
The following line will be printed before cutting the paper.
COMPLETED
※ Attention
If “0: Exit and reboot printer” is not executed, the new settings will not be saved.
The new settings will be automatically applied when printer resets.

※ Note
You can check whether printer works correctly or not through the self-test.
Printing quality, ROM version, and memory switch settings can be checked through the self-test function.
◈ Reconfiguration of Printer
SRP-B300 does not support Dip Switch. To change the settings of the printer, use the virtual memory switch utility or virtual memory switch control function for self-diagnosis.

◈ WEEE(Waste Electrical and Electric Equipment)
**** This marking shown on the product or its literature, indicates that is should not be disposed of with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

◈ Safety Precautions

In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage.
WARNING
Violating following instructions can cause serious injury or death.

Do not plug several products in one multi-outlet.

This can provoke over-heating and a fire.
If the plug is wet or dirty, dry or wipe it before usage.
If the plug does not fit perfectly with the outlet, do not plug in.
Be sure to use only standardized multi-outlets.

You must use only the supplied adapter.

It is dangerous to use other adapters.

Do not pull the cable to unplug.

This can damage the cable, which is the origin of a fire or a breakdown of the printer.

Keep the plastic bag out of children’s reach.

If not, a child may put the bag on his head.

Do not plug in or unplug with your hands wet.

You can be electrocuted.

Do not bend the cable by force or leave it under any heavy object.

A damaged cable can cause a fire.

CAUTION
Violating following instructions can cause slight wound or damage the appliance.
If you observe a strange smoke, odor or noise from the printer, unplug it before taking following measures.