apollo SA4700-102APO Intelligent Input-Output Module Installation Guide
- June 12, 2024
- APOLLO
Table of Contents
**Intelligent Input/Output Unit
Installation Guide
**
| Part No | Product Name |
|---|---|
| SA4700-102APO | Intelligent Input/Output Unit |
Technical Information
All data is supplied subject to change without notice. Specications are typical at 24V, 25°C and 50% RH unless otherwise stated.
| Supply Voltage | 17-35V dc |
|---|---|
| Quiescent Current | 500µA |
| Power-up Surge Current | 900µA |
| Relay Output Contact Rating | 1A at 30V dc or ac |
| LED Current | 1.6mA per LED |
| Maximum Loop Current (Imax; L1 in/out) | 1A |
| Operating Temperature | 0°C to 70°C |
| Humidity | 0% to 95% RH (no condensation or icing) |
| Approvals | EN 54-17 & EN 54-18 |
For additional technical information please refer to the following documents
which are available on request.
PP2553 – Intelligent Input/Output Unit
Drill holes where required.
Do not over
tighten screws
Remove knockouts and
tglands where required.
Do not over tighten screws
The 8th
segment must be in set to ‘0’ for Discovery / XP95 operation
All CI tests must be carried
before connecting the interface. For connectivity instruction see Figs 1, 2 &
3
Note the alignment marks
Addressing
| XP9S / Discovery Systems| CoreProtocol Systems
---|---|---
Segment I| 1| Sets the address| Sets the address
2
3
4
5
6
7
8| Set to ‘0’ (Fault value is returned if set to ‘1’)
FS| Enables failsafe mode (compliant with 13S7273-4 for door holders)| Enables
failsafe mode (compliant with B57273-4 for door holders)
| LED| Enables/Disables LED (except Isolator LED)| Enables/Disables LED
(except Isolator LED)
Note : On mixed systems addresses 127 and 128 are reserved. Refer to system’s panel manufacturer for further information.
Address Setting Examples
|
---|---
Connectivity Examples
When operated under XP95 or Discovery Protocols, EN54-13
type 2 devices can be connected. In case EN54-13 type 1 devices need to be
connected they must be installed directly next to this module, with no
transmission path according to EN 54-13.
LED Status Indicator
| RLY | Continuous Red | Relay Active |
|---|---|---|
| Continuous Yellow | Fault |
POLL/
ISO| Flashing Green| Device Polled
Continuous Yellow| Isolator Active
IP| Continuous Red| Input Active
Continuous Yellow| Input Fault
Note : Not all LEDs can be on simultaneously.
Commissioning
The installation must conform to BS5839–1 (or applicable local codes).
Maintainence
Removal of the external cover must be carried out using a at screwdriver or
similar tool.
Caution
Unit damage. No electrical supply greater than 50V ac rms or 75V dc should be
connected to any terminal of this Input/Output Unit.
Note : For compliance with Electrical Safety Standards the sources
switched by the output relays must be limited to a 71V transient over-voltage
condition.
Contact Apollo for more information.
Troubleshooting
Before investigating individual units for faults, it is important to check that the system wiring is fault free. Earth faults on data loops or interface zone wiring may cause communication errors. Many fault conditions are the result of simple wiring errors. Check all connections to the unit.
| Problem | Possible Cause |
|---|---|
| No response or missing | Incorrect address setting Incorrect loop wiring |
Incorrect address setting
Incorrect loop wiring| Incorrect input wiring
Incorrect wiring
Control panel has incorrect cause
and effect programming
Relay energised continuously| Incorrect loop wiring
Incorrect address setting
Analogue value unstable| Dual address
Loop data fault, data corruption
Constant Alarm| Incorrect wiring
Incorrect end-of-line resistor tted
Incompatible control panel software
Isolator LED on| Short-circuit on loop wiring
Wiring reverse polarity
Too many devices between isolators
**Mode Table***
| Mode | Description |
|---|---|
| 1 | DIL Switch XP Mode |
| 2 | Alarm Delays |
| 3 | Output and N/O input (can be equivalent for Output only) |
| 4 | Output and N/C input |
| 5 | Output with Feedback (N/C) |
| 6 | Failsafe Output with Feedback (N/C) |
| 7 | Failsafe Output without Feedback |
| 8 | Momentary Input Activation Sets Output Relay |
| 9 | Input Activation Sets Output |
*CoreProtocol enabled systems only
© Apollo Fire Detectors Limited 20Apollo Fire
Detectors Limited, 36 Brookside Road, HPO9 1JR, UK
Tel: +44 (0) 23 9249 2412
Fax: +44 (0) 23 9
Email:techsalesemails@apollo-re.com
Website:
Documents / Resources
|
apollo SA4700-102APO Intelligent Input-Output
Module
[pdf] Installation Guide
SA4700-102APO Intelligent Input-Output Module, SA4700-102APO, Intelligent
Input-Output Module, Input-Output Module, Module
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>