UNILITE WCHT5 Wireless Charging Headtorch User Manual
- June 12, 2024
- Unilite
Table of Contents
WCHT5
FEATURES
- High power 550 lumen white COB LED, 6500k
- Additional 450 lumen 6500K Cree LED spot beam LED
- Super tough polycarbonate construction
- 125° Rotational head
- Memory switch – remembers last mode used
- Adjustable non-slip silicone lined headband
- IP65 dust & water resistant
- IK07 super tough construction – 2m drop proof
- High quality 3.7v 1500mAh Li-po battery
- Built-in USB-C charging port with protective cover
- Green Flash-to-Green charging indicator
- 2A USB-C charging – fast 3 hour charge time
- 1m USB-C charging cable included
- Can be wireless charged using Unilite’s WCSGL or WCDBL wireless charging pads
BATTERY – 3.7v 1500mAh Li-po Rechargeable Battery
WEIGHT – 104g
DIMENSIONS – 70 x 52 x 46mm
ADVICE & IMPORTANT INFORMATION!
LEDs will become warm/hot when switched on; do not touch and never place LEDs
face down on any surface – risk of fire!
Do not look directly at the LED. Do not operate in direct sunlight or extreme
temperature conditions (below -10°C or above 40°C).
Do not use the device if there is any visible damage to the housing, charge
port, switch or cable. Take care when using a USB plug adaptor, check for any
damage. DO NOT exceed the stated charging inputs or damage may occur to the
internal battery and may void the warranty.
The rechargeable battery will reach full performance after a few complete
charging and discharging cycles. Fully charge before first use.
To keep the rechargeable battery in optimum condition, it should be recharged
every 3-6 months, especially if it is not being used for a long period of
time. Always fully charge batteries before storage.
Always protect lithium batteries from heat, intense sunlight, fire, water and
moisture – danger of explosion!
If a battery is damaged, fluids can leak out. AVOID contact as this can lead
to skin irritation and/or burns. If skin contact occurs, rinse thoroughly with
water. If irritation persists, seek medical advice. Seek immediate medical
assistance if lithium battery fluid comes into contact with the eyes.
Children under 12 years of age should only use the product under adult
supervision.
Do not open, disassemble or attempt to modify the product; this will void the
warranty and can be dangerous. Improper use or modification is not covered
under the warranty.
Take care not to let the lenses come into contact with hard/sharp objects,
damage/scratches to the lenses will affect light output.
This product is water resistant to IPX5 – DO NOT SUBMERGE. If the product has
been subjected to excessive water the warranty may be void.
This product has a 1 year standard warranty (or extended to 2 years once
registered online at
WWW.UNILITE.CO.UK/WARRANTY) against
manufacturing faults and defects. It does not cover normal wear and tear,
modifications, accidental damage or poor maintenance. Unilite warranties do
not cover disposable battery leakage or the use of incorrect chargers and
cables that can damage rechargeable batteries.
Do not dispose of this device in normal household waste. It must be disposed
of via an authorised electrical appliance disposal centre or at your local
waste disposal unit. Please re-use or recycle packaging where possible.
Keep these instructions for future reference or for subsequent possessors.
OPERATION
TOP SWITCH Sequence:- Spot Beam > Floodlight Low > Floodlight Medium >
Floodlight High > Off
MEMORY FUNCTION:- If left ON in any mode for 5 seconds or more, the next press
will turn OFF. Next press ON will return to that last mode used. 
CHARGING
Option 1 – Direct Charging:
- Only use a 5V USB-C cable (max 2A).
- Lift the charge-port cover on the bottom of the headtorch and plug the USB-C end of the cable into the port.
- Plug the USB-A end of the cable into a USB charging port (do not exceed 5V 2A charging input or damage may occur).
- A green LED on the front of the headtorch will flash to indicate charging. The LED will light up solid green to confirm fully charged.
- Charge Time: 3 hours
Option 2 – Wireless Charging:
- Only use Unilite’s WCSGL single or WCDBL double wireless charging pads.
- Plug the USB-C end of the cable into the charge port on the bottom of the charging pad.
- Plug the USB-A end of the cable into a USB charging port (ensure you pay attention to the max charging inputs on the back of the pad).
- Then place the light onto one of the wireless charging pads taking note of the magnetic connections.
- The green LED on the front of the headtorch will flash to indicate charging. The LED will light up solid green to confirm fully charged.
- Charge Time: 4 hours (based on 2A charging input)
Warranty void if not used with the specified cables/chargers
References
- Ultra Bright, Portable LED Work Lights & Hand Tools | Unilite
- Ultra Bright, Portable LED Work Lights & Hand Tools | Unilite
- Register Unilite Warranty Here - Unilite UK