cocoon HE161192 Touch 3D Printer User Guide
- June 12, 2024
- COCOON
Table of Contents
HE161192 Touch 3D Printer
**User Guide
**
Congratulations on your purchase of the Cocoon Create 3D Printer Touch.
You’re now just moments away from printing your first 3D model. It’s important
that you follow these steps carefully to ensure correct setup of your 3D
Printer.
You can also visit cocoonproducts.com.au for
step by step guides on unboxing and setup, levelling, filament installation
and printing.
Package Contents
1 x Cocoon Create 3D Printer Touch (Extruder Tower, Heated Print Bed)
1 x Filament Spool Holder
1 x Filament Spool Stand
1 x Power Cable
1 x USB Cable
1 x SD Card
1 x Scraper
1 x Replacement PTFE Tube
1 x Hex Key Set
6 x Hex Bolts
.| 2 x Cable Ties
4 x 10m PLA Filament
3 x Print Bed Mats
(1 on Print Bed and 2 spares)
1 x 0.4mm Drill Bit
1 x Extruder Cleaner
6 x Rubber Feet
1 x Levelling Card
1 x Instruction Manual
1 x Getting Started Guide
1 x Warranty Card
---|---
CONSTRUCT AND CONNECT
Place the Extruder Tower and Heated Print Bed on a clean, level work space.
Carefully remove the cable tie that holds the extruder in place.
NOTE : Do not pull on the black cable
NOTE : Ensure printer setup workspace is at least 1m x 1m
Insert the Heated Print Bed Controller carefully through the legs of the
Extruder Tower and align the bolt holes on each side. Using the Hex Wrench,
insert and tighten the two bolts on the bottom of each Extruder Tower
TIP : Raise the extruder and angle the bed for easier inserting through
the Extruder Tower
Insert the long cable connector marked ‘A’ into the motor connector of the Extruder Tower marked ‘A’
Insert the short cable connector marked ‘B’ into the motor connector of the Extruder Tower marked ‘B’
Insert the white connector marked ‘C’ into the motor connector of the ExtruderTower marked ‘C’
Insert the black connector marked ‘D’ into the black connector of the Extruder Tower marked ‘D’
Insert one end of the black cable connector marked ‘E’ into the black connector of the Extruder Tower marked ‘E’. Insert the other end to the black connector marked ‘E’ into the black connector on the side of the Heated Print Bed marked ‘E’
Attach the upper arm of the filament spool holder by unscrewing the end cap, then reattaching. Position the Filament Spool Holder Stand on top of the Extruder Tower, then insert the bolts and tighten with the Hex Wrench
Ensure the power switch is in the OFF position, then insert the Power Supply Cable into the back of the 3D Printer Base. Insert the other end into a nearby mains power outlet. Turn on the power outlet, then turn on the power switch at the back of the 3D Printer Base
Wait for the printer to initialise, with the home screen shown on the Touch Screen. You have successfully setup your Cocoon 3D Printer Touch
LEVELLING THE PRINT BED
IMPORTANT NOTE: Levelling the bed is an extremely important step and if
it is not done correctly every time, your prints will fail or be of poor
quality Before you begin to level the Heated Print Bed:
Ensure the springs on all 4 corners of the Heated Print Bed are tightened all
the way to the bottom by turning each thumbwheel anti-clockwise until you can
no longer turn them. This reduces the distance between the 2 plates of the
print bed to a minimum. Wipe the top of the Heated Print Bed with a clean,
lint-free cloth to ensure no dust particles or other objects are on the Heated
Print Bed Check the Z axis alignment. The X rail (holding the Extruder) should
be parallel to the Heated Print Bed. If it is not, manually rotate individual
z-axis stepper motors on the bottom of both shafts to adjust. Place a Hex
Wrench on the z-axis rod and run it across the Heated Print Bed to check the
z-axis is aligned horizontally Press ‘Level Wizard’ on the touch screen panel
and follow the steps as indicated
NOTE: The distance between the Heated Print Bed and nozzle should be
approximately 0.1mm
LOADING FILAMENT AND PRINTING A FILE
- Turn on the 3D Printer with the Power Switch located at the back of the Printer
- On the Main Screen, select Quick Menu -> Change Filament -> Add Filament
- Select the desired type of Filament to be added. The Extruder will automatically be raised and your Printer will begin heating the Extruder to the correct temperature. When the temperatures are within a few degrees of the target, you are ready to insert the filament
- Place the included filament onto the Spool holder. Carefully insert the end of the filament into the hole on the Extruder. The Extruder will begin to slowly pull the filament in. Once filament begins extruding, press ‘Back’ to stop
- Carefully remove the extruded filament from the Nozzle Head and ensure the Print Bed is clean
- Insert the included SD card into the slot on the right side of the Printer. Select ‘Print’ from Main Screen and choose your desired file from the list. You can now select one of our pre-loaded files below by navigating to, and selecting the file name
- Once selected, your file will begin to load and your file status can be viewed on the touch screen. Your printer will automatically commence heating the Extruder and Print Bed to the correct printing range before commencing the print
- Once your Printer has completed printing the file, the nozzle and Heated Print Bed will automatically commence cooling down. Once cooled, turn off your 3D printer and carefully remove the 3D printed object using the supplied Scraper and gently lifting the object with your hand
NOTE: Always take care when using the Scraper. Never use excessive force
or scrape towards your hand.
NOTE: Always keep the Scraper as level as possible. Scraper can damage
the print mat if not used correctly
NOTE: If your file is not printing correctly, press the ‘Stop’ Button to
discontinue the print. Ensure the extruder is raised prior to removing the
print off the Bed
NOTE: Immediately turn off the machine if any of the motors are jamming
or forcing against the chassis VERSION 1.1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>