Honeywell CT47 Mobile Computer Instructions

: June 12, 2024
: Honeywell

Table of Contents

CT47 Mobile Computer
Product Environmental Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CT47-ML-RS-02-AG Rev (a)
Honeywell CT47 Mobile Computer - barcode
Agency Models: CT47X0N, CT47X1N

CT47 Mobile Computer

Product documentation is available at sps.honeywell.com.
Publicly downloadable certificates are available at honeywell.com/PSScompliance.
Caution: Any changes or modifications made to this equipment not expressly approved by Honeywell International Inc. may void the authorization to operate this equipment.
For body worn operation, this device has been tested and meets the limits regarding human exposure to electromagnetic radiation set forth in related FCC, IC and CE rules, guidelines and standards for use with the following body worn accessory: holster. Use of other accessories may not ensure compliance with the mentioned rules.

****802.11 Caution: A Wireless Network Administrator should review the operating restrictions and use with a properly configured access point.

Models: CT47X0N, CT47X1N
FCC Part 15 Subpart B Class B
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio or television technician for help.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. Honeywell International Inc. is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Honeywell International Inc. The correction is the responsibility of the user.

Use only shielded data cables with this system.

Honeywell International Inc.
hereby declares that the radio equipment types, non-specific
SRD (Models: CT47X0N,
CT47X1N) and cellular (Model:
CT47X1N), are in compliance with the following directives:

2014/53/EU Radio Equipment
2011/65/EU RoHS (Recast)

The full text of the EU declaration of conformity is available at the following internet address: honeywell.com/PSScompliance.
European contact:
Honeywell Productivity Solutions BV
Burgemeester Burgerslaan 40
5245NH Rosmalen
The Netherlands

United Kingdom Contact: United Kingdom Honeywell Scanning and Mobility, Honeywell House, Skimped Hill Lane, Bracknell, Berkshire, RG12 1EB Phone: +44 (0)1344921052

The equipment is intended for use throughout the European Community.
Operating Frequency Ranges
Model: CT47X1N

13-14 MHz (NFC): -24.79 dBµA/m @10m EIRP H-Field
2400-2483.5 MHz (PAN Bluetooth): 18.73 dBm EIRP
2400-2483.5 MHz (Bluetooth Low Energy): 7.28 dBm EIRP
2400-2483.5 MHz (WLAN IEEE 802.11b/g/n/ax): 18.98 dBm EIRP
5150-5350 MHz, 5470-5725 MHz and 5725-5850 MHz (WLAN/RLAN IEEE 802.11a/n/ac/ax): 21.73 dBm, 18.99 dBm and 12.98 dBm (5G B4) EIRP
5925-6425MHz (WLAN IEEE 802.11ax-6E): LPI: 20.64 dBm, VLP: 12.99 dBm
880-915 / 925-960 MHz (UMTS 900 Band, Tx/Rx): 24 dBm
1920-1980 / 2110-2170 MHz (UMTS 2100 Band, Tx/Rx): 24 dBm
880-915 / 925-960 MHz (GSM/EGPRS GSM 900 Band, Tx/Rx): 33 dBm
1710-1785 / 1805-1880 MHz (GSM/EGPRS DCS 1800 Band, Tx/Rx): 30 dBm

LTE Bands (Tx/Rx per 3GPP
specifications. Max Power levels below.)| 5G Bands (Tx/Rx per 3GPP
specifications. Max Power levels below.)
---|---
• Band 1 – 23 dBm| • Band 1 – 23 dBm
• Band 3 – 23 dBm| • Band 3 – 23 dBm
• Band 7- 23 dBm| • Band 7- 23 dBm
• Band 8 – 23 dBm| • Band 8 – 23 dBm
• Band 20 – 23 dBm| • Band 20 – 23 dBm
• Band 28 – 23 dBm| • Band 28 – 23 dBm
• Band 38 – 23 dBm| • Band 38 – 23 dBm
• Band 40 – 23 dBm| • Band 40 – 23 dBm
• Band 41 – 23 dBm| • Band 41 – 23 dBm
• Band 42 – 23 dBm| • Band 77 – 23 dBm
• Band 43 – 23 dBm| • Band 78 – 23 dBm
Restrictions (Revision ERC/REC 70-03 E 2017-02, Annex 3 Band A: 2400-2483.5 MHz):

AZ| No license needed if used indoor and power not exceeding 30 mW.
IT| The public use is subject to general authorization by the respective service provider.
RU| SRD with FHSS modulation
• Maximum 2.5 mW EIRP.
• Maximum 100 mW EIRP. Permitted for use SRD for outdoor applications without restriction on installation height only for purposes of gathering telemetry
information for automated monitoring and resources accounting systems. Permitted to use SRD for other purposes for outdoor applications only when the installation height is not exceeding 10 m above the ground surface.
• Maximum 100 mW EIRP. Indoor applications
SRD with DSSS and other than FHSS wideband modulation
• Maximum mean EIRP density is 2 mW/MHz. Maximum 100 mW EIRP.
• Maximum mean EIRP density is 20 mW/MHz. Maximum 100 mW EIRP. It is permitted to use SRD for outdoor applications only for purposes of gathering telemetry information for automated monitoring and resources accounting systems or security systems.
• Maximum mean EIRP density is 10 mW/MHz. Maximum 100 mW EIRP. Indoor applications
UA| EIRP =100 mW with built-in antenna with amplification factor up to 6 dBi

Model: CT47X0N

13-14 MHz (NFC): -24.79 dBµA/m @10m EIRP
2400-2483.5 MHz (PAN Bluetooth): 18.73 dBm EIRP
2400-2483.5 MHz (Bluetooth Low Energy): 7.28 dBm EIRP
2400-2483.5 MHz (WLAN IEEE 802.11b/g/n/ax): 18.98 dBm EIRP
5150-5350 MHz, 5470-5725 MHz and 5725-5850 MHz (WLAN/RLAN IEEE 802.11a/n/ac/ax): 21.73 dBm and 18.99 dBm and 12.98 dBm
5925-6425MHz (WLAN IEEE 802.11ax-6E): LPI: 20.64 dBm, VLP: 12.99 dBm

802.11a/b/g/n/ac/ax, Bluetooth and NFC
Model CT47X1N: European Community Restrictions: 5250-5350 MHz is for indoor use only; when connecting to LPI access point or bridge, 5945-6425 MHz is for indoor use only.
Model CT47X0N: European Community Restrictions: 5150-5350 MHz is for indoor use only; when connecting to LPI access point or bridge, 5945-6425 MHz is for indoor use only.

| BE| BG| CZ| DK| DE| EE| IE| EL
---|---|---|---|---|---|---|---|---
ES| FR| HR| IT| CY| LV| LT| LU
HU| MT| NL| AT| PL| PT| RO| SI
SK| Fl| SE| IS| NO| LI| CH| UK(NI)
Restrictions (Revision ERC/REC 70-03 E 2017-02, Annex 13 Band El: 5150-5350 MHz, Band E2: 5470-5725 MHz):

AZ| No License needed if used indoor and power not exceeding 30 mW
Restrictions (Revision ERC/REC 70-03 E 2017-02, Annex 9 Band J2: 13553-13567 kHz):

AZ| Not implemented or no information.
BY| Not implemented.
GE| Not implemented.
RU| Maximum magnetic field strength is +42 dBpA/m at 10 m.
UA| The maximal strength of magnetic field on the distance of 10 m from a construction where the radiator is placed
is 42 dBpA/m.

Product Environmental Information

Refer to honeywell.com/PSSenvironmental for the RoHS / REACH / WEEE information.

Models: CT47X0N, CT47X1N
USA, Canada NRTL Safety
cTUVus listed: UL62368-1 3rd Edition, and CSA C22.2 No. 62368-1 3rd Edition.

Warning! To prevent possible hearing damage, do not listen at high volume levels for long periods.

Microwaves
The radio in the computer operates on the same frequency band as a microwave oven. Therefore, if you use a microwave within range of the RF terminal you may notice performance degradation in your wireless network. However, both your microwave and your wireless network will continue to function.

LED Safety
LEDs have been tested and classified as “Risk Group 0 (Exempt)” to the Standard: IEC 62471:2006.

Models with Image Engine: S0703
Laser Compliance and Precaution
This device has been tested in accordance with and complies with IEC60825-1:2014, 21 CFR 1040.10 and 1040.11, except for conformance with IEC 60825-1 Ed. 3, as described in Laser Notice No. 56, dated May 08, 2019.
CT47 devices that include a laser caution label (see far right) affixed to housing are a CLASS 2 LASER PRODUCT. This product has a maximum output of 1 mW at 630-680 nm.

Caution: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

CAUTION
LASER RADIATION
DO NOT STARE INTO BEAM.
CLASS 2 LASER PRODUCT.
RAYONNEMENT LASER.
NE PAS REGARDER DANS
LE FAISCEAU. APPAREIL
À LASER DE CLASSE 2
MAX. 1mW. 630-680nm. Pulse duration 16.8ms IEC 60825-1:2014
Complies with 21 CFR 1040.10 and 1040.11 except for conformance with IEC 60825-1 Ed. 3., as described in Laser Notice No. 56, dated May 8, 2019.
GB 7247.1-2012

RF Exposure Information (SAR)
This mobile phone meets the government’s requirements for exposure to radio waves. This phone is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government and Canadian Government.
The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC/IC is 1.6W/kg and for Europe 2W/Kg. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output.

Model CT47X0N
FCC SAR
The highest reported FCC SAR values for head and body-worn accessory use conditions are: 1.19 W/kg (1g) and 0.71 W/kg (1g).
IC SAR
The highest reported IC SAR values for head and body-worn accessory use conditions are: 1.38 W/kg (1g) and 1.37 W/kg (1g).
CE SAR
The highest reported CE SAR values for head, body-worn accessory and limbs use conditions are: 0.436 W/kg (10g), 0.476 W/kg (10g) and 1.266 W/kg (10g).

Model CT47X1N
FCC SAR
The highest reported FCC SAR values for head, body-worn accessory, hotspot and simultaneous transmission use conditions are: 0.7 W/kg (1g), 1.09 W/kg (1g), 1.09 W/kg (1g), and 1.97 W/kg (10g).
IC SAR
The highest reported IC SAR values for head, body-worn accessory, hotspot and simultaneous transmission use conditions are: 0.7 W/kg (1g), 1.09 W/kg (1g), 1.09 W/kg (1g), and 1.97 W/kg (10g).
CE SAR
The highest reported CE SAR values for head, body-worn accessory and limbs use conditions are: 0.72 W/kg (10g), 1.28 W/kg (10g) and 2.70 W/kg (10g).
While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirement.

The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid afteon FCC ID/IC ID: HD5-CT47X0N/1693B-CT47X0N, HD5-CT47X1N/1693B-CT47X1N.

Caution: If a body worn accessory is not purchased from Honeywell, the accessory must contain no metal and provide a 1.5 cm (0.6 in) space between the device and thebody. Use of antennas and accessories not authorized may void the compliance of this product and may result in RF exposures beyond the limits established for this equipment.

Model CT47X0N
Hearing Aid Compatibility (HAC) Consumer Information
a) This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. In the battery well of this equipment is a label that contains, among other information, a product identifier in the format US: HD5IPNANCT47X0N. If requested, this number must be provided to the telephone company.
b) The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
c) Should you experience trouble with this equipment, please contact Honeywell International Inc, 13509 South Point Blvd, Ste.100, Charlotte, NC 28273, Tel: 800-782-4263 for repair or warranty information. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
d) Please follow instructions for repairing if any (e.g. battery replacement section); otherwise do not alternate or repair any parts of device except specified.
e) This equipment is hearing aid compatible.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
Patents
For patent information, refer to www.hsmpats.com.

This document was prepared and executed in the English language. In the event this document is translated into another language and a conflict arises between the English version and a nonEnglish version, the English version shall prevail, it being recognized and acknowledged that the English language version most clearly expresses the intent of the parties. Any notice or communication given in connection with this document must include a version in the English language.