HolyHah L500RB 2D Bluetooth Barcode Scanner User Guide

HolyHah L500RB 2D Bluetooth Barcode Scanner

Product Information

• Product Name: Bluetooth Barcode Scanner
• Model Number: S2DAS3060RBV0
• Version: User Guide

Bluetooth Pairing Steps:

Pairing Barcode Scanner with Cradle:

1. Step 1: Scan Pairing Code I and then Code II in sequence.
2. After scanning the codes, the LED indicator on the scanner will become blue and flashing.
3. Step 2: Connect the Cradle to the host device using the data cable.
4. Wait for a second, both the LED indicators on the barcode scanner and cradle will become blue to indicate successful pairing.

Pairing Barcode Scanner with Bluetooth Device:

1. Step 1: Scan Pairing Code I and then Code II in sequence.
2. After scanning the codes, the LED indicator on the scanner will become blue and flashing.

Keyboard ON or OFF in IOS Device:

Note: Scan the provided QR code to enable or disable the Keyboard in the iOS device.

Wired Transmission:

Note: Plug in the charging cable to connect to the computer device, then scan the provided setting code to switch to wired transmission mode.

Optional Wireless Modes:

• Upload all data
• Normal: Display all data
• Automatic Storage (default): Upload new data and display new data
• Inventory

Data Delete:

Scan Mode: Manual (default), Continuous, Auto-sensing

Keyboard Caps Lock Control:

*None, Capitalize, Lower Case, Case Swap

Sleep Time Setting:

1Min, 5Min, 10Min, None

Image Inverted Setting:

German, Portuguese, Italy

Suffix Setting:

*Disable, Enable, Add Suffix

Keyboard Language:

Turkey-F, Turkey-Q, USA (default), French, Belgian, Brazilian, Canadian, Japanese, Spanish

Caution and Compliance

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0cm between the radiator and your body.

Factory Default

Bluetooth Pairing Steps

Pair instruction:

A: Barcode Scanner pair with Cradle Step 1, Scan Below Pairing Code I, Code II in sequence, and the scanner LED indicator become blue and flashing.

Step 2, Connect the Cradle to host device through the data cable and wait a second, the LED indicator both become blue on barcode scanner and cradle after succeed pair.
B: Barcode scanner pair with bluetooth device Step 1, Scan Below Pairing Code I, Code II in sequence, and the scanner LED indicator become blue and flashing.

Keyboard ON or OFF in IOS device

Note: Scan above QR code to enable or disable Keyboard in the IOS device .

Wired Direct Transmission Mode

Note: Plug in the charging cable to connect to the computer device, scan this setting code, you can switch to wired transmission mode.

3 Optional Wireless Mode

Note:

1. Normal Mode: the data will be uploaded to host device immediately after scan, out of range it will not save the data, and there will be 2 alarm beeps out of range;
2. Inventory Mode: the data will be saved in the memory chip, and upload data to host device as instructed; Eg: scan the “upload all data and clear”, the scanner will upload all data saved in the memory chip and cleared the original data.
3. Automatic storage Mode:the data will be uploaded to host device immediately after scan if the scanner in range, the data will saved in the memory chip if the scanner out of range which will heard 2 alarm beeps, press the scanner trigger to upload the saved data after back to range, and the original data in the memory chip will be cleared.

Data upload instruction in Inventory Mode

Scan Mode

End Character

Keyboard Caps Lock Control

Sleep Time Setting

Image Inverted Setting

Keyboard Language

UPC-A to EAN13

Prefix Setting

Eg, Add prefix “A”

• Step 1, Scan below code to enter into “add prefix” Step 2, Scan below code to add “prefix”
• Step 3, Scan the numeric code correspond to “A” , the ASCII value of A in Hexadecimal is “4” “1” Refer to Appendix 1 & Appendix 2
• Step 4, Scan “save” code to save (refer to Appendix 1)

Suffix Setting

Note: The method of adding the suffix is the same as the prefix.

Appendix 1

Appendix 2

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference e to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or reloca te the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different f rom that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>