MeTra 95-7376B Double-DIN Dash Kit Instruction Manual
- June 12, 2024
- Metra
Table of Contents
95-7376B
INSTALLATION INSTRUCTIONS
95-7376B Double-DIN Dash Kit
Hyundai Elantra 2017-2018
Visit MetraOnline.com for more detailed information about the product and up-
to-date vehicle specific applications
KIT FEATURES
- ISO DDIN radio provision
- Painted matte black
KIT COMPONENTS
- A) Radio trim panel
- B) Radio brackets
WIRING & ANTENNA CONNECTIONS (sold separately) Wiring Harness: 70-7304 (w/o 7-inch display radio)
- 70-7306 (with 7-inch display radio) Antenna Adapter: N/A (w/o 7-inch display radio)
- 40-KI11 (with 7-inch display radio)
TOOLS REQUIRED
- Panel removal tool
- Phillips screwdriver
Attention! Let the vehicle sit with the key out of the ignition for a few
minutes before removing the factory radio. When testing the aftermarket
equipment, ensure that all factory equipment is connected before cycling the
key to ignition.
DASH DISASSEMBLY
-
Open the passenger front door, then unclip and remove the trim panel from the side of dashboard. Remove the (1) Phillips screw securing the silver trim panel. (Figure A)
-
Unclip and remove the silver trim panel that runs along the dashboard from under the radio, and above the glovebox. (Figure B)
-
Open the driver’s door, then unclip and remove the trim panel from the side of the dashboard. Remove the (1) Phillips screw securing the silver trim panel. (Figure C)
-
Unclip and remove the silver trim panel from under the driver’s side A/C vent. (Figure D)
-
Unclip the trim panel above the steering column, and then unclip and remove the entire panel surrounding the instrument cluster. Note, these two panels are one assembly. (Figure E)
-
Remove the (2) Phillips screws securing the radio trim panel, then unclip and remove the panel. (Figure F)
-
Remove the (4) Phillips screws securing the radio and then remove. Continue to Kit Preparation
KIT PREPARATION
- Remove the (3) Phillips screws securing the A/C vents to the factory radio trim panel and then remove. (Figure A)
- Secure the vents onto the radio trim panel using the factory hardware. (Figure B)
Continue to Kit Assembly
- Attach the radio brackets to the radio using the screws supplied with the radio. (Figure A)
- Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/ or AXXESS. Test the radio for proper operation.
- Secure the assembly into the dash opening using the factory hardware.
- Snap the radio trim panel over the radio assembly, and then reassemble the dash in reverse order of disassembly.
Having difficulties? We’re here to help.
Contact our Tech Support line at:
386-257-1187
Or via email at:
techsupport@metra-autosound.com
Tech Support Hours (Eastern Standard Time)
Monday – Friday: 9:00 AM – 7:00 PM
Saturday: 10:00 AM – 7:00 PM
Sunday: 10:00 AM – 4:00 PM
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.edu or
call
386-672-5771 for more information and
take steps
toward a better tomorrow.
Metra recommends MECP certified technicians
Metra. The World’s Best Kits.®
MetraOnline.com
© COPYRIGHT 2022 METRA ELECTRONICS CORPORATION
REV. 1/6/22 INST95-7376Bhttp://www.metraonline.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>