LAMTTO Rm01 4k Voice Control Mirror Dash Cam User Manual

June 12, 2024
Lamtto

Rm01 4k Voice Control Mirror Dash Cam
User ManualLAMTTO Rm01 4k Voice Control Mirror Dash Cam - icon
11

TOUCH SCREEN STREAMING
VIDEO REAR VIEW MIRROR

Rm01 4k Voice Control Mirror Dash Cam

Important Notice:

  • NOTICE: Due to the high power consumption of this unit,it should always be connected to an external power supply we provided inside package. This camera should not power on without external power supply connected.
  • This product s intended for use in motor vehicle only. DO NOT install the device where it might block the driver s view of road (including the mirrors) or the deployment of the airbag.
  • Before using this device, please insert the memory card first, and need to format micro SD card to FAT32 format on PC firstly, then format the memory card in camera menu.
  • This device records video at high resolution. Be sure to use high speed memory card, Class 10 or above is recommended, support 16GB-128G8 Micro SD Card (Note: Max Support 128GB).
  • We do recommend doinga benchmark test and make sure the unitis working perfectly before installing the unit on your vehicle.
  • Be sure the lens i clean and there is nothing blocking the lens. Make sure you are using the original included power adapter to power the unit.
  • DO NOT leave the device in direct sunlight for a long period of time or where the temperature could go above 170°F(75°C).
  • ‘The GPS function s optional on RMO1 camera, it needs to work with customized GPS module. Please contact the seller for details.

Installation Guide

  1. Before installation, please insert a high speed memory card in the unit and format the memory card in the unit setting, also do a simple test to make sure the unit is working perfectly.

  2. Mount the mirror over the original rearview mirror and use the included rubber ring to fix it. Make sure the mirror is in the right place and secured.

  3. Adjust the mirror angle according to your driving position, make sure the mirror is right in place and the view is clear

  4. Adjust the angle of the lens. Tear off the protective films of the lens. Make sure you get best coverage over the hood and the road ahead, 50 you can record what happens.

  5. Connect the power adapter to the mirror and the cigarette lighter, then route the power cable along the interior trim board, you can route it as indicated below, and hide the excess cable in the gaps for good looking.LAMTTO Rm01 4k Voice Control Mirror Dash Cam - assembly 1

  6. The rearview camera should be installed at the rear end of the car, normally the best place is above the number plate. The camera can be fixed with the sticker or the screw. You can see the diagram for reference.
    (NOTE: Please check whether the backup camera is installed upside down before you install screws)

  7. The excess RED lead near the rear view camera is used for reverse status sensing. Connect the RED cable to the positive lead of the reverse lamp power.LAMTTO Rm01 4k Voice Control Mirror Dash Cam - assembly 2

  8. Route the backup camera cable to the front of the car and connect it to the main unit. There are 2 pictures for reference.
    (NOTICE: Holes might need to be drilled to pass the cable and please check whether the cable for backup camerais long for your car before you install it.LAMTTO Rm01 4k Voice Control Mirror Dash Cam - assembly
3

  9. After the installation is completed, please start the engine and have a test run, make sure all functions are working.
    NOTICE: The wiring and the installation requires certain hand work and some professional electrician skills, if you are not sure about i, please get some professional help.

Adjust the Reversing Camera

Adjust the reversing camera angle, the best angle s the the camera can cover the rear of the car and the ground surface under the rear end.
NOTICE:
When the car s in reverse, the rear camera wil automatically display infull screen, and turn to the lowest angle, o you can see the ground surface under the rear end while reversing.LAMTTO Rm01 4k Voice Control Mirror Dash Cam -
assembly 4

Interface and Button Functions

LAMTTO Rm01 4k Voice Control Mirror Dash Cam - assembly
5 Power button
NOTICE:
Due to safety reasons and high performance of the RMOL mirror, the power consumption of the RMOL is relatively high, it should always be connected to external power supply to ensure working normally.
Power On/ Power Off
Long press the power button for 3 seconds to power on/offthe unit.
Turn off/ Turn on Screen Display
When the unitis on, short press the power button to turn off the screen display, enter the power saving modefthe recording is still working with screen off). Short press the power button or touch the screen to reactivate screen display again.
Reset button
If the recorder somehow crashes or malfunctions, press the [RESET] key to reset the unit and press the [POWER] button again to restart the device.
The main interface and Operations
When the mirror is powered properly, when you start the car engine, the unit wil automatically power on and start recording.
In the video recording interface, touch the screen to call up tool bar. LAMTTO Rm01 4k Voice Control Mirror Dash Cam - assembly
6

| Click to turn ON/OFF audio recording i video,
---|---
| Click to take  photo.
| Click to start/stop video recording.
| Click to enter Setup.
| Clickto enter the camera playback nterface
| Click to manually lock current video.

Shortcut Operation

IN the recording interface, there are several shortcut operation

  1. LAMTTO Rm01 4k Voice Control Mirror Dash Cam - assembly 7In the recording interface, slide horizontally to the right to enter Playback Mode.LAMTTO Rm01 4k Voice Control Mirror Dash Cam - assembly 8
  2. In the recording interface, slide horizontally to the left to switch Front and Rear camera display mode.LAMTTO Rm01 4k Voice Control Mirror Dash Cam - assembly 9
  3. In the main recording interface and on the Right side of the screen, slide vertically up and down to adjust screen brightness.LAMTTO Rm01 4k Voice Control Mirror Dash Cam - assembly 10
  4. In the main recording interface and on the Left side of the screen, slide vertically up and down to move lens view angle.

Playback Mode

LAMTTO Rm01 4k Voice Control Mirror Dash Cam - assembly
11

| Exit
---|---
| Folder Selection
| Wultiple Selection
| Delete
| Playback

Setup Menu

Setup Option How it works
Resolution 4K/2K/1080P Adjust video resolution.
Loop Record 1 min / 3 mins / 5 mins Adjust Loop Recording video clip length.
Record Audio OFF / ON Turn ON / OFF audio recording.
G-Sensor OFF / Low / Middle / High Adjust G-sensor lock sensitivity.
Parking Guard OFF / ON Adjust Parking Guard sensitivity.
License OFF / ON Setup your car license plate number, and watermarked in

video.
Screen Saver| OFF/lmin/3rnin/5rnin| Setup the screen saver activated Se time.
Power Frequency| 50Hz / 60Hz| Setup local power frequency.
Key sound| ON / OFF| Turn ON / OFF operation prompt.
Speaker| Mute / Low / Middle / High| Adjust the speaker volume.
Boot Sound| ON / OFF| Turn ON / OFF system boot up notification.
Back Mirror| ON / OFF| Turn ON /OFF streaming media mode.
Language| English / Chinese / Japanese / Russian / German / French / Spanish / Italian| Setup the system menu language.
Date/Time| Adjustable| Setup local date and time.
Format| Cancel / Confirm| Format the memory card and delete all data.
---|---|---
Default| Cancel /Confirm| Restore the mirror to factory default status.
GPS test| | Test GPS signal.
Time zone| Adjustable| Setup the time zone according to your location.
Speed Calibration| Adjustable| Precision speed.
Speed setting| Adjustable| Setup speed limit.
Speed Unit| KM/H or MP/H| Speed unit adjustment.
Version| | Check software version.
Date stamp| ON/OFF| Video watermark switch
Auto Power Off| OFF/1MIN/3MIN/SMIN| Automatic shut-down
Ars| OFF/ON| Intelligent voice assistant
Ars| Ten voice commands| Turn on screen, Turn off screen, Video start Turn on audio,
Turn off audio. Take photo.
Show front camera.
Show rear camera,
Show both cameras, Lock the video

Featured Function

Dual Recording
“The RMO1 mirror comes with dual channel lens, they can record video in Front 4K (3840 X 2160) + Rear 1080P (1920 * 1080) simultaneously.
Loop Record
“This function allows you to set video file length to 1/3/5 minutes, Select a value to activate loop recording, so when storage fills up, the RMO1 will automatically loop back to the earliest file and record overit.
EG:
If st the time 3 minutes, then the unit will keep recording video in 3 minutes clips. When the card i full the unit will keep recording and overwrite the earlest unprotected 3minutes videa file and so forth.
G-Sensor
The RMOL has a bultin Gravity sensor, in the event of a serious vehicle collision or rapid acceleration / deceleration, the G-sensor will be triggered and immediately lock current video file so the file will not be overwritten by loop record.
Parking Guard
The Parking Monitor is used to protect your car after parking. With this function on, after you stop the car and the unit turns off, it stays in standby, when unit detects significant shock, it will automatically turn on and take a 20 seconds short video, then shut down automatically.
Video recorded under parking monitor will be protected and will not be overwritten by loop recording.
Screen Saver
Set the time after which the unit will automatically turn off screen. Used to save power and reduce distraction while driving. For example,itis setto 3 minutes, if the unit is not operated in 3 minutes, the unit will automatically turn off screen while the recording is still working, any button operation or touch the screen will reactivate the screen display.
Back Mirror
‘The RMO1 mirror features Streaming Media function. With this function on, the camera will display the rear camera view in full screen as default, It will work as a real rearview mirror.
GPS Function
The GPS function is optional on RMOL, it needs to work customized GPS module. Please consult the seller to purchase additional.
With the optional GPS module connected, the RMOL can display current speed on screen. You can enter the setup menu and check the GPS signal status. The speed unit KIM/H and MPH is optional
NOTICE :
The speed displayed is an average speed calculated based on the locations and time, there might be certain errors especially under low speed. It’s for reference only.
GPS Logger
With the optional GPS module connected, the RMOL can record real-time GPS coordinate in the video fle it can be reviewed with the customized GPS player.
NOTICE:
The GPS playback needs customized player “GXPlayer” (Please contact seller support to get it ), for windows operating system only.

Specification:

Model RM01
Screen Display 10 inch (9.66 inch)
Screen Resolution 1280 X 320
Lens Front and Rear Wide Angle Lens
Video Resolution Front:3840X2160PRear:1920X1080P
Video Format MP4
Video Encode H.264
Image Format JPG
Loop Recording Built-in
Parking Monitor Built-in
G-Sensor Lock Built-in
Microphone Built-in
Speaker Built-in
Storage Micro SD Card Up to 128GB (NOT included )
Operating Temperature -20-60°C
Storage Temperature -30-70°C
Operation Humidity 15-65%RH
Power Supply DC W / 2.5A

Common Problem and Solution

Recorder shows memory full, unable to loop video, etc.

  1. First, when a new memory card is used for the first time on the machine. Please format the memory card to FAT32 format on PC then format it in the camera. Or the memory card is previously used on another type of device, it needs to be formatted when used on this camera. Or change another new SANDISK 326 Micro SD card.
  2. Check the sensitivity of G-sensor, if the sensitivity is too high, the bumping and shaking of the camera will trigger the G-sensor, and the file will be locked. Locked files cannot be overwitten. If the lock file is accumulated, there will be no memory card to loop. record. When parking monitoring s turned on, shaking will also cause too many stray fles, which willalso affect the reading and writing of cards

‘The device will automatically turn on or turn off.

  1. Please format the memory card to FAT32 format on PC then formatitin the camera.
  2. Please check whether the parking guard function is on With parking monitor on, the device will automatically turn on and record when it detects a collision o shaking.
  3. Check the car charger connection status, if the connection is 100se, the power supply is not stable, the camera will automatically turn on and off.

The rear camera does not display image

  1. Please switch the camera display mode to double check the rear camerastatus.
  2. Please check if the AV plug is properly connected and the cable is plugged in correctly
  3. Try to disconnect the camera and clean the connector with some medical alcohol connect it again.

Screen operation or button reaction is slow during recording

  1. Please check whether the memory card used s a high-speed card (Class10), If you use a non-high-speed card, problems such as missed seconds, video playback jams, screen display Colorful stripes, and crashes may occur.
  2. Reset the camera if necessary.

Even though set the screen saver, but the screen will randomly come back on.
The power supply might not be stable, please change another car chargertotry.

If you have any other questions or problems, please feel free to contact us at DC@Yooomail.com
We have professional team at your service, and your satisfaction is guaranteed.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals