SEALEY ADB300 356cfm Air Dryer Blower Instructions

SEALEY ADB300 356cfm Air Dryer Blower

SAFETY

ELECTRICAL SAFETY

• WARNING! It is the user’s responsibility to check the following:
• Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all electrical connections for wear and damage.
• Sealey recommend that an RCD (Residual Current Device) is used with all electrical products. You may obtain an RCD by contacting your local Sealey stockist.
• If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance Test) tested.
• Electrical safety information, it is important that the following information is read and understood.
• Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
• Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
• Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse – see fuse rating in these instructions.
• DO NOT pull or carry the appliance by the power cable.
• DO NOT pull the plug from the socket by the cable.
• DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or is replaced immediately by a qualified electrician.
• This product is fitted with a BS1363/A 13 Amp 3 pin plug.
• If the cable or plug is damaged during use, switch off the electricity supply and remove from use.
• Ensure that repairs are carried out by a qualified electrician.
• Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
  • a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
  • b) Connect the BROWN live wire to the live terminal ‘L’.
  • c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
• Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
• Sealey recommend that repairs are carried out by a qualified electrician.

INTRODUCTION

Robust, composite housing, carefully balanced with fully guarded blade drum providing quiet and safe operation. Housing design provides three outlet positions from horizontal to vertical, allowing precise direction of airflow for cooling or drying. Handle incorporates cable storage. Suitable for use in industrial, commercial, agricultural and automotive workshops.

SPECIFICATION

• Model No:…………………………………………..ADB300/ADB3000
• Current:…………………………………………………………….0.5A/5A
• Maximum Airflow:….. 10m³/min(356cfm)/ 81m³/min(2860cfm)
• Power:………………………………………………………..96W/1130W
• Speed(s): …………………………… 1275rpm/ 940/1210/1370rpm
• Supply:…………………………………………………………………230V

OPERATION

1. WARNING! Ensure you read, understand and apply safety instructions before using the blower. Lift the blower by the handle on the main body and manoeuvre it into desired position. Use in any of the 3 positions illustrated overleaf. Ensure that there isn’t anything in front of the blower that may be disturbed when the blower is switched on.

2.  Check that the switch situated in the recess in the rear grille of the blower is set to “0”/OFF. Uncoil the power lead from its stowage

3.  position and plug into the mains power supply. Ensure that the power lead is not stretched or positioned in such a way as to cause a
   hazard.

4. Turn the blower on by switching to “I”/ON. If a greater air flow is required, turn the switch to the “II” or “III” setting (ADB3000 only).

5.  When finished using the blower, ensure the switch is set to the “0”/OFF position and disconnect it from the mains power.

6.  Rewind the lead around the lugs on the carrying handle.

7. When not in use, place the blower in its original box or otherwise protect it from dust, and store in a safe, dry, childproof location.

MAINTENANCE

1. WARNING! Ensure the blower is disconnected from the mains power supply before attempting any of the following.
2.  Use a soft, slightly dampened cloth to clean the body of the blower. Do not splash with water and never allow water to drip onto the motor housing. DO NOT use solvents or other chemicals to clean the blower.
3.  If it becomes necessary to clean the blades or the inside of the body, remove the rear grille (the opposite side to the motor) by undoing the retaining screws. Wipe with a slightly damp cloth only. Re-fit the grille and fix in place using the retaining screws.
4.  Should the motor, speed control box or the power lead require service or maintenance, contact your local service agent.

WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note : It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty : Guarantee is 12 months from purchase date, proof of which is required for any claim

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>