HONDA 08R70-K1Z-J10 Body Mount Shield Instruction Manual
- June 12, 2024
- Honda
Table of Contents
HONDA 08R70-K1Z-J10 Body Mount Shield
Product Information
- Accessory Name: Windscreen
- Parts Number: 08R70-K1Z-J10
- Application Model: After ’18 PCX150/A
- Issue Date: May 2022
- Publication No.: MII 16688
- WARNING: You CAN be KILLED or SERIOUSLY HURT if you don’t follow instructions.
- CAUTION: You CAN be HURT if you don’t follow instructions.
- NOTICE: The purpose of this message is to help prevent damage to your vehicle, other property, or the environment.
- NOTE: Things you want to know, things that are useful to know.
PARTS LIST
- Body mount shield
- Right screen stay
- Left screen stay
- Master cylinder holder
- Rubber washer
- Flange collar
- 6 mm washer
- Handle lever bracket plug
- 6 mm flange nut
- Square nut
- Collar
TORQUE INFORMATION: Refer to the Service Manual for the torque values of the removed parts.
Product Usage Instructions
- Refer to the Service Manual for the motorcycle and remove the necessary motorcycle parts.
- Install the windscreen by aligning it with the punch mark on the mating surface. Make sure to change the mirror position.
- Install the left side of the windscreen in the same manner as the right side.
- Continue the installation as shown in the provided images.
- Adjust the mirror to a position where viewing the rear area is possible.
BODY MOUNT SHIELD
Accessory Name| Parts Number| Application Model| Issue
Date| Publication No.|
---|---|---|---|---|---
Windscreen| 08R70-K1Z- J10| After ’18 PCX150/A| May
2022| MII 16688|
Introduction
ALL INFORMATION, ILLUSTRATIONS, DIRECTIONS AND SPECIFICATIONS INCLUDED IN THIS
PUBLICATION ARE BASED ON THE LATEST PRODUCT INFORMATION AVAILABLE AT THE TIME
OF APPROVAL FOR PRINTING. Honda Motor Co., Ltd. RESERVES THE RIGHT TO MAKE
CHANGES AT ANY TIME WITHOUT NOTICE AND WITHOUT INCURRING ANY OBLIGATION
WHATSOEVER. NO PART OF THIS PUBLICATION MAY BE REPRODUCED WITHOUT WRITTEN
PERMISSION. THIS MANUAL IS WRITTEN FOR PERSONS WHO HAVE ACQUIRED BASIC
KNOWLEDGE OF MAINTENANCE ON Honda MOTORCYCLES, MOTOR SCOOTERS OR ATVS.
Honda Dealer: Please give a copy of these instructions to your customer.
Customer: Because it requires specialized knowledge and special tools and
equipment, it is recommended to install it at a dealer with qualified
automobile maintenance.
How To Read These Symbols
Your safety, and the safety of others, is very important. To help you make
informed decisions we have provided safety messages and other information
throughout this manual.
- WARNING You CAN be KILLED or SERIOUSLY HURT if you don’t follow instructions.
- CAUTION You CAN be HURT if you don’t follow instructions.
- NOTICE The purpose of this message is to help prevent damage to your vehicle, other property, or the environment.
- NOTE Things you want to know, things that are useful to know.
- Follow the instructions in the Service Manual.
- Follow the other symbol instructions of the “Installation Instructions BASIC”.
Instruction Other Symbols
The symbols used throughout these instructions show specific service
procedures. Refer to “Installation Instructions BASIC” for a description of
each symbol.
INFORMATION
CAUTION: To prevent burns, allow the engine, exhaust system, radiator,
etc., to cool before installing the accessory.
NOTICE : Take care not to damage the painted surfaces of the motorcycle.
NOTICE : This item cannot be installed at the same time as the knuckle
visor. Save all removed parts unless otherwise indicated.
PARTS LIST
| Component | No. | Parts Name | Qty | Parts No. |
|---|
|
(1)| Body mount shield| 1| –
(2)| Right screen stay| 1| –
(3)| Left screen stay| 1| –
(4)| Master cylinder holder| 2| 45518-MFN-D01
(5)| Rubber washer| 8| 08R80-KTW-80039
(6)| 6×20 mm socket bolt| 4| 08R80-KTW-80072
(7)| Flange collar| 4| 08R80-KWN-80017
(8)| 6 mm washer| 2| 94101-06700
(9)| 6×35 mm socket bolt| 2| 96600-06035-07
(10)| Handle lever bracket plug| 2| 53174-463-770
(11)| 6 mm flange nut| 4| 94050-06070
(12)| 6×12 mm washer bolt| 2| 93404-06012-08
(13)| Square nut| 2| 50318-K97-T00
(14)| Collar| 4| 08R00-K96-J00
TORQUE INFORMATION
Refer to the Service Manual for the torque values of the removed parts.
INSTALLATION
- Refer to the Service Manual for the motorcycle, remove the motorcycle parts as shown.
INSTALLATION IMAGE 
- Install as shown.
- Install the left side in the same manner as the right side.
- Install as shown.
- Install as shown.
- Install as shown.
- Install as shown.
- Install the motorcycle’s parts in the reverse order of removal.
- Confirm that any harness is not caught or too tight.
- Adjust the mirror to a position where viewing the rear area is possible.
- Turn the handlebar to the left and the right and confirm that itdoes not interfere with the body mount shield.
- Keep a distance of 10 mm to the body mount shield.
© Honda Motor Co., Ltd. 2020 72K1Y010
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>