inox-bazis Electric Bain Marie Instruction Manual
- June 12, 2024
- inox-bazis
Table of Contents
inox-bazis Electric Bain Marie
Product Information
Electric Bain Marie
- Website: www.inoxbazis.hu
- Customer Support: +36 1 788-1828
General Description
The Electric Bain Marie is a stainless steel countertop device with three-
sided coverage. It features internal filament heating and optional accessories
such as a wheelset, external heating blanket, filling tap, and bottom heating.
Please note that the GN container is not included as a standard accessory.
Technical Data
- Model: RMKM3GN11
- Size: N/A
- Capacity: N/A
- Heating Filament Performance: 1 kW
- *Heating Blanket Performance:** 1.3 kW
- Thermostat: N/A
- Model: RMKM4GN11
- Size: N/A
- Capacity: N/A
- Heating Filament Performance: 1 kW
- *Heating Blanket Performance:** 1.3 kW
- Thermostat: N/A
- Model: RMKM5GN11
- Size: N/A
- Capacity: N/A
- Heating Filament Performance: 1 kW
- *Heating Blanket Performance: 1.3 kW Thermostat:** N/A
The version with a heating blanket is an extra option.
Product Usage Instructions
Cleaning
To clean the Electric Bain Marie, follow these steps:
- Wait for the machine to cool down and disconnect it from the electrical network.
- Wash all metal parts with warm water and neutral detergent.
- Rinse thoroughly to remove any remaining dirt.
- Dry with a dry cloth.
- Avoid using abrasive or corrosive cleaning agents as they may damage the metal parts.
Note : If the machine is not used for a long period of time, clean it thoroughly and disconnect it from the electrical network. In case of a breakdown, switch off the machine immediately and contact a mechanic.
Draining the Water
- Prepare a suitable container to collect the drained water.
- Open the drain tap to drain the water.
Note: The device connected to the mains can be filled directly with the tank filling inlet, which is available as an option, and the water draining can be simplified with the drain tap, which is connected to the mains.
Maintenance
All maintenance operations should only be carried out by trained personnel.
Follow these steps:
- Switch off the machine and disconnect it from the electrical network.
- When switching off, turn off the main switch to cut off the power supply.
- If the lighting needs replacement, disconnect the device first and then replace the lamp.
Please refer to the user manual for more detailed instructions and safety information.
Dear Customer!
First of all, thank you for choosing us and honoring us with your trust! We
hope that you found everything in ideal condition and are satisfied with the
product! Before using the product, make sure that it has been assembled and
installed in accordance with the instructions!
ATTENTION
The equipment may only be used by trained personnel!
- Never leave the device on without water in the tank!
- Do not leave children or disabled people unattended with the device in one space!
- Always observe site-specific safety, occupational safety, fire and accident prevention, and hygiene regulations!
- The manufacturer is not responsible for damages resulting from improper use, maintenance, and repair work performed by non-professionals nor for the proper functioning of non-original spare parts.
- Place the device on a straight, flat, solid surface, in a place that complies with the regulations, so that there is no danger of tipping over or slipping.
- To connect to the electrical network, it is advisable to install a circuit breaker between the equipment and the network.
- With regard to the establishment of safety regulations, MSZ HD 60364- 4- 41:2007 standard, the provisions of MSZ EN 61140:2003 must be taken into account with regard to contact protection regulations.
- Do not operate the device without effective touch protection!
- Always check if the device is working properly during use. If you notice an error, disconnect the machine from the network and call a specialist.
CLEANING
Do not clean the device with a high-pressure water jet! Before cleaning, wait
for the machine to cool down and disconnect the device from the electrical
network. Wash all metal parts with warm water and neutral detergent, then
rinse thoroughly to remove any remaining dirt from the machine. Use a dry
cloth to dry. Do not use abrasive or corrosive cleaning agents as they may
damage the metal parts of the equipment.
In the event that the equipment is not used for a long period of time, clean
it thoroughly and disconnect it from the electrical network. If the machine
breaks down, switch it off immediately and contact a mechanic.
GENERAL DESCRIPTION
The counters are covered on three sides, are normally opened in the front, and
have a bottom shelf. All counters are made of stainless steel. The device is
equipped with internal filament heating. Optional: wheelset, external heating
blanket, filling tap, bottom heating. The GN container is not a standard
accessory!
ATTENTION! THE MANUFACTURING COMPANY RESERVES THE RIGHT TO MAKE ANY
CHANGES DEEMED NECESSARY TO IMPROVE THE MACHINE, AND TOGETHER WITH THE
DISTRIBUTION THE COMPANY, DISCLAIMS ANY LIABILITY FOR DAMAGES RESULTING FROM
IMPROPER USE.
This product contains components that are classified as hazardous waste, which
– depending on the type of machine – includes coolant gases, coolants,
electronic (semi)conductors, etc. contains, which seriously
damages the environment, that is why it can only be collected separately as
waste! During the development of the manufacturer’s technology, it devotes a
significant proportion of its income to research and development in order to
reduce the amount of waste from e+e equipment and make their reuse,
utilization, and processing significantly easier.
TECHNICAL DATA
The version with a heating blanket is an extra option.
RMKM3GN11 | RMKM4GN11 | RMKM5GN11 | |
---|---|---|---|
Size: | 1150×700×850 mm | 1500×700×850 mm | 1800×700×850 mm |
Capacity: | 3×GN1/1 | 4×GN1/1 | 5×GN1/1 |
Heating filament performance: | 1 kW | 2,5 kW | 2,5 kW |
Heating blanket *performance:** | 1,3 kW | 2,6 kW | 2,6 kW |
Thermostat: | 30-90°C | 30-90°C | 30-90°C |
RMAM3GN11 | RMKM4GN11 | RMAM5GN11 | |
--- | --- | --- | --- |
Size: | 1150×700×850 mm | 1500×700×850 mm | 1800×700×850 mm |
Capacity: | 3×GN1/1 | 4×GN1/1 | 5×GN1/1 |
Heating filament performance: | 1 kW | 2,5 kW | 2,5 kW |
Heating blanket *performance:** | 1,3 kW | 2,6 kW | 2,6 kW |
Thermostat: | 30-90°C | 30-90°C | 30-90°C |
BODY ASSEMBLY
Different types of superstructures and breathing protection glass can be
ordered for the electric bain maries. Attention: The counters are sold without
a superstructure by default in order to make them easier to transport. In this
case, the assembly is carried out by the customer. If the customer also
requests assembly, this must be indicated to the manufacturer. In this case,
the specialist representing the manufacturer will carry out the assembly at
the location for an additional fee.
INSTRUCTIONS FOR ASSEMBLY OF THE GLASS STRUCTURE
The glass must be slid into the glass holders (1) located below. The glass
must be screwed with the help of the “L” shaped side element (2) or the corner
element (3) into the holes placed in the column above. It is
important that the silicone rubber ring (4) in the assembly package is placed
at the junction of the glass and metal parts. The thermal expansion of glass
and metal is not the same, the 1 mm plastic ring serves to
balance of this factor. Without the plastic ring, there is an increased risk
of breakage of the fixed screws during use, the glass will break sooner or
later even with normal use, so make sure that the glass is
properly fixed!
STARTING THE BAIN MARI
Remove the protective folie of the device. Before first use, clean the device
thoroughly with a damp cloth and a neutral detergent. It is equipped with a
wire and plug, which can be used to connect to the 230V / 50Hz electrical
network. Make sure that the drain valve is closed. Fill the tank with water to
cover the bottom by at least 5 cm, then turn on the machine with the main
switch. The device is equipped with a heating wire built into the most modern
silicone sheet known today, but if there is no water in it, it will overheat
and, of course, it can burn out. Turn on the main switch and use the rotary
knob to set the thermostat to the desired temperature (between 30-90 C). After
that, the thermostat is no longer needed to turn it on and off, only the main
switch is used to turn it on and off.
DRAINING THE WATER
First, get a suitable container into which the water can be drained. Then open
the drain tap. The device connected to the mains can be filled directly with
the tank filling inlet, which is available as an option, and the water
draining can be simplified with the drain tap, which is connected to the
mains.
MAINTENANCE
All maintenance operations may only be carried out by trained personnel. In such cases, always switch off the machine and disconnect it from the electrical network. When switching off, turn off the main switch, then the power supply to the device will be cut off. The lighting works by turning on the main switch, in case the replacement is needed, it is important to disconnect the device first and then carry out the replacement of the lamp.