BROAN 10459630 Damper Kit for Split System Air Conditioner Instruction Manual
- June 12, 2024
- Broan
Table of Contents
BROAN 10459630 Damper Kit for Split System Air Conditioner
Product Information
The Clip-on Damper kit is designed for use with Split System AC & HP units.
It is primarily used to dampen vibrations between the unit’s fan grille and
top pan, preventing noise issues caused by the fan grille vibrating against
the top pan. The kit includes 8 Clip-On Dampers and 1 set of Installation
Instructions.
Product Usage Instructions
- Before starting the installation, ensure that the power to the unit is turned off.
- Locate the fan grille on the unit.
- Attach the Clip-On Dampers to the fan grille in the specified locations shown in Figure 1.
- Ensure that all dampers are securely attached.
- Once the dampers are attached, turn on the power to the unit and test for any noise issues caused by vibration.
Important
This installation should only be performed by qualified individuals
experienced in servicing heating and air conditioning appliances. It is
essential to follow all safety warnings and instructions provided in the
manual. Failure to do so may result in personal injury, property damage, or
dangerous operation of the unit.
Note: If you are unsure about interpreting these instructions or installing the equipment, it is recommended to seek assistance from a licensed installation/service personnel. For further information or assistance, please refer to the complete user manual or contact our customer support.
Clip on Damper kit for Split System AC & HP
IMPORTANT SAFETY INFORMATION
These instructions are primarily intended to assist qualified individuals
experienced in the proper servicing of heating and air conditioning
appliances. Some local codes require licensed installation/service personnel
for this type of equipment. Use of this kit must be in accordance with these
instructions and with all applicable national and local codes and standards.
INSTALLER : Please read all instructions thoroughly before servicing this equipment. Pay attention to all safety warnings and any other special notes highlighted in the manual. Safety markings are used frequently throughout this manual to designate a degree or level of seriousness and should not be ignored.
WARNING – Indicates a potentially hazardous situation that if not avoided, could result in personal injury or death.
WARNING:
ELECTRICAL SHOCK, FIRE OR
EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury or
property damage. Improper servicing could result in dangerous operation,
serious injury, death or property damage.
- Before servicing, disconnect all electrical power to the furnace.
- When servicing controls, label all wires prior to disconnecting. Reconnect wires correctly.
- Verify proper operation after servicing.
WARNING
The safety information listed in this manual must be followed during the
installation, service, and operation of this unit. Unqualified individuals
should not attempt to interpret these instructions or install this equipment.
Failure to follow safety recommendations could result in possible damage to
the equipment, serious personal injury, or death.
ABOUT THE CLIP-ON DAMPER KIT
This clip-on damper kit includes the following items:
Description
Quantity
Clip-On Dampers …………………………………8
Installation Instructions…………………………1
The clip-on dampers supplied with this kit are designed to dampen any vibration between the unit’s fan grille and top pan. This prevents the fan grille from vibrating against the top pan and causing noise issues. These clip-on dampers should only be needed if a unit is confirmed to have noise generated by the fan grille vibrating against the top pan.
INSTALLATION SEQUENCE
-
IMPORTANT! Turn the power off to the unit.
-
Attach the clip-on dampers to the grille in the locations shown in Figure 1. Push the open end of the clip on the damper down over the round metal rods of the fan grille. Make sure the flat paper-covered end is pointing up.
-
Remove the 4 screws securing the fan grille to the top pan. Do not discard the screws.
-
Slightly lift the fan grille up with one hand and rotate the clip-on damper with the other hand so that the flat paper-covered end is pointing down.
NOTE : This process may need to be repeated a couple of times in order to get all 8 of the clip-on dampers rotated properly. -
Lower the fan grille back into position.
-
Install the 4 screws removed earlier in Step 3.
-
Restore power to the unit and check unit operation
INSTALLER: Leave these instructions with the equipment owner. Specifications & illustrations are subject to change without notice or incurring obligations (07/23). O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>