LUVIEW JY-6731W Wireless Rear View System Instruction Manual

LUVIEW JY-6731W Wireless Rear View System

Product Information

• Product Name: Wireless Rear View System
• Contents: 1 unit
• Precautions:
  • The device can be powered by a 12 or 24 volt automotive battery or vehicle electrical system.
  • Ensure all cables are properly connected and observe polarity to avoid damaging the monitor.
  • Remove power cable connections when the unit is not in use.
• Maintenance:
  • Disconnect all cable connections before cleaning the unit.
  • Use a mild household detergent and a slightly damp, soft cloth to clean the unit.
  • Avoid using strong solvents such as thinner or benzene as they may damage the device.
• Product Features:
  • High-definition 7-inch TFT LCD display
  • Automatic pairing
  • Wide-angle viewing angle
  • High-resolution display
  • Supports 4-channel simultaneous video recording and video playback
  • Four-screen display mode, dual-screen display mode, auto-scanning mode, and single-screen display mode
  • Touch screen for all operations
  • Infrared remote control for all operations
  • Selectable national menu language (Chinese, English, French, German)
  • Supports audio input from four cameras at once (optional)
  • Automatic trigger control line switching
  • Automatic camera image or segmentation switching in standby state
  • SD card lock to prevent loss
  • TF card storage capacity of 128G
  • Working power supply range: DC12~24V
  • Power supply short circuit protection function
  • Adjustable bracket angle
• Technical Specifications:
  • Monitor SETUP display screen: Can be set to divide the 5th channel trigger display into two or four divisions (default: four divisions)
• Menu setting operation:
  • Camera parameters can be independently set for brightness, contrast, saturation, hue, and volume of CM1-CAM4 (default:50)

Product Usage Instructions

1. Before operating the Wireless Rear View System, ensure that you have read the entire user manual for proper understanding and reference.
2. Power Supply:
   • The device can be powered by a 12 or 24 volt automotive battery or vehicle electrical system.
   • Make sure all cables are connected properly and observe polarity to avoid damaging the monitor.
   • Remove the power cable connections when you do not intend to use the unit.
3. Maintenance:
   • Before cleaning the unit, remove all cable connections from the monitor.
   • Use a mild household detergent and clean the unit with a slightly damp, soft cloth.
   • Avoid using strong solvents such as thinner or benzene as they might damage the device’s finish.
4. Product Features:
   • The Wireless Rear View System features a high-definition 7-inch TFT LCD display with automatic pairing.
   • It offers a wide-angle viewing angle and high-resolution display.
   • Supports 4-channel simultaneous video recording and video playback.
   • Four different display modes are available: four-screen display mode, dual-screen display mode, auto-scanning mode, and single-screen display mode.
   • All operations can be performed using the touch screen or the included infrared remote control.
   • The menu language can be selected from Chinese, English, French, or German.
   • Optional audio input is supported from up to four cameras simultaneously.
   • The system automatically switches the trigger control line when triggered.
   • In standby state, the system automatically starts and switches to the corresponding camera image or segmentation state.
   • The SD card can be locked to prevent loss, and the TF card storage capacity is 128G.
   • The working power supply range is DC12~24V, with power supply short circuit protection function.
   • The bracket angle is adjustable for optimal positioning.
5. Technical Specifications:
   • The SETUP display screen allows you to set whether the 5th channel trigger display is divided into two or four divisions. The default value is four divisions.
6. Menu Setting Operation:
   • To access camera parameter settings, click on “Camera parameters”.
   • Brightness, Contrast, Saturation, Hue, and Volume of CM1-CAM4 can be independently set between 0-99. The default value is 50.

Precautions

Storage and keeping

1. Do not expose the monitor to excessive heat or cold. The storage temperature of this device is -30 ~+80℃, and the operating temperature is -10 ~+65℃. The Humidity is Rh90%.
2. Never use this device near a bathtub, wash basin, kitchen, damp basement, swimming pool or similar place.
3. Never use this device in environments with excessive moisture, dust or smoke.
4. Avoid dropping or striking this device.
5. Avoid using this device in enclosed spaces, areas with excessive vibration or subject to severe impacts.
6. Never puncture, scratch or use abrasive cleaning materials on this device.
7. Do not place cables where they may be pinched or stepped on.
8. Leave at least a 2”space between the monitor and walls, cabinets or other objects to allow adequate air circulation around the unit.
9. The monitor is not designed to be waterproof.

Operating Precautions

1. The device may be powered by a 12 or 24 volt automotive battery or vehicle electrical system.
2. Make sure all cables are connected properly observe polarity. Improper cable connections may damage the monitor. Remove the power cable connections when you do not intend to use the unit.

Warning!

1. High voltage is present within the monitor. The opening of the case should be by professionals.
2. Do not watch the video while driving unless you are monitoring the rear view camera display.

Special Notice
Occasionally, a few highlights or dark spots may occur on the LCD screen. This is a very common phenomenon in active matrix display technology, and doesn’t necessarily indicate any defects or faults. Never try to repair this device by yourself. In case of any problems, please turn off the display at once and notify our company or authorized dealer. The monitor is a complex device. Any disassembly or modification may lead to damage and void the warrantee.

Maintenance

1. Remove all the cable connections from the monitor before cleaning the unit.
2. Use a mild household detergent and clean the unit with a slightly damp, soft cloth. Never use strong solvents such as thinner or benzene, as they might damage the furnish of the device.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
This symbol is intended to alert the user not to waste electrical and electronic equipment.

CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual could void your warrantee and necessitate expensive repairs.

Declaration of conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
（1）This device may not cause harmful interference.
（2）This device must accept any interference received, including Interfered that may cause under sired operation.

Product Features

1. High-definition 7-inch TFT LCD display, supports automatic pairing, has wide-angle viewing angle and high-resolution display, supports 4-channel simultaneous video recording and video playback.
2. Support 4-channel simultaneous video recording and video playback.
3. Four-screen display mode, dual-screen display mode, auto-scanning mode and single-screen display mode are available.
4. With touch screen, all operations can be realized by touch.
5. With infrared remote control, all operations can be realized by remote control.
6. National menu language can be selected (Chinese, English, French, German).
7. Support audio input from four cameras at once (optional).
8. Each trigger control line switches automatically when triggered.
9. In standby state, the trigger automatically starts and switches to the corresponding camera image or segmentation state.
10. With SD card lock, you can lock the SD card to avoid loss of the SD card, the storage capacity of the TF card is 128G.
11. The working power supply range is DC12~24V, and the power supply short circuit protection function.
12. Bracket adjustable angle.

Special Notice
All specifications are subject to change without notice.

Technical Specifications

Monitor

1. 7″/16： 9 Monitor with Digital Panel
2. Resolution: 2.1024（W） R.G.B 600(H)
3. Brightness: 650cd/㎡
4. Contrast: 800:1
5. Visible range: 154.21(H) × 85.92 (V)
6. Viewing angle: Left/Right/Up/Down 85°/85°/85°/85°
7. Image Settings: Brightness, Chroma, Contrast
8. Video format: MP4
9. Audio and video channels: 4 audio/video inputs
10. Reversing function: 4-way reversing (ruler setting function)
11. Reverse delay: 0～60S
12. Power voltage: 12V-24V，DC/<6W
13. Speaker: 0.5W/50Ω
14. Emitting frequency: 17 dBm
15. Operating temperature: -20℃ to +70℃
16. Storage temperature: -30℃ to +80℃

Camera

• 1/2.9 CMOS
• Resolution: 1280 X 960/720P
• Lens: 2.8mm
• Min illumination: 0.01 Lux
• Night Vision distance: 5-10M
• Waterproof rating: IP 69K
• Video format：MP4
• View angle: H：105° V：54° D：111°
• Power voltage: DC:12V~24V
• Current consumption：DAY:145±5mA；Night:230±5mA
• Working environment temperature: -20℃+ 70℃，humidity up to 95%
• Storage temperature: -30℃+ 80℃, humidity up to 95%
• Microphone：√

Remote Remote

1. MUTE key: turn on volume and mute
2. OK key: confirm key
3. ←VOL key: volume down and the previous item in the menu
4. PAIR key: no effect
5. POWER key: On/off power key, used to control the power on and standby of the screen
6. MENU key: open the menu and return key
7. →VOL key: Volume plus and the next item in the menu
8. SEL key: switch channel key
9. MIR key: no effect
10. SYS key: no effect

Install

Mounting brackets
After adding the support silicone pad, lock the six-petal torx screw in place .

Install the sun cover
Put the sunshade cover on the panel and align it with the 4 card slots and press it in place, and then lock the screws in the card slots 1 and 2 .

Connection Diagram

Wire connection

1. Yellow: The yellow line is the trigger line connected to CAM1
2. White: The white line is the trigger line connected to CAM2
3. Green: The green line is the trigger line connected to CAM3
4. Blue: The blue line is the trigger line connected to CAM4
5. Black: The black wire is connected to the power GND
6. Brown: The brown line is the trigger split interface
7. Red: The red wire is connected to DC+12~24V

Connection Diagram

Menu setting operation

Startup Screen

1. Power on: start within 3S after power on.
2. Standby: Swipe down on the screen to standby, swipe up on the screen to power on.

Menu Screen
Click the center 1/4 area of the touch screen to call out the menu, and click other areas outside the menu to close the menu.

• Switch channel: click Can choose to switch between CAM1-CAM4, two-division, four-division, cycle channel mode.
• Split channel volume: click Set a single channel with sound in the split channel, default value: channel 1 with sound.

**

**

1. Automatic pairing: click Enter the automatic pairing mode, press √ to show that the pairing is successful.
   Note: The pairing can be successful only after clicking pair within 7 seconds of the TX camera being powered on.

2. Video playback: click 4-split playback or single-channel playback can be selected.

3. Pause\Start recording: Click Can start/pause recording。

4. Main Menu: Click Enter the submenus of recording settings, reversing line adjustment, automatic scanning settings, etc.

5. Record recording settings: click Enter recording settings. Record Time: 1Min, 3Min, 5Min can be set, the default value: 3Min Format SD Card: Click to format SD card
   Date &Time：Click to set time and date

6. Parking Line: Click Enter the reversing line adjustment. ON: Reverse line on OFF: Reverse line off Default: ON click Set the position of the reversing line

7. Auto Scan: click Enter auto scan settings.
   ON: Turn on auto scan OFF: Turn off auto scan Default: ON Can independently set CAM1-CAM4, double-split, four-split channel automatic scan time Default value: 10 seconds

8. Trigger: click Enter the trigger line setting, with 4 single channel trigger and 1 split screen trigger.
   Delay trigger return time: CAM1-CAM4, split channel trigger return time can be independently set, default value: 2 seconds, maximum 60 seconds
   Priority trigger priority: For example, set the default value to 2, 3, 4, 1, 5, then CAM4>CAM1>CAM2>CAM3>Segment
   SETUP display screen: It can be set whether the 5th channel trigger display is divided into two or four divisions, the default value: four divisions

9. Camera parameters: click Enter camera parameter settings.
   Brightness, Contrast, Saturation, Hue, Volume of CM1-CAM4 can be independently set, and can be configured between 0-99, the default value: 50.
   CM1-CAM4 can be set independently for horizontal mirror H Mirror and vertical mirror V Mirror, the default horizontal mirror: OFF, vertical mirror: OFF

10. Dual View: click Enter the dual-split screen setting, you can set any two channels of CM1-CAM4 to double-split screen display.

11. Quad View: click Enter the four-split screen setting, you can set any four channels of CM1-CAM4 to four-split screen display.

12. System: click enter system settings.
    Dimmer Backlight: Click to adjust the brightness of the screen backlight, default: 99.
    Auto Backlight: Default: OFF, click after turning on Adjustable automatic Adjustable automatic backlight brightness.
    System Upgrade： Click Upgradable system.
    Language： Click Four languages can be selected (Chinese, English, French, German), default: English.
    Reset： Click Factory reset possible.

13. Power ON: click Enter the startup screen settings, you can preset the default display channel for startup.

Common malfunctions

Accessories

Guarantee

The statutory warranty period will be valid of one year after sold In case of defaulted product, please contact:

• Your retailer
• your fitter

For repair and maintenance after sold, please include the following documents when you send back:

• A copy of the receipt with purchasing date
• A reason for the claim or description of the fault

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>