SCREENLINE 2022 LODO EVO Screen Instruction Manual

SCREENLINE 2022 LODO EVO Screen

Product Information
The product is a screen that is designed to be installed in a room for various purposes. It comes with brackets and other accessories for installation. The screen is sensitive to heat and should not be placed in front of sunlight windows or near heat sources like radiators, fireplaces, or stoves. Improper installation may damage the motor and control system, and any deviation from the procedures described in the manual will void the warranty.
Product Usage Instructions
Installation Preparation

1. Position the empty packaging in the installation room, ensuring that the screen is positioned with its front side in the right direction.
2. Unpack the screen.

Wall Brackets Installation

1. Prepare the bracket by separating the part to be installed on the screen.
2. Install the wall brackets according to the indication of 400/600 mm. The screws will already be in the correct position.
3. Install the part of the bracket on the screen in the same position as the screws.
4. Rotate the hook to lock the bracket.

Ceiling Brackets Installation

1. Install the ceiling brackets as indicated.
2. Rotate the hook to lock the bracket.

Screen Installation

1. Install the lower part of the bracket on the screen. Refer to page 4 for detailed instructions.
2. Rotate the hook to open or close the bracket.

Eyebolt Bracket Installation

1. Remove the lower part of the bracket.
2. Install the lower part of the bracket on the screen. Refer to page 4 for detailed instructions.
3. Rotate the hook to open or close the bracket.

Wall Safety Chains Installation
Regulate the counterweight to flatten the fabric of the screen, only if there are waves.
WARNING: The PVC fabric is sensitive to heat. Avoid placing the screen in front of sunlight windows or near heat sources. Excessive heat can cause the fabric to soften and stretch, altering the video ratio and deforming the surface.

Place the empty packaging in the installation room making sure that the screen is positioned with its front side in the right direction.

Unpackaged the screen

• The installation must be carried out by qualified staff: the team in charge will have to unload, hoist and anchor the screen and connect the wiring.
• The improper installation of the system may damage the motor and the control system. The installation not in compliance with the given i nstructions will nullify the warranty!
• DURING THE HOISTING PROCESS IT IS STRICTLY FORBIDDEN TO WALK IN THE AREA UNDERNEATH THE SCREEN. ANY MISTAKE IN THE INSTALLATION OF THE SYSTEM COULD BE FATAL!
• Any divergence from the procedures laid out in this manual will not be covered by the warranty.

Wall brackers installation

Part of the bracket that must be installed on the screen

Wall brackets installation

Install brackets according to the indication 400/600 mm. The screws will be already in the correct position 400/600 mm. Install the part of the bracket that must be installed on the screen in the same position as the screws.

Wall brackets installation

Ceil brackets installation

Screen installation

In the case of truss installation: Aliscaf brackets

Remove the lower part of the bracket.

See page 4 to install the lower part of the bracket to the screen Rotate the hook to open and close the bracket

Eyebolt bracket

Remove the lower part of the bracket.

See page 4 to install the lower part of the bracket to the screen Rotate the hook to open and close the bracket

Wall safety chains

WARNING

The PVC fabric is very sensitive to heating. In a very hot environment, the fabric can be softer excessively and stretch down by altering the video ratio. You should absolutely avoid placing the screen in front of sunlight windows or above radiators, fireplaces, and stoves of all kinds. The higher will be the heating absorbed by the screen, the higher will be the deformation of the surface which will assume an elongated shape with curved lateral edges.

INFERIOR LIMIT POINTS’ CHANGING

WARNING: When delivered, the motor is set to “working” mode. To change the set points it is necessary to proceed with the cancellation of the points set by the manufacturer. IT IS ESSENTIAL NOT TO MODIFY THE DOWN LIMIT POINT SET BY THE MANUFACTURER OVER ± 10 CM.

(Otherwise, the warranty shall not apply)

1. Open the screen to the middle position;
2. CLEAR ALL ADJUSTMENTS (This can only be done using a double button that is not interlocked) Press UP AND DOWN at hte same time for 8”, until the screen moves UP AND DOWN 2 times.
3. ENTER PROGRAMMING MODE Press UP and DOWN simultaneously until the screen moves UP and DOWN Press UP and DOWN at the same time for 8”, until the screen moves UP AND DOWN 2 times.
4. ADJUSTMENT OF THE DOWN LIMIT SWITCH Pressing DOWN, bring the screen to the down limit point Press UP quickly, release, and press RISE again for 3”, until the screen moves UP and DOWN.
5. STORAGE OF THE LIMIT SWITCH Press UP AND DOWN at the same time for 3”, until the screen moves UP AND DOWN

References

• Schermi per la videoproiezione - Screenline Srl
• Schermi per la videoproiezione - Screenline Srl

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>