SCREENLINE 16-9EL400-SL-IC390D-GH 16:9 Inceiling Screen with FlatVision Surface Instructions
- June 12, 2024
- SCREENLINE
Table of Contents
INCEILING & **INCEILING TENSIONED
Instructions**
16-9EL400-SL-IC390D-GH 16:9 Inceiling Screen with FlatVision Surface
WARNING! BEFORE STARTING WITH THE INSTALLATION IN-CEIUNG, TEST THE FUNCTIONALITY OF THE MOTOR, THE PLANARITY OF THE FABRIC AND GENERALLY CHECK THE PROPER FUNCTIONING OF THE SCREEN.
INCEILING – INCEILING TENSIONED
| DESCRIPTION| WHITE| BLACK BORDERS| WHITE TENSIONED| BLACK TENSIONED
B| PROJECTION BASE| | | |
L1| COUNTERWEIGHT BASE| B+ 40mm| B+ 140mm| B+ 110mm| B+ 215mm
L2| HOLES DISTANCE| B+ 117mm| B+ 217mm| B+ 192mm| B+ 292mm
13| BRACKETS ENCUMBRANCE| B+ 145mm| B+ 245mm| B+ 220mm| B+ 320mm
L4| TOTAL ENCUMBRANCE| B+ 185mm| B+ 285mm| B+ 260mm| B+ 360mm
Attach the
adhesive stencil to the ceiling in the desired location. Proceed with cutting
the false ceiling. 
With the help of a laser or a sinker, find
the installation point of the brackets. Take the center point of the cut in
the ceiling as a reference. 75mm. 
Tilt the screen to help you install.
Screw the nuts
so that the screen reaches the correct height at the edge of the false
ceiling.
Electrical
installation must be carried out by qualifi ed personnel.
| TERMINALS | POWER SUPPLY | MOTOR (EUR) | MOTOR (US) |
|---|---|---|---|
| L | PHASE (L) | ||
| N | NEUTRAL(N) | BLUE | WHITE |
| W | EARTH (W) | YELLOW/GREEN | GREEN |
| 1 | BLACK OR BROWN | BLACK OR RED | |
| 2 | BLACK OR BROWN | BLACK OR RED |
- Disconnect the main supply before carrying out any work.
- Ensure that no forces act on terminals after installation.
- Connect the earth wires before phase and neutral.
GENERAL SAFETY NORMS
CAUTION: Important safety instructions. Follow the instructions as
improper installation can cause serious injury. Always read the instructions
and warnings set out in this manual very carefully before using the product or
before performing any maintenance interventions.
Installation of the screen above passageway is strictly forbidden. Before and
during use, check that the screen poses no risk of hazard.
Do not tamper with, remove or damage any part or component of the screen.
Never carry out maintenance work on the screen with the motor on and always
disconnect the power first.
Always disconnect the power when cleaning, carrying out maintenance or
replacing parts.
Not children safe. It is mandatory to keep children away during operations
with the screen.
All our screens are covered by guarantee; validity of the same shall be
subject to user’s full compliance with the instructions contained in this
manual.
WARNING: Faulty installation may compromise the safety of the product’s
operators; manufacturer shall not be held liable for damages to persons or
things resulting from faulty installation, improper use, insufficient or
inadequate maintenance of the screen. Manufacturer shall not be held
responsible for problems associated with installation errors.
Screen installation, electrical connections and verifications in case of
malfunction of motorised rolling screens must be performed by authorised
vendor or by personnel that is informed and trained in electrical hazards.
The connection cable cannot be replaced. If the cable is damaged the screen
must be replaced.
Tampering with the end stops shall entail the forfeiture of the guarantee. For
any necessary clarifications please contact our techni
WARNINGS AND RECOMMENDATIONS FOR CORRECT USE AND INSTALLATION
Our screens are suitable for indoor use at normal temperature (20 – 25 °C) and
humidity conditions.
It is absolutely forbidden to install the video projection screens in front of
windows or use them as blackouts exposed to direct sunlight near strong
sources of light, near heat sources, such as stoves, fireplaces or flues near
air conditioning systems, for both cold or warm air, failure to comply with
these prohibitions may cause deformation or permanent stretching of the
projection fabric.
PRODUCT’S DISPOSAL
As is the case for installation procedures, when the product reaches the end
of its useful life, disposal operations must be carried out by qualified
personnel.
The product is made up of various types of material: some can be recycled,
others have to be disposed of. You must follow applicable recycling or
disposal regulations in force in your area for this product category.
As shown in the picture on the left, you must not throw the product into a
domestic litter bin. Either dispose of the various components separately,
pursuant to the regulations applicable in your territory, or hand the product
over to a vendor upon purchasing asimilar new product.
Warning: local regulations can foresee heavy fines in case of unlawful
disposal of this product. Images contained in this manual are intended to
provide a detailed description of the product’s functions, characteristics and
procedures. Any slight difference, depending on the model.
GENERAL CHARACTERISTICS OF THE PRODUCT
The screen product is manufactured in compliance with the provisions of the
following EC directives:
2014-35-CE LDV Low voltage
2014-30-EU EMC Electromagnetic compatibility
2014-53-CE Radio Equipment
2009-125-CE CONSUMPTION Ecodesign
2011-65-CE ROHS Restriction of Hazardous Substances
2012-19-CE RAEE Waste management
2001-95-CE SAFETY Safe Product
The screen described in this manual must be used exclusively as a support for
video projection. Any other use not covered by this manual, it is not
consented.
The screen contains one or more Fabric/sheet of projection.The Fabric of
projection is a cadmium-free plastic pvc sheet plastified PVC impregnated, any
fabric can be classified in category:
- M1 and M2 fire classification under French standards
- B1 and B2 fire classification under German standards
- UL94HB fire classification under USA standards (THE GOVMARK Organization, Inc.)
In the absence of a standardisation at a European level of the various
national classification norms, it should be noted that the French M1 class
corresponds to non flammable material and that M2 class corresponds to flame
retardant material.
The screens use projection fabrics/sheets composed mainly of plasticized PVC
or fiberglass. As these fabrics are sensitive to temperature and humidity, the
acceptable size tolerance is 1% in each dimension. There is a tolerance of
+/-2 mm on the aluminium profiles used.
The tollerance on the overall size are:
- +/- 3 mm up to an overall size of 2500 mm;
- +/- 5 mm up to an overall size of 4000 mm;
- +/- 10 mm up to an overall size of 8000 mm;
- +/- 20 mm up to an overall size of 16000 mm;
- +/- 30 mm up to an overall size of 24000 mm.
GENERAL SAFETY NORMS
Screens and their projection surfaces are delicate and must be cleaned with
great care, according to the following instructions:
Never use solvents, chemical or abrasive products, or pointed tools to clean
the surface.
Avoid contact with other materials (varnishes, inks etc) as they might be
impossible to remove from the canvas.
GENERIC FABRIC: Clean the projection screen with a soft, clean, damp cloth,
and a neutral or base detergent as necessary. Since rubbing the screen with a
cloth during cleaning operations can cause electrostatic charge to accumulate,
we recommend the subsequent application of an antistatic liquid with a clean
cloth, to avoid dust being attracted again.
RADIANCE FABRICS: Clean the projection screen with a soft, clean, damp cloth,
and water. Do not use detergents. These fabrics are extremely delicated.
GENERIC PROFILE: Remove dust from the case with a soft, clean cloth and a non
aggressive detergent as necessary
VELVET PROFILE: Clean profile with a soft clean cloth, or a brush with soft,
antistatic bristles. A vacuum-cleaner brush may be used, provided its bristles
are soft and perfectly clean.
STRUCTURE and ANCHORING BRACKETS: The state of the product and the anchoring
capacity of its brackets must be checked regularly. In case of canvas
deformation or rips, or loosening of structural components such as brackets or
screws, action must be taken immediately to clear the area around the screen
and avoid hazard to people and things, replace the defective component and
restore the product’s functionality.
UNPACKING AND HANDLING THE SCREEN
Ensure that the screen has suffered no damage during transport. Should any
fault be detected, promptly notify your dealer.
Verify that all screen accessories have been included.
Warning: do not use cutters or sharp objects to open the wrapping, always use
protection gloves when unpacking, handling and installing the product.
Depending on the product’s weight (reference load: 25 Kg male – 15 Kg female),
handling and installing operations should be performed by two, three or four
people at least. For heavier loads we recommend the use of specific lifting
equipment.
WARRANTY
- GUARANTEE LIMITATIONS: The Manufacturer guarantees that all the products it distributes are free of production-, material- and processing-related defects, without prejudice to the following terms and conditions:
-
The product is guaranteed for a period of twenty-four (24) months as from the date of the purchase invoice/receipt released to the end user. 2. CONDITIONS AND LIMITATIONS: This guarantee is subject to the f ollowing conditions and limitations: the guarantee shall be deemed null and void if: the product has been used or manipul ated in any manner other than those indicated in the user manual’s instructions; or damaged as a result of improper use, or owing to accident or negligence during transport; or if the product’s defect is the result of repair or manhandling on the part of anyone other than personnel authorized by our Sales department.
The product must be installed by trained and experienced insider professionals, following the instructions provided for the installation and maintenance procedures.- RETURN: No product shall be returned and accepted without an authorization (RC) released by Sales department. Products must be returned in their original (or equivalent) packaging to avoid being damaged during transport.
Any transport damages resulting from inappropriate packaging shall not be covered by this guarantee. The returned product shall be accompanied by a detailed description of the defect and by a photocopy of the original purchase invoice/receipt.The purchase invoice/receipt shall clearly indicate the following: Model – Serial number – Purchase date – Name and address of the purchaser and authorized dealer.
- RETURN: No product shall be returned and accepted without an authorization (RC) released by Sales department. Products must be returned in their original (or equivalent) packaging to avoid being damaged during transport.
38060 Besenello (TN) Via Nazionale, 1/n – 1/u
+39 0464830003
info@screenline.it
screenline.it
Documents / Resources
|
SCREENLINE 16-9EL400-SL-IC390D-GH 16:9 Inceiling Screen with FlatVision
Surface
[pdf] Instructions
16-9EL400-SL-IC390D-GH 16 9 Inceiling Screen with FlatVision Surface,
16-9EL400-SL-IC390D-GH, 16 9 Inceiling Screen with FlatVision Surface,
Inceiling Screen with FlatVision Surface, Screen with FlatVision Surface,
FlatVision Surface, Surface
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>