SCREENLINE BT800H Big Lodo Evolution Instruction Manual

June 4, 2024
SCREENLINE

Big Lodo Evolution
Instruction Manual
SCREENLINE BT800H Big Lodo Evolution
-

Place the empty packaging in the installation room making sure that the screen is positioned with its front side in the right direction.

SCREENLINE BT800H Big Lodo Evolution - 01

Unpackaged the screen

SCREENLINE BT800H Big Lodo Evolution - 02 The installation must be carried out by qualified staff: the team in charge will have to unload, hoist and anchor the screen and connect the wiring.
The improper installation of the system may damage the motor and the control system. The installation not in compliance with the given instructions will nullify the warranty!
DURING THE HOISTING PROCESS IT IS STRICTLY FORBIDDEN TO WALK IN THE AREA UNDERNEATH THE SCREEN. ANY MISTAKE IN THE INSTALLATION OF THE SYSTEM COULD BE FATAL!
Any divergence from the procedures laid out in this manual will not be covered by the warranty.
SCREENLINE BT800H Big Lodo Evolution - fig 1SCREENLINE BT800H Big Lodo Evolution - fig 2

Wall brackets installation

SCREENLINE BT800H Big Lodo Evolution - fig 3SCREENLINE BT800H Big Lodo Evolution - fig 5

Install brackets according to the indication 400/600 mm.
The screws will be already in the correct position 400/600 mm. Install the part of the bracket that must be installed on the screen in the same position as the screws.

SCREENLINE BT800H Big Lodo Evolution - fig 6

Ceil brackets installation

SCREENLINE BT800H Big Lodo Evolution - fig 7

Screen installation

SCREENLINE BT800H Big Lodo Evolution - fig 8SCREENLINE BT800H Big Lodo Evolution - fig 9

In case of truss installation: Aliscaf brackets

SCREENLINE BT800H Big Lodo Evolution - fig 10

Remove the lower part of the bracket.

SCREENLINE BT800H Big Lodo Evolution - fig 11

See page 4 to install the lower part of the bracket to the screen

SCREENLINE BT800H Big Lodo Evolution - fig 12

Rotate the hook to open and close the bracket

Eyebolt bracket

SCREENLINE BT800H Big Lodo Evolution - fig 13

Remove the lower part of the bracket.

SCREENLINE BT800H Big Lodo Evolution - fig 14

See page 4 to install the lower part of the bracket to the screen

SCREENLINE BT800H Big Lodo Evolution - fig 15

Rotate the hook to open and close the bracket

Wall safety chains

SCREENLINE BT800H Big Lodo Evolution - fig 16

Regulation of the counterweight in order to flat the fabric. Just in case of waves.

SCREENLINE BT800H Big Lodo Evolution - fig 17

WARNING
The PVC fabric is very sensitive to heating. In a very hot environment, the fabric can be softer excessively and stretch down by altering the video ratio. You should absolutely avoid placing the screen in front of sunlit windows or above radiators, fireplaces, and stove of all kinds. The higher will be the heating absorbed by the screen, the higher will be the deformation of the surface which will assume an elongated shape with curved lateral edges.

SCREENLINE BT800H Big Lodo Evolution - fig 19

TERMINALS POWER SUPPLY MOTOR (EUR) MOTOR (US)
L PHASE (L)
N NEUTRAL(N) BLUE WHITE
W EARTH (W) YELLOW/GREEN GREEN
1 BLACK OR BROWN BLACK OR RED
2 BLACK OR BROWN BLACK OR RED

– Disconnect the main supply before carrying out any work.
– Ensure that no forces act on terminals after installation.
– Connect the earth wires before phase and neutral.

ELETTRONICO LIMIT-SWITCH PROGRAMMING UNIT

SCREENLINE BT800H Big Lodo Evolution - fig 20

INFERIOR LIMIT POINTS’ CHANGING
WARNING: When delivered, the motor is set on “working” mode. To change the set points it is necessary to proceed with the cancellation of the points set by the manufacturer.
IT IS ESSENTIAL NOT TO MODIFY THE DOWN LIMIT POINT SET BY THE MANUFACTURER OVER ± 10 CM.
(Otherwise, the warranty shall not apply)

  1. Open the screen to the middle position;

  2. CLEAR ALL ADJUSTMENTS
    (This can only be done using a double button that is not interlocked)
    Press UP AND DOWN at the same time for 8”, until the screen moves UP AND DOWN 2 times.

  3. ENTER PROGRAMMING MODE
    Press UP and DOWN simultaneously until the screen moves UP and DOWN Press UP and DOWN at the same time for 8”, until the screen moves UP AND DOWN 2 times.

  4. ADJUSTMENT OF THE DOWN LIMIT SWITCH
    Pressing DOWN, bring the screen to the down limit point
    Pressing DOWN, bring the screen to the down limit Press UP quickly, release and press RISE again for 3”, until the screen moves UP and DOWN.
    Press UP quickly, release and press RISE again for 3”,SCREENLINE BT800H Big
Lodo Evolution - fig 24

  5. STORAGE OF THE LIMIT SWITCH
    Press UP AND DOWN at the same time for 3”, until the screen moves UP AND DOWN

NOTE …………………………

Screenline Srl – Via Nazionale 1/n 38060 Besenello (TN) Italy
+39 0464 830003
www.screenline.it
info@screenline.it

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals