MINELAB 4901-0226-PL-1 Metal Detector User Guide

MINELAB 4901-0226-PL-1 Metal Detector

Product Information

This product is the GOL MONSTER 1000, manufactured by Minelab Electronics Pty Ltd. It has a 2 year limited warranty from the time of purchase. For further warranty information, please visit
www.minelab.com. The product can be registered online at register.minelab.com.

The GOL MONSTER 1000 is a radio equipment that operates in the frequency range of 43 to 46.8 kHz. It has a power output of less than -30 dBm. More information about the product’s compliance with regulations can be found at www.minelab.com/compliance.

Product Usage Instructions

1. To turn on the device, press the power button.
2. For auto noise cancel, refer to the control panel. Adjust the settings according to your preference.
3. To perform a factory reset, press and hold the reset button for 10 seconds.
4. When assembling the device, follow these steps:
   • Screw the mid, lower, and upper shafts together.
   • Check for washers.
   • Attach the armrest to the upper shaft.
   • Wrap the cable around the shaft and connect it to the control box.
   • Attach the control box to the upper shaft.
   • Connect headphones to the device.
5. For battery charging:
   • Ensure metal objects are kept away from the coil.
   • Connect the device for charging.
   • Wait until the battery is fully charged.
   • If an error occurs during charging, refer to the user manual for troubleshooting steps.
6. During usage, perform overlap sweeps and keep metal objects away from the coil.

For more detailed instructions and guidelines, please refer to the user manual provided with the product.

Control Panel

1. Gold Chance Indicator
2. Battery Level
3. Sensitivity Adjust (1-10)
4. Auto Sensitivity (11)
5. Auto + Sensitivity (12)
6. Error Indicator
7. Volume Adjust (1-6)
8. Detect Mode
9. Ground Balance
10. Power

Quick Start

1. Turn On
2. Auto noise cancel
3. Begin gold detecting

Assembly

1. Screw mid, lower & upper shafts together
   Check washers

2. Attach lower shaft to coil

3. Attach control box to upper shaft

4. Attach armrest to upper shaft

5. Wrap cable around shaft & connect to control box

6. Insert batteriesConnect headphones

Universal Shaft Adaptor

Embout de manche universel

Alternative plastic shaft or broomstick

1. Insert shaft into yoke
   Check washers

2. Follow steps 2–6 of Assembly

Battery Charging

Detecting Basics

• Overlap sweep
• Sweep level
• Keep metal away from coil
• Refill hole

Press and hold for 10 seconds

Factory Reset

WARRANTY TERMS
This product has a 2 year limited warranty from the time of purchase. Please refer to www.minelab.com for further warranty information. Register this product online at register.minelab.com

COMPLIANCE
Information to the User (FCC Part 15.105)

NOTE: Class B Devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

WARNING: Any changes or modifications not expressly approved by Minelab Electronics could void the user’s authority to operate this equipment.

EU declaration of conformity
Hereby, Minelab Electronics Pty Ltd declares that the radio equipment type GOL MONSTER 1000 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: www.minelab.com/compliance

RADIO FREQUENCY SPECIFICATION

www.minelab.com

Images and graphics shown are for illustration purposes only; product configuration and specifications may vary from those shown. | Minelab® and GOLD MONSTER 1000® are trademarks of Minelab Electronics Pty Ltd.

Minelab Electronics,
PO Box 35, Salisbury South
South Australia 5106

References

• Metal Detectors | Minelab Metal Detectors
• MINELAB - Register Your Minelab
• Metal Detectors | Minelab Metal Detectors
• StackPath

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>