WETEK SOLUCOES TECNOLOGICAS SA HV50A FPC Antenna Instruction Manual
- June 1, 2024
- WETEK SOLUCOES TECNOLOGICAS SA
Table of Contents
WETEK SOLUCOES TECNOLOGICAS SA HV50A FPC Antenna
Product Information
Specifications
- Product Number: AN2450-FPC16GX
- Product Name: FPC Antenna
- Manufacturer: Tengxiang Technology.Inc
- Frequency: 2400-2500MHz / 5150-5850 MHz
- S.W.R.: (Specification missing)
- Cable Length: 130mm
Product Usage Instructions
Installation
- Locate a suitable mounting location for the FPC antenna.
- Ensure the antenna is positioned away from obstructions for optimal signal reception.
- Connect the FPC antenna cable to the appropriate device or connector.
- Secure the antenna in place using mounting hardware if provided.
Usage
Once installed, the FPC antenna can be used to enhance wireless signal
reception in the specified frequency ranges. Ensure proper connection and
positioning for optimal performance.
Maintenance
Regularly check the antenna connection and cable for any signs of damage.
Clean the antenna surface gently if needed to maintain signal quality.
FAQ
-
Q: What should I do if the antenna cable is too short?
A: If the cable length is insufficient for your setup, consider using a suitable extension cable to reach your device. -
Q: Can the FPC antenna be used outdoors?
A: It is recommended to use the FPC antenna indoors or in sheltered outdoor areas to protect it from environmental damage.
Specification
A. Electrical Characteristics
Frequency| 2400-2500MHz / 5150-5850 MHz
S.W.R.| <= 2.0 <= 2.5
Antenna Gain| 3.25dBi / 4.17dBi
Polarization| Linear
Impedance| 50 Ohm
B. Material & Mechanical Characteristics
Material of Radiator| Cu
Material of Plastic| FPC
Cable Type| 1.13mm gray
C. Environmental
Operation Temperature| – 40 ˚C ~ + 80 ˚C
Storage Temperature| – 40 ˚C ~ + 80˚CCharacteristics and Reliability Test
Test Items| Test Condition and Procedure| Requirements
---|---|---
C1| S.W.R.| Set DUT on Network Analyzer; make individual calibration to test|
Directive DUT specification
C2| Antenna
Gain
| Set DUT on Antenna Chamber; make individual calibration to test| Directive
DUT specification
M1| Vibration| MIL-STD-202G, 201A
Amplitude: 0.03 inch (0.76mm); Freq: 10 to 55 Hz 3 directions; 2 hours for
each direction| 1. No Visual Damage
2. Frequency Tol.<= 5%
M2| Random
Drop
| Height: 1.5 Meter; 3 directions; 1 time for each direction| 1. No parts separated
2. Frequency Tol.<= 5%
---|---|---|---
M3| Solderability| MIL-STD-202G, 210F, cond. A
Solder iron: 350±10°C; Duration: 5 seconds
| 1. Mounted on PCB
2. No Visual Damage
M4| Terminal- Pull Test| MIL-STD-202G, 211A, cond. A
Holding with individual specification; force applied to axis of terminal
| 1. Directive DUT specification
2. Frequency Tol.<= 5%
M5| Terminal- Torque Test| MIL-STD-202G, 211A, cond. E
Holding with individual specification; applied clockwise and counterclockwise to the axis of terminal
| 1. Directive DUT specification
2. Frequency Tol.<= 5%
M6| Dimension| Inspection of dimension, color, material, package,
surface process
| Directive DUT specification
E1| Salt Spray| MIL-STD-202G, 101E, cond. B
Temp: 35°C; RH: >= 95%; NaCl solution: >= 5%; Time: 24 hours
| After 2 Hours Recovery
1. No Visual Damage
2. Frequency Tol.<= 5%
E2| Humidity| MIL-STD-202G, 103B, cond. B
Temp: 40°C; RH: >= 95%; Time: 48 hours
| After 2 Hours Recovery
1. No Visual Damage
2. Frequency Tol.<= 5%
E3| Thermal Shock| 1 Cycle: – 40°C (30 minutes) to + 80°C (30 minutes) Cycles: 24| After 2 Hours Recovery
1. No Visual Damage
2. Frequency Tol.<= 5%
E4| Life (High Temp.)| MIL-STD-202G, 108A, cond. A
Temp: 80°C; Time: 24 hours
| After 2 Hours Recovery
1. No Visual Damage
2. Frequency Tol.<= 5%
R1| RoHS| With Reference to IEC 62321:2008 with flow chart| Directive RoHS 2015/863/Eu
Antenna
S Parameter Test Data
Radiation Pattern Test Data
Mechanical Drawing
Address: No. 53, Shayong Road, Shatou, Chang ‘an Town, Dongguan City