SCANSTRUT PTM-R1 Tapered Radar Mast Installation Guide
- June 12, 2024
- SCANSTRUT
Table of Contents
SCANSTRUT PTM-R1 Tapered Radar Mast
Product Information
- Product Name: Tapered Radar Mast – PTM-R1/R2 & PTM-R1/R2-S40
- Model Number: 10DPT-SRM3-1
- Quantity: 1
- Additional Components:
- 10DPT-SRM3-2 x1
- Base Seal x1
- PTM-R1/2-S40 Top Plate
- 101817 IP Sealing Grommet x 2
- 60085 M8 S/S washer x4
- 60080 M8 Nylock x4
- 610825 M8x25 CSK x4
- 60068 M6 Nutcover x6
- 60621 M6x20 x6
- 60060 M6 Nylock x6
- 60065 M6 S/S Washer x12
- 101804 IP Sealing Grommet x 2
- 64004 M10 shoulder washer x4
- FLIR M100/200 Fastners
- 60068 M6 Nut cover x12
- 60060 M6 Nyloc Nut x12
- 60702 M6 Nylon Washer x 12
- 60065 M6 S/S Washer x 12
- 610625 M6x25 CSK x6
- 620620 M6x25 SKT x6
- Tools Required:
- 8mm Flat Head
- 13mm x 1
- 10mm x 2
- Manufacturer: Scanstrut Ltd.
- Address: 5 Darts Business Park, Clyst St. George, Exeter, Devon, UK EX30QH
- Contact: Tel: +44(0)1392531280, E-mail: sales@scanstrut.com
- Website: www.scanstrut.com
Product Usage Instructions
- Inspect the installation and assembly regularly for evidence of damage or loose parts.
- Ensure the product is designed specifically for the mounting of approved marine electronics under normal boating conditions.
- Follow the installation instructions provided below:
- Start by attaching the Base Seal to the designated area.
- Place the PTM-R1/2-S40 Top Plate on top of the Base Seal.
- Install the Tapered Radar Mast (PTM-R1/R2 & PTM-R1/R2-S40) according to the provided instructions.
- Use the specified fasteners (FLIR M100/200 Fastners) to secure the components together.
- Ensure proper sealing by using the IP Sealing Grommets (101817 and 101804) at designated locations.
- Use M8 S/S washers (60085) and M8 Nylock nuts (60080) to secure the assembly.
- Use M6 Nutcovers (60068), M6x20 screws (60621), M6 Nylock nuts (60060), and M6 S/S washers (60065) as required.
- Secure the assembly using M10 shoulder washers (64004) if necessary.
- Follow the additional instructions provided by FLIR M100/200 Riser Kit ONLY if applicable.
- Ensure a proper fit and secure the assembly using M6x25 CSK screws (610825), M6x25 SKT screws (620620), M6 Nylon washers (60702), M6 S/S washers (60065), and M6 Nyloc nuts (60060).
Tools Required
Mounting
Instruction
IMPORTANT
No liability is accepted for damage caused by incorrect installation.
The installation and assembly must be regularly inspected for evidence of
damage or loose parts.
Product has been designed specifically for the mounting of approved marine
electronics under normal boating conditions.
Scanstrut Ltd. 5 Darts Business Park, Clyst St. George, Exeter, Devon, UK
EX30QH Tel: +44(0)1392531280
E-mail: sales@scanstrut.com Website:
www.scanstrut.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>