MARANO Connect Fully Modular Aluminium Fencing System Installation Guide
- June 4, 2024
- MARANO
Table of Contents
MARANO Connect Fully Modular Aluminium Fencing System
CONNECT
| ID| Description| Size mm| Colour| Code|
---|---|---|---|---|---|---
1
|
6m Long Aluminium Board
|
6000 x 150 x 15
| Raw Finish| 76S006R|
Basalt Grey RAL 7012| 76S006A|
Oak Wood Effect| 76S006O|
Serengeti Sand RAL 1019| 76S006SS|
Light Sage RAL 7032| 76S006LS|
2
|
6m Long Top Cap
|
6000 x 9 x 15
| Raw Finish| 76S006TCR|
Basalt Grey RAL 7012| 76S006TCA|
Oak Wood Effect| 76S006TCO|
Serengeti Sand RAL 1019| 76S006TCSS|
Light Sage RAL 7032| 76S006TCLS|
3
|
Marano Aluminium Angle – 1.8m Long
|
40 x 20 x 1.5
| Basalt Grey RAL 7012| 76A001A18|
Black RAL 9005| 76A001B18|
Marano Aluminium Angle – 1.2m Long| 40 x 20 x 1.5| Black RAL 9005|
76A001B12|
4| Screws for Fixing Boards – BZP (x 100)| 4.2 x 12| Black Dacromet|
76SS4212DB|
5
| 1.8m Slimline Post for 1.2m (Concrete-In) and 1.2m (Bolt Down) Fence|
1800 x 48 x 51
| Anthracite Grey RAL 7016| 76DP12iA|
Galvanized| 76DP12i|
2.4m Slimline Post for 1.8m (Concrete-In)
|
2400 x 48 x 51
| Anthracite Grey RAL 7016| 76DP18iA|
Galvanized| 76DP18i|
6
| Bolt Down Foot (with nuts and bolts). For use with a fence no higher than 1.2m|
–
| Anthracite Grey RAL 7016| 76DPBA|
Galvanized| 76DPB|
7
| Concrete Screws| 75mm Long|
– –
| 5002HCS1275|
2
|
Zinc Plated Through Bolt| M12 x 100| 162412|
| Marano Slimline Post Touch Up Paint| –| Anthracite Grey RAL 7016|
29PC400SA|
|
Fence Board Touch Up Paint
|
–
| Basalt Grey RAL 7012| 29PC400SAG|
Serengeti Sand RAL 1019| 29PC400SS|
Light Sage RAL 7032| 29PC400LS|
Description| | Information
---|---|---
Drill
| |
Use 4mm drill bit to screw fence board to Slimline post. .
Aluminium Saw
| | Use a fine tooth aluminium saw with
a clean, sharp blade if you wish to cut the boards to length.
Sealant
| |
Fix top caps and angles to fence boards.
Bolt-Down
| | 4 x M12 bolts required to fix
each bolt-down post – see number 11 for depending on terrain.
Concrete-In
| |
Place 600mm into the ground.
- Bolt Down Option. Allow post centres of 1800mm.
- Concrete-In Option. Allow post centres of 1800mm.
- Pattern with the next aluminum board.
- Fix the top board to the top of the Slimline post.
- Allow no more than 70mm from the top of the fence to the screw center.
- Add aluminum angle to end if required. Join boards in the middle of a post
- using 4 x screws to connect boards. Optional: fix the flat bar to the front of the join with screws.
- Create a corner by using aluminum
- Concrete-In Posts
Concrete-In Posts
Overall Height mm| Ground Clearance mm| Concrete-In mm| Post Size
H x W x D mm
| ****
Code
---|---|---|---|---
1210| 10| 600| 1800 x 48 x 51| 76DP12iA or 76DP12i
1810| 10| 600| 2400 x 48 x 51| 76DP18iA or 76DP18i
Bolt-Down Posts
Overall Fence Height mm| Ground Clearance mm| Post Size
H x W x D mm
|
Code
---|---|---|---
1810| 10| 1800 x 48 x 51| 76DP18iA or 76DP18i
The bolt-down foot is not recommended for fence heights over 1.2m. Posts can easily be cut to size on site. Please note: Post center measurements are shown as a guide only. Whilst we do our best to advise and guide, it remains the responsibility of the installer to ensure the final installation complies with any current building regulations and is securely installed. As we have no knowledge of the location, ground type, or layout of your system, we would always advise customers to consider these factors and adjust as appropriate.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>