UNIKS R1D NON CONTACT AC Voltage Detector User Manual

User Manual
R1D NON CONTACT AC Voltage Detector

REGISTER YOUR PRODUCT
www.uniks.it
The registration of your products will allow you to stay in formed about news, take advantage of advantageous discounts dedicated to you for the purchase of accessories and products far your daily work.

Safety instructions

Warning
To avoid possible electric shock or persona! injury:

• Please use this tester strictly according to this instruction, otherwise, the protection function provided by tester may be affected.
• Do not use if the power indicator is not on.
• Before use, test on the known power to ensure that the product is good.
• When using this tester, there may still be voltage even if there is no sound or light alarm. The tester only indicates the effective voltage when the AC voltage produces an electrostatic field with sufficient strength. If the field strength is very low, the tester may not be able to detect it. The tester may be affected by the following factors, including, but not limited to: Shielded wire / cable. Thickness and type of insulation. Distance from the voltage source. Complete insulating. Differences in socket design, etc..
• Do not use if the tester is damaged or the tester is not working properly. Before use, check that the probe is cracked or broken. lf in doubt, please timely repair tester.
• Please do not apply the rated voltage above the mark on the tester.
• To test AC voltage above 30V, special care must be taken in case of electric shock.
• Comply with local and national safety regulations.
• Use proper protective equipment in accordance with local or national regulations.

Instrument description

1. Probe (NCV induction head)

2. Torch lamp

3. LCD display

4. The power key, with power indicator

5. Torch key

6. AC voltage detection range switching key with indicator light

7. The battery cover

8. strong voltage

9. Medium voltag

10. Weak voltage

11. Battery Low voltage

12. high voltag

13. AC symbol

14. high sensitivity

LCD has two kinds of backlight colors: “white” and “red”.
(White means no AC signal is sensed, red means AC signal is sensed)

Operation instructions

1. Tum on/ off tester
   Tum on: Press the power key greater than 1 second, the power indicator light is lit.
   Tum off: Press the power key, power indicator lights off.

2. Tum on/ off Torch
   Tum on: Press the torch key to turn on the torch.
   Turn off: Press the torch key, the torch turn off.
   If the torch doesn’t tum off, it will turn off automatically in about 5 minutes.

3. AC voltage detection
   When use this product, probe tester should insert into the power socket or close to the live wire.
   When the tester detectsAC voltage signal, LCD backlight will changes from white to red, and LCD screen will flash according to the voltage signal. At the same time, the buzzer sends out sounds in different frequency. When a weak AC signal is sensed, the LCD screen displays “ ” in two cells; when a strong AC signal is sensed, the LCD screen displays “ ” in four cells; when a very strong AC signal is sensed, the LCD screen displays “ ” in six cells.

4. Zero/live wire judgment
   Try to separate the two wires to be detected as far as possible, Then close the wire with the probe of the tester, If it is a socket, insert the probe into the socket, One of the strong signals detected by a tester is live wire, a weak or no inductive signal is zero wire.

5. Selection of AC voltage detection range
   The default AC voltage detection range: about 48-1000V0
   To change the voltage range to a bout 12-1000V. Press sensitivity bottom “ “, LCD display “HS”.
   To switch it back, press sensitivity bottom “ ” again, “HS” disappears on LCD, the tester detect voltage range 48-1 000V.
   When the tester delecls AC voltage signal exceeds about 36V, the LCD displays” “

6. Auto Power Off
   When the tester does not operate for about 5 minutes and the voltage signal is not detected, the tester will tum off automatically.

7. Low battery indication
   When the battery voltage is lower than about 2.7 V, LCD display flashing, Please repiace the battery in time, When the voltage is lower than about 2.6V, it will shut down automatically.

Battery replacement

As per the diagram below:

Battery rotation direction as indicated

1. Rotate the battery cover
2. Take out the used battery
3. Insert new batteries follow battery anode and cathode indication.

Warning: To avoid electric shock, do not use this instrument before the battery covar is replaced.

ASSISTANCE

WARRANTY CONDITIONS
This instrument is warranted against defects in materials and workmanship, in accordance with the generai terms and conditions. During the warranty period, defective parts can be replaced, but the manufacturer reserves the right to repair or replace the produci. If the instrument is to be retumed to the after -sales service or to a dealer transportation is berne by the customer. The shipment musi, however, be agreed. Attached to dispatch an explanatory note about the reasons of the instrument must always be inserted. Far shipping only use the originai packaging.
Any damage caused by the use of non-originai packing shall be charged to the customer. The manufacturer accepts no responsibility for damage caused to people or objects.
The warranty does not apply in the following cases:

• Repair and / or replacement of accessories and battery (not covered by warranly).
• Repairs made necessary because of a misuse of the instrument or of its use with no compatible devices.
• Repairs made necessary due to improper packaging.
• Repairs made necessary due to work carried out by unauthorized personnel.
• Modification of the instrument without the explicit permission of the manufacturer.
• Use not provided far in the specifications of the instrument or in the instruction manual.

The conteni of this manual may not be reproduced in any form without the permission of the manufacturer.
Our products are patented and their trademarks.
The manufacturer reserves the righi to change specifications and prices it this is due to technological improvements.

Specifications

AC voltage detection range|  About 12 ∼ 1000V
(Acousto-optic prompt)| About 48 ∼ 1000V
(Acousto-optic prompt)
---|---|---
Frequency| 50 Hz /60Hz
Alarm mode| Sound and light alarm
Torch| White LED illumination lamp
Auto power off| √
Low battery indication| √
Zero/live wire judgment| According to the signal strength, strong signal is live wire
NCV intensity| Selecting 3 types of sensitivity automatically (low, mid, high)
NCV intensity indicaton mode| To indicate weak, median, or strong voltage signal, the instrument uses different symble on screen and buzzer frequency.
Service temperature| 0∼40°C
Stcrage temperature| -10∼50°C
Altitude| <2000m
Security level| CE CAT. III 1000V /CAT. IV 600V
Power| 2x 1.5V AAA batteries
Size| 156mm x 20 mm x 20 mm
Weight| About 45g

UNIKS Srl
Via Vittori 57
48018 Faenza (RA) Italy
E-mail: info@uniks.it
Phone: +39 0546 623002
Fax: +39 0546 623691

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>