Lowe s A04971P5 5-Light Matte Black and Polished Gold Modern Instruction Manual
- June 13, 2024
- Lowe s
Table of Contents
Lowe s A04971P5 5-Light Matte Black and Polished Gold Modern Instruction
Manual
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED)
Before starting assembly and installation please prepare the needed tools as below picture
-
Ladder
-
Philips Head or Flat Blade Screwdriver
-
**Electrical Tape
**
-
Pilers
-
Wire Cutter/Stripper
PARTS TYPE & QTY INCLUDING
-
(E) Stud (4)
-
(F) Mounting plate (1)
-
(G) Canopy (1)
-
(H) Strain relief (10)
-
(I) Cord (5)
-
(J) Upper cover (5)
-
(K) Thumbscrew (30)
-
(L) Metal strip (15)
-
(M) Ring (5)
-
(N) Glass shade (5)
ACCESSORIES & QTY ENCLOSED: -
(A) Anchor (4)
-
(B) Plastic Wire Connector (3)
-
(C) Wood screws (4)
-
(D) Mounting screw (2)
-
(O) Allen wrench (1)
-
(K) Screw (1) (Spare part)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position. Unscrew studs (E) from canopy (G) then gently remove mounting plate (F). Then set them aside for later installation
-
Unscrew studs (E) from canopy (G) then gently remove mounting plate (F). Then set them aside for later installation.
-
Adjust the length of cords (I) to achieve the desired height of the mounted fixture.
-
Use Allen wrench (O) to unscrew the screws in strain reliefs (H), carefully pull and push cords (I) through canopy (G) and strain reliefs (H) to lengthen or shorten the length of cords (I).
-
Once the desired height of fixture is achieved, carefully tighten the screw till snug.
-
Carefully pass the supply wires from the outlet box through mounting plate (F).
NOTE: To drill the holes on the wall for anchors (A), attach mounting plate (F) to the outlet box with mounting screws (D) and mark the holes.- Unscrew mounting screws (D) and remove mounting plate (F).
- Drill holes and gently knock anchors (A) into the holes until anchors (A) are level with the wall.
- Secure mounting plate (F) to the outlet box with mounting screws (D) and wood screws (C).
-
Make wire connections
Connect wires as below wires connection shown. REFER TO THE FOLLOWING CHARTS, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
Connect wires according to the below chart
*** Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
---|---
Black| White
Parallel cord (round & smooth)| *Parallel cord (square & ridged
Clear, Brown, Gold or Black without tracer| Clear, Brown, Gold or Black with tracer
Insulated wire(other than green) with copper conductor| Insulated wire(other than green) with silver conductor
|
- Twist wires together with plastic wire connectors until tightly joined.
- Wrap each connector with approved electrical tape.
- Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box
-
Position canopy (G) and mounting plate (F) in place, carefully thread studs (E) through the holes in canopy (G) and mounting plate (F).
Secure them by tightening studs (E).
-
Unscrew thumbscrews (K) from upper covers (J) and rings (M).
-
Pass thumbscrews (K) through the holes of metal strips (L), rings (M) and glass shades (N), then tighten thumbscrews (K) as shown in the illustration.
-
Pass thumbscrews (K) through the holes of metal strips (L) and upper covers (J), then tighten thumbscrews (K) as shown in the illustration.
-
Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
-
Check everything is already installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
+1 850 296 2377
Working hours : Mon – Fri 9:00 – 16:00 EST
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>