Lowe s A04965A 1-Light Matte Black and Polished Gold Drum Instruction Manual

Lowe s A04965A 1-Light Matte Black and Polished Gold Drum

Product Information

• Item Number: A04965A
• Working Hours: Mon – Fri 9:00 – 16:00 EST
• Contact Number: +1 850 296 2377
• Email: homecustomercare@outlook.com

Product Usage Instructions

1. We suggest installation by a licensed electrician.
2. Read the instruction carefully and save it for future reference.
3. Before starting any work, always shut off the electricity.
4. Ensure the mounting surface is clean, dry, flat, strong enough, and 1/4 larger than the canopy on all sides. Correct any gaps exceeding 3/16.
5. Check if the ceiling or wall can support the weight of the lamp before installation.
6. Make sure to use a voltage of 120V. The maximum wattage for LED bulbs is 20W.
7. Avoid contact with acidic and alkaline substances to prevent damage to the lamp’s surface.
8. When replacing bulbs, turn off or unplug the lamp and wait until it cools down.
9. Use common sense, caution, and care when handling electrical products.

Tools Required

• Ladder
• Philips Head or Flat Blade Screwdriver
• Electrical Tape
• Pliers
• Wire Cutter/Stripper

Parts Included

• (A) Mounting plate – 1
• (B) Green ground screw – 1
• (E) Stud – 2
• (F) Canopy – 1
• (G) Lock nut – 4
• (H) Steel Wire – 3
• (I) Cable – 1
• (J) Body assembly – 1
• (K) Crystal hook – 53
• (L) Crystal – 53

Accessories Included

• (C) Plastic wire connector – 3
• (D) Mounting screw – 2
• (K) Crystal hook (spare part) – 2
• (L) Crystal (spare part) – 2

Assembly & Installation Instructions

1. Remove the fixture from the carton and check that all parts and accessories are included.
2. Turn off the power before starting the installation.
3. Remove the mounting plate (A) using the mounting screws (D).
4. Connect the wires according to the provided wire connection chart. Note that the ground wire is a bare copper wire and should not be connected to other wires.
5. Connect the ground wires as indicated in the chart.
6. Connect the black or red supply wire to the outlet box ground using the green ground screw.
7. Connect the white supply wire to the fixture ground using the dimples and cupped washer.
8. Follow the additional wiring instructions based on the type of parallel cord being used.

Item Number: A04965A

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save them as you may need them at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home.
   • Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
4. The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is LED, 20W.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution, and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED

(NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING

• (A) Mounting plate (1)
• (B) Green ground screw (1)
• (E) Stud (2)
• (F) Canopy (1)
• (G) Lock nut (4)
• (H) Steel Wire (3)
• (I) Cable (1)
• (J) Body assembly (1)
• (K) Crystal hook (53)
• (L) Crystal (53)

ACCESSORIES & QTY ENCLOSED:

• C) Plastic wire connector (3)
• (D) Mounting screw (2)
• (K) Crystal hook (2) (spare part)
• (L ) Crystal (2) (spare part)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
2. Turn off power
   • Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home.
   • Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
3. Unscrew studs (E) from the canopy (F).
   • Remove mounting plate (A).
4. Attach mounting plate (A) to the outlet box with mounting screws (D)
5. Make wire connections
6. Connect wires as below wires connection shown.
   • PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
   • Connect ground wires according to the below chart
   • Connect wires according to the below chart
   • Twist wires together with plastic wire connectors until tightly joined.
   • Wrap each connector with approved electrical tape.
   •  Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
7. Raise canopy (F) to the ceiling and secure the canopy (F) in place by tightening studs (E) onto the preassembled screws in the mounting plate (A).
8. Hang crystals (L) to holes of body assembly
   • (J) with crystal hooks (K) as shown in the illustration.
   • To adjust the hanging height of the fixture:
   • Press down and hold lock nuts (G) by hand.
   • Pull or push steel wires (H) and cable (I) in and out of canopy (F) to increase or decrease the hanging height.
   • Please adjust steel wires first.
9. Check everything is already installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

• +1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST
• homecustomercare@outlook.com

Documents / Resources

| Lowe s A04965A 1-Light Matte Black and Polished Gold Drum [pdf] Instruction Manual
A04965A, A04965A 1-Light Matte Black and Polished Gold Drum, 1-Light Matte Black and Polished Gold Drum, Matte Black and Polished Gold Drum, Black and Polished Gold Drum, Polished Gold Drum, Gold Drum, Drum
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>