Lowe s Blobfish 3-Light Polished Gold Modern/Contemporary LED Dry rated Chandelier Instruction Manual
- June 13, 2024
- Lowe s
Table of Contents
Lowe s Blobfish 3-Light Polished Gold Modern/Contemporary LED Dry-rated
Chandelier
Product Information
- Item Number: A04970C3
- Maximum Wattage: Type B, Max 40W per bulb
- Voltage: 120V
- Contact Number: +1 850 296 2377
- Working Hours: Mon – Fri 9:00 – 16:00 EST
- Email: homecustomercare@outlook.com
Product Usage Instructions
- We strongly recommend installation by a licensed electrician.
- Read the instruction carefully and save it for future reference.
- Before starting any work, always shut off the electricity.
- Ensure that the mounting surface is clean, dry, flat, and strong enough to support the product. It should also be 1/4 larger than the canopy on all sides. Correct any gaps exceeding 3/16 as required.
- Check if the ceiling or wall can withstand the weight of the lamp before installation.
- Use only 120V voltage and Type B bulbs with a maximum wattage of 40W per bulb.
- Avoid exposing the lamp to acidic and alkaline substances, as they may damage the surface.
- When replacing bulbs, turn off or unplug the lamp and wait until it cools down.
- These safety instructions do not cover all possible conditions. Use common sense, caution, and care when dealing with electrical products.
Tools Required
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
Parts Include
- (C) Single bar – 1
- (D) Green ground screw – 1
- (E) Canopy – 1
- (F) Collar ring – 1
- (G) Collar loop – 1
- (H) Quick link – 2
- (I) Chain – 1
- (J) Loop – 1
- (K) Stem – 1
- (L) Arm assembly – 1
- (M) Arm – 3
- (N) Socket – 3
- (O) Glass shade – 3
- (P) Socket ring – 3
Accessories Included
- (A) Wire connector – 3
- (B) Mounting screw – 2
Assembly and Installation Instructions
- Remove the fixture from the carton and ensure all parts and accessories are included.
- Make pre-installation adjustments using chain pliers and discard any unwanted parts.
- Turn off the power before starting the installation.
- Install the fixture using the provided mounting screws. Ensure the side of the single bar marked GND faces out.
- Adjust the collar loop on the single bar assembly until the desired secure length is achieved.
- Pass the fixture wires through the collar loop to the top of the pre-assembled threaded nipple and gently pull to ensure the wires are not stressed.
If you have any further questions or need assistance, please contact us during working hours at +1 850 296 2377 or email us at homecustomercare@outlook.com.
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. Place the wall switch in the “OFF” position.
- The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED): Before starting assembly and installation please prepare the needed tools as below picture
PARTS TYPE & QTY INCLUDING
- (C) Single bar (1)
- (D) Green ground screw (1)
- (E) Canopy (1)
- (F) Collar ring (1)
- (G) Collar loop (1)
- (H) Quick link (2)
- (I) Chain (1)
- (J) Loop (1)
- (K) Stem (1)
- (L) Arm assembly (1)
- (M) Arm (3)
- (N) Socket (3)
- (O) Glass shade (3)
- (P) Socket ring (3)
ACCESSORIES & QTY ENCLOSED
- (A) Wire connector (3)
- (B) Mounting screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Make pre-installation
Step A2 » By measuring, determine the correct number of links needed for
proper hanging height. Using the chain pliers, disconnect and discard the
unwanted part.
Step A3 » Attach quick link (H) to chain (I) and loop (J) on the top of
the stem (K).
Step A4 » Carefully weave the fixture wires through the chain (I) in and
out of every other link and stop just when you reach the top of the chain (I).
Gently pull the wires to ensure the wires are not stressed.
Turn off power
Before you start the installation, NEVER attempt any work without shutting off
the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
Make installation
Step B1 » Remove collar ring (F) from collar loop (G). Attach single bar
(C) to the outlet box with mounting screws (B).
Note: the side of the single bar (C) marked “GND” must face out.
Step B2 » Raise canopy (E) over collar loop (G) and screw collar ring (F)
to measure a proper position.
NOTE: canopy (E) should be snug against the ceiling and collar loop (G)
should be screwed with enough threads (no less than 6 threads) on the pre-
assembled threaded nipple for more secure hanging. If not, adjust the collar
loop (G) on the single bar assembly (C) by screwing the collar loop (G) in or
out of the single bar (C) until the secure length is achieved.
Step B3 » Pass chain (I) through collar ring (F) and then through canopy
(E).
Step B4 » Open quick link (H), attach quick link (H) to collar loop (G).
Close quick link (H).
Pass the fixture wires through the collar loop (G) to the top of the pre-
assembled threaded nipple and gently pull to ensure the wires are not
stressed.
Step B5 » If needed, shorten the length of fixture wires. At this point,
the remaining wire length measured above the single bar (C) is at least 6″.
Step B6 » Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS
BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
- Twist wires together with plastic wire connectors until tightly joined.
- Wrap each connector with approved electrical tape.
- Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step B7 » Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening collar ring (F) onto collar loop (G).
Step B8 »
- Remove socket rings (P) from sockets (N)
- Carefully place glass shades (O) to sockets (N), and then screw sockets rings (P) to sockets (N) to secure them.
- Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
- Check everything is already installed properly, then you could turn on the light. Enjoy!
ORDEaRING PARTS
Keep this sheet for future reference in case you need to order replacement
parts. All parts for this fixture can be ordered from the place of purchase.
Be sure to use exact wording from illustrations when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner
(such as mild and non-abrasive soap). Do not use abrasive materials such as
scouring pads or powders, steel wool or abrasive paper.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>