PELCO SXTE4-QF04-EBT Sarix Thermal Enhanced 4 Camera Instruction Manual

June 13, 2024
PELCO

Sarix Thermal Enhanced 4 Camera
Installation Manual
PELCO SXTE4-QF04-EBT Sarix Thermal Enhanced 4 Camera
Document number: C6732M
Publication date: 04/23

Legal Notices

©  2023, Pleco Corporation. All rights reserved. PELCO, the PELCO logo, PELCO are trademarks of  Pleco Corporation.Other names or logos mentioned herein may be the trademarks of their respective  owners. The absence of the symbols ™ and ® in proximity to each trademark in this document or at all is  not a disclaimer of ownership of the related trademark. Pleco Corporation protects its innovations with  patents issued in the United States of America and other jurisdictions worldwide (see www.pelco.com).
Unless stated explicitly and in writing, no license is granted with respect to any copyright, industrial  design, trademark, patent or other intellectual property rights of Pleco Corporation or its licensors.

Disclaimer

This document has been compiled and published using product descriptions and specifications available at the time of publication. The contents of this document and the specifications of the products discussed  herein are subject to change without notice. Pelco Corporation reserves the right to make any such  changes without notice. Neither Pleco Corporation nor any of its affiliated companies:

(1) guarantees the  completeness or accuracy of the information contained in this document; or
(2) is responsible for your  use of, or reliance on, the information. Pleco Corporation shall not be responsible for any losses or  damages (including consequential damages) caused by reliance on the information presented herein.

Pleco Corporation

www.pelco.com
C6732M
Revision: 1 – EN
20230412

Important Safety Information

This manual provides installation and operation information and precautions for the use of this device.
Incorrect installation could cause an unexpected fault. Before installing this equipment read this manual carefully. Please provide this manual to the owner of the equipment for future reference.
This Warning symbol indicates the presence of dangerous voltage within and outside the product enclosure that may result in a risk of electric shock, serious injury or death to persons if proper precautions are not followed.
This Caution symbol alerts the user to the presence of hazards that may cause minor or moderate injury to persons, damage to property or damage to the product itself if proper precautions are not followed.
Failure to observe the following instructions may result in severe injury or death.

  • Installation must be performed by qualified personnel only, and must conform to all local codes.

  • This product is intended to be supplied by a UL Listed Power Unit marked “Class 2” or “LPS” or  “Limited Power Source” with output rated 12 VDC or 24 VAC, 9 W min. or Power over Ethernet  (PoE) rated 48 VDC, 9 W min.

  • Do not connect directly to mains power for any reason.
    Failure to observe the following instructions may  result in injury to persons or damage to the  device.

  • Do not expose the camera directly to high levels of x-ray, laser, or UV radiation. Direct exposure  may cause permanent damage to the image sensor.

  • Do not install near any heat sources such as radiators, heat registers, stoves, or other sources of  heat.

  • Do not subject the device cables to excessive stress, heavy loads or pinching.

  • Do not open or disassemble the device. There are no user serviceable parts.

  • Refer all device servicing to qualified personnel. Servicing may be required when the device has  been damaged (such as from a liquid spill or fallen objects), has been exposed to rain or moisture,  does not operate normally, or has been dropped.

  • Do not use strong or abrasive detergents when cleaning the device body.

  • Use only accessories recommended by Pelco.

  • This device complies with EN 60529 IP66 and IP67 ratings.

Regulatory Notices

The following Sarix Thermal Enhanced 4 camera models should be installed by a trained professional  and should be installed in restricted access locations:

  • SXRE4-VF09-EBT (DTMLD53)
  • SXTE4-VF36-EBT (DTMLD53)
  • SXRE4-VF09-EBT-1 (DTMLD53)
  • SXTE4-VF36-EBT-1 (DTMLD53)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference  received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003 (B)/NMB-3 (B).
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant  to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful  interference in a residential installation.  This equipment generates, uses and can radiate radio frequency  energy and, if not installed and used in accordance with the instructions, may cause harmful interference    radio communications. However, there is no guarantee that interference will not occur in a particular  installation.  If this equipment does cause harmful interference to radio or television reception, which can  be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is  connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications made to this equipment not expressly approved by Pleco Corporation or parties authorized by Pleco Corporation could void the user’s authority to operate this equipment.
To meet the requirements of the EN 50121-4 Railway Applications Standard, use an external power  supply or POE injector that is also compliant with EN 50121-4. Please contact Pelco for assistance regarding supporting equipment.
To meet the requirements of the EN 50130-4 Alarm Systems Applications standard, use an external  uninterruptible power (UPS) supply.
This equipment contains a coin cell battery.  Risk of fire, explosion, and burns. Do not disassemble,  crush, heat above 100°C (212°F), or incinerate.
The use of EMC compliant support and auxiliary equipment with this device is required in order to fully  comply with the EMC regulatory standards.

Disposal and Recycling Information

When this product has reached the end of its useful life, please dispose of it according to your local  environmental laws and guidelines.
European Union:
This symbol means that according to local laws and regulations your product should be disposed of separately from household waste. When this product reaches its end of life, take it to a collection point designated by local authorities. Some collection points accept products for free. The separate collection and recycling of your product at the time of disposal will help conserve natural resources and ensure that  it is recycled in a manner that protects human health and the environment.

Overview

Junction Box View

  1. Camera mounts
    Points for installing the camera to the junction box.

  2. Mounting hook slots
    Points to hold the camera to the junction box while connecting the required cables.

  3. Mounting holes
    Holes for securing the junction box to the mounting surface.

Front View

  1. Configuration panel cover
    Covers the configuration panel.

Side View

  1. PELCO SXTE4-QF04-EBT Sarix Thermal Enhanced 4 Camera - Side View Sun shroud
    An adjustable cover to help protect the lens against glare from the sun.

  2. Mount arm
    Adjustable mount arm for positioning the camera.

  3. Adjustment screws
    Provides a locking mechanism for the mount arm.

Rear View

PELCO SXTE4-QF04-EBT Sarix Thermal Enhanced 4 Camera - Rear
View

  1. Ethernet port
    Accepts power and Ethernet connection to the network. Server communication and image data transmission also occur over this connection.
    The camera can either be powered by Power over Ethernet (PoE) rated 48 VDC, or auxiliary  power rated 12 VDC or 24 VAC.

  2. Serial number tag
    Device information, product serial number and part number label.

  3. Camera mounting screws
    Screws for mounting the camera to the junction box.

  4. Mounting hooks
    Hooks to attach the camera to the junction box while connecting the required cables.

  5. Power and I/O cables
    Cables for connecting the camera to auxiliary power and I/O devices. For more information, see Connecting to Power and External Devices.

Configuration Panel View

  1. microSD card slot
    Accepts a microSD card for onboard storage. For more information, see (Optional) Configuring microSD Card Storage.

  2. Micro USB port
    Accepts a micro USB to USB adapter. Only required when using the USB Wi-Fi Adapter.

  3. Connection status LED indicator
    Green LED provides information about device operation. For more information, see Connection Status LED Indicator.

  4. Link LED indicator
    Amber LED indicates if there is an active connection in the Ethernet port.

  5. Firmware revert button
    Button can be pressed to revert the device to its factory default settings, see Resetting to Factory Default Settings.

Installation

Camera Package Contents

  • Pelco Sarix Thermal Enhanced 4 Camera
  • Junction box
  •  Mounting template sticker
  • 4 screws and anchors for solid walls
  • 4 screws for attachment to electrical box
  •  Protective rubber boot for Ethernet port
  • Teflon tape

Installation Steps

Mounting the Bullet Camera
If the cables for the camera will not be provided from inside the mounting surface, install the junction box first.  After you install the junction box, you can skip directly to step 3 of this procedure.

  1. Use the mounting template to drill four mounting holes into the mounting surface.

  2. Drill the cable entry hole into the mounting surface then pull the required Ethernet cable through the cable entry hole.

  3. Fasten the junction box to the mounting surface.    To prevent moisture from entering the junction box, it is recommended to apply teflon tape around  the threaded conduit pipe at the cable entry point of the junction box. Ensure the other two conduit  plugs are fully tightened.

  4. Insert the mounting hooks on the rear of the camera into the mounting hook slots on the junction  box, then let the camera hang.  PELCO SXTE4-QF04-EBT Sarix Thermal Enhanced 4 Camera - mounting hooksBefore connecting any cables, ensure that the cable connections are properly protected from  moisture and corrosion. Make sure the protective cable boot is installed over the Ethernet port to  protect the connection from dust and moisture.
    If PoE is not available, the camera may be powered through the auxiliary power cable using either  12 VDC or 24 VAC. For more information, see Connecting to Power and External Devices.

  5.  If there are external input or output devices that need to be connected to the camera (for example:
    door contacts, relays, etc.), connect the devices to the camera’s digital I/O connector cables. For  more information see Connecting to Power and External Devices.
    It is recommended that seal tape be applied around the external audio and I/O connection, if  necessary, to prevent moisture from entering.

  6. Install the protective cable boot.       a.  Thread one end of the Ethernet cable through the provided protective cable boot.
    Ensure the orientation of the cable and boot matches the one shown in the image.
    b.  Crimp the Ethernet cable onto the cord.
    c.  Plug the Ethernet cable into the camera’s Ethernet port.
    d.  After you connect the cable to the camera, slide the boot over the Ethernet port.

  7. Connect the network cable to the camera’s Ethernet port.    PELCO SXTE4-QF04-EBT Sarix Thermal Enhanced 4 Camera - etwork cable

  8. Tuck the extra lengths of cables into the cable entry hole or within the junction box compartment.

  9. Raise the camera until it covers the junction box.    PELCO SXTE4-QF04-EBT Sarix Thermal Enhanced 4 Camera -  cable entry

  10. Use the camera mounting screws to fasten the camera to the junction box.   

Removing the Configuration Panel Cover

  1. Use a T20 Pin-In star-shaped driver to unscrew the configuration panel cover.    
  2. Remove the cover from the configuration panel.

Initializing a Camera Username and Password
You must create a user with administrator privileges before the camera is operational.
The new user can be created using the following methods:

  • Camera’s web interface. Enter the camera’s IP address in a web browser to access the web  interface. For more information, see the Pelco Sarix Thermal Enhanced 4 Camera Operations   nual. If the camera is in the factory default state, you will be redirected to the New User page to  create an administrator user:
    1.  Enter a new User Name or keep the default administrator name.
    2.  Enter a new Password for the user. It is recommended to use a secure and complex  password.
    3.  Confirm the new password.
    4.  For the first user, Administrator must be selected in the Security Group drop-down menu.
    5.  Click Apply. After creating the user, you will be asked to login.

  • Camera Configuration Tool: discovered cameras that are identified by ****will require a first user to  be set. Select the Admin Users tab to create the first user. For more information, see the Camera Configuration Tool User Guide.

Note : Set up the first user through the camera’s Web Interface or Camera Configuration Tool before you connect the camera to a VMS.
(Optional) Using the USB Wi-Fi Adapter
If you have a USB Wi-Fi Adapter (USB-AC56-**-MSI), attach it to the camera’s micro USB port to access  the camera’s mobile web interface. After you connect to the Wi-Fi signal broadcast by the adapter, you can access the mobile web interface  from any mobile device using the following address: http://camera.lan
For more information about configuring the camera from the mobile web interface see Pelco USB Wi-Fi Adapter System User Guide.

The camera will reserve the 10.11.22.32/28 subnet for internal use while the USB Wi-Fi Adapter is  plugged in.
Assigning an IP Address
The device automatically obtains an IP address when it is connected to a network.
If the device cannot obtain an IP address from a DHCP server, it will use Zero Configuration Networking  (Zeroconf) to choose an IP address. When set using Zeroconf, the IP address is in the 169.254.0.0/16  subnet.
The IP address settings can be changed using one of the following methods:

  • The mobile web interface using the USB Wifi Adapter. For more information, see (Optional) Using the USB Wi-Fi Adapter.
  • Device’s web browser interface: http://cameraIP.address/.
  • Network Video Management software application.
  • ARP/Ping method. For more information, see Setting the IP Address Using the ARP/Ping Method.

Setting the IP Address Using the ARP/Ping Method
Complete the following steps to configure the camera to use a specific IP address:
Note: The ARP/Ping Method will not work if the Disable setting static IP address through ARP/Ping method checkbox is selected in the camera’s web browser interface. For more  information, see the Pelco Sarix Thermal Enhanced 4 Camera Operations Manual.

  1. Locate and make note of the MAC Address (MAC) listed on the Serial Number Tag for reference.

  2.  Open a Command Prompt window and enter the following commands:
    a.  arp -s For example: arp -s 192.168.1.10 00-18-85-12-45-78
    b.  ping -l 123 -t For example: ping -l 123 -t 192.168.1.10

  3. Reboot the camera.

  4. Close the Command Prompt window when you see the following message:  Reply from :

Accessing the Live Video Stream
Live video stream can be viewed using one of the following methods:

  • The mobile web interface using the USB WiFi Adapter. For more information, see (Optional) Using the USB Wi-Fi Adapter.
  • Web browser interface: http:///.
  • Network Video Management software application.

Aiming the Camera
Reference the camera’s live stream as you aim the camera.

  1.   Loosen the adjustment screw closest to the junction box to rotate the camera arm. PELCO SXTE4-QF04-EBT Sarix Thermal Enhanced 4 Camera -djustment screw
  2.   Loosen the center adjustment screw to tilt the camera. PELCO SXTE4-QF04-EBT Sarix Thermal Enhanced 4 Camera -center
  3. Loosen the adjustment screw on the camera to turn the camera body.    PELCO SXTE4-QF04-EBT Sarix Thermal Enhanced 4 Camera -oosen
  4. If the camera is turned sideways to look vertically at a scene, you can remove the sun shroud then re-install it to cover the camera’s new angle of view. PELCO SXTE4-QF04-EBT Sarix Thermal Enhanced 4 Camera - angle

(Optional) Configuring microSD Card Storage
To use the  camera’s SD card storage feature, you must insert a microSD card into the card slot.
It is recommended that the microSD card have a write speed of class 10 or better. If the microSD card  does not meet the recommended write speed, the recording performance may suffer and result in the  loss of frames or footage.

  1. Insert a microSD card into the camera. Do not force the microSD card into the camera or you may  damage the card and the camera.PELCO SXTE4-QF04-EBT Sarix Thermal Enhanced 4 Camera - Card Storage
  2. Access the camera’s web interface to enable the onboard storage feature. For more information, see the Pelco Sarix Thermal Enhanced 4 Camera Operations Manual.

Configuring the Camera
After the camera is installed, configure it using the instructions in the current version of the Pelco Sarix Thermal Enhanced 4 Camera Operations Manual.

Connecting to Power and External Devices

If PoE is not available, the camera may be powered through the auxiliary power cable using 12 VDC or 24 VAC. The power consumption information is listed in the product specifications. To power the camera, connect the two power wires to the  auxiliary power wires.  The auxiliary power wire is distinguished by its thicker wire gauge and AUX PWR label. The connection can be made with either polarity.
This product is intended to be supplied by a UL Listed Power Unit marked “Class 2” or “LPS” or  “Limited Power Source” with output rated 12 VDC or 24 VAC, 9 W min. or Power over Ethernet  (PoE) rated 48 VDC, 9 W min.
Power supplies and external devices are connected to the camera through the power and I/O wires.
For the locations of the power  and I/O connector blocks, see Overview.
The pinout for the I/O and power wires is shown in the diagram on the following page.PELCO SXTE4-QF04-EBT Sarix Thermal Enhanced 4 Camera -
Thermal

Example application.

  1.   Brown — Audio Input (line level) An external power amplifier should be used when connecting speakers and microphones, as shown in the diagram.
  2.  Yellow — Audio Ground
  3.  Green — Audio Output (line level)
  4.  Grey — Ground
  5.  Red — Digital Input
  6. Pink — Digital Output
  7.  Purple — Reserved Wire, do not connect.
  8. White — Reserved Wire, do not connect.
    • — Relay
    •** — Switch
    • M — Microphone
    • S — Speaker
    •AUX1 — Auxiliary Power Wire, labeled AUX PWR
    •AUX2 —  Auxiliary Power Wire

Connection Status LED Indicator

Once connected to the network, the green Connection Status LED indicator will display the progress in connecting to the Network Video Management software.
The following table describes what the LED indicator shows:

Connection State Connection Status LED Indicator Description
Obtaining IP Address One short flash every second Attempting to obtain an IP

address.
Discoverable| Two short flashes every second| Obtained an IP address but not connected to the Network Video Management software.
Upgrading Firmware| Two short flashes and one long flash very second| Updating the firmware.
Connected| On| Connected to the Network Video Management software.
The default connected setting can be changed to Off using the camera’s web user interface.  For more information, see  the Pelco Sarix Thermal Enhanced 4 Camera Operations  Manual.

Troubleshooting Network Connections and LED Behavior
For any of the below LED behaviors, ensure that the camera is getting power and is using a good network cable before trying another solution.

LED Behavior Suggested Solution
Green LED is off and amber is on Perform a factory reset of the camera using

the physical  firmware revert button. Resetting through the camera’s web interface will not produce the desired result.
Both LEDs are off and the camera is not connected or streaming video| Check the General setup page in the camera’s web interface to ensure the LEDs are not disabled.
If the LEDs are not disabled, perform a factory reset of the  camera using the physical firmware revert button.
Resetting through the camera’s web interface will not produce the  desired result.
Both LEDs are blinking several times at the same time, then pause and repeat the blinking| Perform a factory reset of the camera using the physical firmware revert button. Resetting through the camera’s web
interface will not produce the desired result.
A different LED blinking pattern than those described above| Perform a factory reset of the camera using the physical  firmware revert button. Resetting through the camera’s web  interface will not produce the desired result.

Resetting to Factory Default Settings

If the device no longer functions as expected, you can choose to reset the device to its factory default settings.
Use the firmware revert button to reset the device. The firmware revert button is shown in the following  diagram:

The firmware revert button in the Configuration Panel.

  1.   Ensure the device is powered on.
  2.  Using a straightened paperclip or similar tool, gently press and hold the firmware revert button.
  3.  Release the button after three seconds.

Do not apply excessive force. Inserting the tool too far may damage the camera.

For More Information

Additional information about setting up and using the device is available in the following guides:

  • Pelco Sarix Thermal Enhanced 4 Camera Operations Manual available on the Pelco website: www.pelco.com.
  • Camera Configuration Tool User Guide

Pelco Troubleshooting Contact Information

For further assistance, contact Pelco Product Support at 1-800-289-9100 (USA and Canada) or +1-559292-1981 (international).
Do not try to repair the unit yourself. Leave maintenance and repairs to qualified technical personnel only.

Pelco, Inc.
625 W. Alluvial Ave., Fresno, California 93711 United States
800-289-9100 Tel
800-289-9150 Fax
+1 559-292-1981 International Tel
+1 559-348-1120 International Fax
www.pelco.com
Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. ONVIF and the ONVIF logo are trademarks of ONVIF Inc. All other product names and services are the property of their respective companies. Product specifications and availability are subject to change without notice.
© Copyright 2023, Pelco, Inc. All rights reserved.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals