Bebe Stars 006 Car Baby Seat User Manual

: June 13, 2024
: Bebe Stars

006 Car Baby Seat

``

Your child’s safety depends on you. Proper product’s use cannot be assured unless you follow these instruction

CONGRATULATIONS!

Thank you for purchasing this safety car seat by Bebe Stars. We will always give you
the best products and service .
Please read the user manual before you use!

CUSTOMER SERVICE

If you experience a problem with this product or require assistance please contact
our local sales agent or contact our customer service department.

KNOW YOUR CAR SEAT

1.Carrying handle
2.Shoulder strap slots
3.Comfortable cushion
4.Adjuster(under the cover)
5.Harness adjuster strap
6.Shoulder strap
7.Chest pad
8.Buckle
9.Crotch pad
10.Adjuster cover
11.Diagonal belt guide
12.Harness connector
13.Lap belt guide
14.Adjuster button handle

INSTALLATION

assemble car seat

USAGE

Install position of the child seat in vehicle

wrong guide

Usage of buckle

Adjusting the shoulder strap height

Adjust and use the harness

Remove the crotch pad and buckle

IMPORTANT

SAFETY WARNING
For your child’s safety, please read these instructions carefully before use and keep them for future reference. Failure to follow the instructions contained in this manual could result in serious injury to your child.
This child seat can only be used with the harness for children less than 13kg in weight (group 0+), installed rearward facing using a three-point lap and diagonal seat belt.
This instrucon manual can be retained in the special space of the child seat for its life period.
Do not use this child seat in the home. It has not been designed for home use and should only be used in car.
Do not use any load bearing contact points other than those described in the instructions and marked in the child restraint.
Do not place rear-facing child seat on front seat with airbag. Death or serious injury can occur.
The child seat should be changed when it has been subject to violent stresses in an accident. • For the reason of safety, the child seat must be fixed inside the vehicle even if you do not put your child inside it.
Always make sure that any straps holding the seat restraint to adjust to the child’s body and check that the straps shall not be twisted.
Ensuring that any lap straps is worn low down, so that the pelvis is firmly engaged, shall be stressed.
Any luggage or other objects liable to cause injuries in the event of a collision shall be properly secured.
To prevent from the risk of fall, your child should always be fastened. It is dangerous to make any alteration or additions to the device without the approval of the competent authority, and a danger of not following closely the installation instructions provided by the child restraint manufacturer.
This child seat is designed for children from birth up to 13kg. Never overload the child seat more than one child or with other loads.
The child restraint must not be used without the cover.
The seat cover should not be replaced with any other than the one recommended by the manufacturer, because the cover constitutes an integral part of the restraint performance.
Before you adjust any movable or adjustable parts of your child seat, you must remove your baby from the child seat.
The child seat should be kept away from sunlight if the seat is not provided with a textile, otherwise it may be too hot for the child’s skin.
Never use a second-hand product, as you can never be certain what happened to it.

Never leave your child unattended!

INSTALLATION

This child seat can only be used with the harness for children less than 13kg in
weight (group 0+), installed rearward facing using a three-point lap and diagonal
seat belt.

Step 1. Put your child into the safety seat. Check the height of the shoulder straps are in the correct position and fasten the buckle. Then adjust the handle to the position 3 for carrying.
Step 2. Place the car seat on the vehicle’s seat. NOTE: Please ensure the car seat is in contact with the vehicle’s seat at point C – this will ensure the balance of A and B. Feed the lap second of the seat belt into the lap belt guide.
Step 3. Thread the diagonal belt second of the safety belt through the diagonal belt guide at the back of the car seat.
Step 4. Feed the other side of the lap belt into the other lap belt guide and fasten the safety belt. You will hear a “click” sound. Check the seat belt is correctly fastened by pulling the seat belt upwards.
Step 5. Adjust the handle to position 4. Ensure the seat belt is correctly routed and tighten the seat belt by pulling the diagonal belt upwards. Check that the webbing has not become twisted and also check that the cover is not impeding the movement or fit of the seat belt in any way.

USAGE

Install position of the child seat in vehicle

Correct fitting/suitable Incorrect fitting

This restraint is only suitable if the approved vehicles are fitted with 3 point with retractor safety-belts, approved to GB 14166 or UN/ECE Regulation No. 16 or other equivalent standards.
Important: The child seat must only be installed using a lap and diagonal seat belt.

? Not to use rearward-facing in seating position where an active frontal airbag is installed

? It can be installed in this position only if it is equipped with 3-point seat belts

Usage of buckle

Step 1. Put the two plastic seconds of the buckle together.
Step 2. Slot the two buckle connectors into the slot in the buckle until they “click” into place.
Step 3. Check the harness is correctly locked by pulling the shoulder straps upwards.

To release the harness, you can press the red button of the buckle inwards, the two plastic seconds will pop up.

Adjusting the shoulder strap height

Always check that the shoulder straps are at the correct height for your child. The child’s shoulder straps should always be threaded through the slots in the cover and seat shell that are closest to the top of your child’s shoulders.

• Step 1. Press the red button of the buckle downwards, the two metal seconds will pop up.

• Step 2. From the back of the seat pull the plastic seconds of the buckle through the cover and the seat shell.

• Step 3. Re-thread the two plastic seconds through the seat shell and the cover and fasten the buckle.

IMPORTANT : Ensure both shoulder straps are at the same height and they are not twisted.

Adjust the handle

• The handle of the child seat can be adjusted in 3 positions. Simultaneously press the 2 red buttons on each side of the handle. Swing the handle to the desired position and release the buttons.

USAGE

Adjust and use the harness

1. Loosen the harness

The harness is slackened by pressing the adjuster (under the adjuster cover) on the front of the seat. Press down the adjuster as you grip the two shoulder straps with your other hand. Pull the shoulder straps towards you to loosen the harness.

2. Tighten the harness

Pull the shoulder straps upwards to remove the slack from the lap second of the harness then pull the adjuster strap until the harness is fully tightened. The harness should be adjusted as tightly as possible without causing discomfort to your child.

Remove the crotch pad and buckle

• Turn the harness locking clip on its narrowest end and thread it through the slot under the boom of the seat and then though the slot in the fabric cover. • The crotch pad and buckle as well as the harness straps can be removed.

MAINTENANCE & CLEANING

Daily maintenance

• In daily use, check periodically the child seat. The child seat should be replaced after an accident.

• Please keep this child seat in dry and ventilated place to avoid damp moldy.

• If the child seat becomes dusty, clean the seat belt and the plastic pieces by swiping them with a damp sponge and let it dry under ambiance.

• If food or drink drop accidentally on the buckle, disassemble the seat belt from the child seat and rinse it gently by warm water. Leave it dry under ambiance. • If you need to clean the whole cover, please refer to washing instructions.