FIAMMA Vent 40 Rooflight Instruction Manual

FIAMMA Vent 40 Rooflight

Package contents

Vent White| 04328B01-|
---|---|---
04329B02-| 2,8 kg
Vent Crystal| 04328B01D
04329B02D

Tools Required

Dimension

Check that nothing has been damaged or deformed during transport. In the event of doubts or questions concerning the installation, use or limitations of the product, contact the dealer. We recommend that the installation is carried out by qualifi ed personnel and in compliance with current local regulations.

Installation Instructions

STANDARD

OPTIONAL – KIT EXTENSION VENT Ivory – Item No. 98683-116 White – Item No. 98683-112

OPTIONAL – KIT EXTENSION VENT Ivory – Item No. 98683-116 White – Item No. 98683-112

1. Decide where the roofl ight should be installed and make a square hole of 39cm. The roofl ight can be installed on roofs with thickness between 3 and 5cm. The optional Extension Vent kit must be used for fi xings with thicknesses greater than 5 cm up to max 8.5 cm.
2. Apply the waterproof sealant (recommended: SIKALASTOMER-710 / THEROSTAT II / DEKALIN 1512) in the lower part of the external frame. Clean the roof area perfectly.
3. Insert the outside of the roofl ight into the opening paying attention to turn the hinges in the direction of travel. Press lightly the external frame on the roof in order to distribute the sealant evenly, if necessary.
4. Fix it with 20 screws Ø4.2x30mm UNI EN ISO 7049 (not supplied)
5. Carefully siliconate all the perimeter of the external frame, fi ll any spaces between the roof and the frame and all the heads of the 20 screws. Insert the internal frame into the opening and fi x it with 4xØ3.5x15mm self-tapping screws UNI EN ISO 7049 (not supplied).
   Remove the protective plastic applied to the cover (do not expose the product to sunlight for too long to avoid to make this operation difficult).

Safety Instructions

SikaLastomer 710 TX Butyle Blanc

In case of problems please contact your local dealer. Consult our website for spare parts drawing..

Fiamma declines all responsibility for any personal injury and damage to property due to incorrect assembly or use of the product; it is suggested to keep the instructions inside the vehicle.
The assembly of the product must be carried out according to the assembly instructions: the product must not be modified in any way.
Before proceeding with assembly, check that the roof thickness is compatible with the product.
Before choosing the place where to assembly the rooflight, check that:

• The product doesn’t interfere with adjacent accessories (luggage racks, cables, reinforcements in the roof, cabinets inside the passenger compartment).
• the internal and external surface of the roof is flat.

Periodically check the tightness of all the screws in the rooflight, especially after the first kms from the installation and each time before and after long journeys.
Lubricate the lid opening device with a few drops of grease if it becomes hard.
If the opening-closing device hardens, lubricate the lid opening device with a few drops of grease It is forbidden to walk on the product’s cover.
Before starting the vehicle, check that the rooflight is properly closed.
Periodically check that the cover is intact.
Don’t open the rooflight when the vehicle is travelling Don’t open the rooflight in case of strong wind or rain. Remove snow or ice from the rooflight.
Always comply with speed limits and the Highway Code. The speed should always be suitable to traffic conditions and transported load.

CARE AND MAINTENANCE:

For the internal and external cleaning of the roofl ight, always use only neutral, non-aggressive detergents. For cleaning the Crystal cover use an acrylic glass cleaner with a soft cloth so as not to scratch the surface. Never use aggressive products such as glass cleaners, all-purpose cleaners, abrasives or dish-washing detergents.
Also, never use alcohol-containing detergents, solvents or any corrosive liquid.
The mosquito net can be cleaned with water and neutral detergent, removing the frame and the fi xing screws.

Accessories

EXTENSION VENT IVORY
Item No. 98683-116
EXTENSION VENT WHITE
Item No. 98683-112

THERMO VENT 40
Item No. 03650A01-

SPOILER UNIVERSAL
Item No. 06289-01-

ROLLO VENT 40
Item No. 06310-02-

Warranty Fiamma

In case of defects with regards to materials and manufacturing, the customer is entitled to the warranty in accordance with local laws and regulations of the country in which the product was purchased.

Customers Support

fiamma.com

Fiamma S.p.A. – Italy
Via San Rocco, 56
21010 Cardano al Campo (VA)

All rights reserved.
Fiamma S.p.A.
reserves the right to modify at any time,
without notice, prices, materials,
specifi cations and models or to cease
production of any model.

References

• amma.com
• Sika Aktivator 205 : Nettoie & Active le Support pour Mastic
• SikaLastomer 710 TX : Joint Étanche Lanterneau Van & Fourgon

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>