M5STACK OV2640 PoE Camera with WiFi User Guide

June 6, 2024
M5STACK

M5STACK OV2640 PoE Camera with WiFi

OUTLINE

M5Station is a general-purpose IoT workstation in the M5Stack development kit series. It integrates rich interfaces and peripherals and is highly expandable. Large space reserved inside, flexible customization, and more likely to be applicable to various industrial acquisition and control application scenarios.

SPECIFICATIONS

M5STACK OV2640 PoE Camera with WiFi fig 1.1

FUNCTIONAL DESCRIPTION

This chapter describes the ESP32-D0WDQ6-V3 various modules and functions.

CPU AND MEMORY
Xtensa®single-/dual-core32-bitLX6microprocessor(s), upto600MIPS (200MIPSforESP32-S0WD/ESP32-U4WDH, 400 MIPS for ESP32-D2WD):

  • 448 KB ROM
  • 520 KB SRAM
  • 16 KB SRAM in RTC
  • QSPI supports multiple flash/SRAM chips

STORAGE DESCRIPTION

External Flash and SRAM
ESP32 support multiple external QSPI flash and static random access memory (SRAM), having a hardware-based AES encryption to protect the user programs and data.

  • ESP32 access external QSPI Flash and SRAM by caching. Up to 16 MB external Flash code space is mapped into the CPU, supports 8-bit, 16-bit and 32-bit
    access, and can execute code.

  • Up to 8 MB external Flash and SRAM mapped to the CPU data space, support for 8-bit, 16-bit and 32-bit access. Flash supports only read operations, SRAM supports read and write operations.

CRYSTAL
External 2 MHz~60 MHz crystal oscillator (40 MHz only for Wi-Fi/BT functionality)

RTC MANAGEMENT AND LOW POWER CONSUMPTION

ESP32 uses advanced power management techniques may be switched between different power saving modes. (See Table 5).

  • Power saving mode
    • Active Mode: RF chip is operating. Chip may receive and transmit a sounding signal.
    • Modem-sleep mode: CPU can run, the clock may be configured. Wi-Fi / Bluetooth baseband and RF
    • Light-sleep mode: CPU suspended. RTC and memory and peripherals ULP coprocessor operation. Any wake-up event (MAC, host, RTC timer or external interrupt) will wake up the chip.
    • Deep-sleep mode: only the RTC memory and peripherals in a working state. Wi- Fi and Bluetooth connectivity data stored in the RTC. ULP coprocessor can work.
    • Hibernation Mode: 8 MHz oscillator and a built-in coprocessor ULP are disabled. RTC memory to restore the power supply is cut off. Only one RTC clock timer located on the slow clock and some RTC GPIO at work. RTC RTC clock or timer can wake up from the GPIO Hibernation mode.
  • Deep-sleep mode
    • related sleep mode: power save mode switching between Active, Modem-sleep, Light-sleep mode. CPU, Wi-Fi, Bluetooth, and radio preset time interval to be awakened, to ensure connection Wi-Fi / Bluetooth.
    • Ultra Low-power sensor monitoring methods: the main system is Deep-sleep mode, ULP coprocessor is periodically opened or closed to measure sensor data. The sensor measures data, ULP coprocessor decide whether to wake up the main system.

Functions in different power consumption modes: TABLE 5M5STACK OV2640 PoE
Camera with WiFi table 1

ELECTRICAL CHARACTERISTICS

LIMIT PARAMETERS
Table 8: Limiting valuesM5STACK OV2640 PoE Camera with WiFi table
2

  1. VIO to the power supply pad, Refer ESP32 Technical Specification Appendix IO_MUX, as SD_CLK of Power supply for VDD_SDIO.

WIFI RADIO FREQUENCY
Table 9: Wi-Fi RF characteristicsM5STACK OV2640 PoE Camera with WiFi
table 3

LOW-POWER BLUETOOTH RADIO

receiver
Table 10: Low-power Bluetooth receiver characteristicsM5STACK OV2640 PoE
Camera with WiFi table 4

launcher
Table 11: Characteristics of Low Power Bluetooth transmitterM5STACK
OV2640 PoE Camera with WiFi table 5

QUICK START

ARDUINO IDE

Visit Arduino’s official website(https://www.arduino.cc/en/Main/Software),Select the installation package for your own operating system to download.

  1. Open up Arduino IDE, navigate to File->Peferences->Settings

  2. Copy the following M5Stack Boards Manager url to Additional Boards Manager URLs:
    https://raw.githubusercontent.com/espressif/arduino- esp32/ghpages/package_esp32_dev_index.json

  3. Navigate to Tools->Board:->Boards Manager…

  4. Search ESP32 in the pop-up window, find it and click Install

  5. select Tools->Board:->`ESP32-Arduino-ESP32 DEV Module

  6. Please install CH9102 driver before use esp32 downloader kit burn the firmware: https://shop.m5stack.com/products/esp32-downloader-kit

M5STACK OV2640 PoE Camera with WiFi fig 2

BLUETOOTH SERIAL

Open the Arduino IDE and open the example program File->Examples->BluetoothSerial->SerialToSerialBT. Connect the device to the computer and select the corresponding port to burn. After completion, the device will automatically run Bluetooth, and the device name is ESP32test. At this time, use the Bluetooth serial port sending tool on the PC to realize the transparent transmission of Bluetooth serial data.M5STACK
OV2640 PoE Camera with WiFi fig 3

M5STACK OV2640 PoE Camera with WiFi fig 4

WIFI SCANNING

Open the Arduino IDE and open the example program File->Examples->WiFi->WiFiScan. Connect the device to the computer and select the corresponding port to burn. After completion, the device will automatically run the WiFi scan, and the current WiFi scan result can be obtained through the serial port monitor that comes with the Arduino.M5STACK
OV2640 PoE Camera with WiFi fig 5

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.
    • Reorient or relocate the receiving antenna.
    • Increase the separation between the equipment and receiver.
    • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
    • Consult the dealer or an experienced radio/TV technician for help.
      Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm etween the radiator & your body.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals