PAC RP4-NI13 RadioPRO Radio Replacement Interface Installation Guide
- June 13, 2024
- PAC
Table of Contents
- Introduction and Features
- Important Notes
- Wiring Connection Chart
- Illustration / Schematic
- Installation Steps
- Default Steering Wheel Control Programming
- Default SWC Button Assignments
- Optional Steering Wheel Control Programming
- Testing and Verification
- Product Updates (Firmware)
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
RP4-NI13
Radio Replacement and Steering Wheel Control
Interface for Select Nissan Vehicles
Introduction and Features
The RP4-NI13 interface allows the replacement of a factory radio in select
Nissan vehicles with MSCAN databus radios.
Using this interface will retain factory features, such as steering wheel
controls (SWC), reverse camera, and the factory amplifier, when the original
radio is removed. Use of this interface also allows you to program two radio
functions to each SWC button by using short press, long press dual command
functionality. The RP4-NI13 also provides outputs such as vehicle speed sensor
(VSS), illumination and *reverse trigger.
Important Notes
- These instructions apply to R.1.5.1.4 or later revisions. The revision info can be found on a small white sticker on the interface and packaging.
- The radio select rotary switch on the side of the interface, must be adjusted to the proper radio setting before plugging the interface into the vehicle (see next page for setting chart).
- The interface comes pre-programmed for all of the vehicle’s factory SWC functions, and does not require programming unless you wish to re-assign the SWC functions, or utilize short press, long press dual command functionality. The SWC can always be restored to default settings by pressing and releasing the program button on the side of the interface once, and waiting 7 seconds for the LED to flash 4 times.
- Does not retain 360 camera system.
Wiring Connection Chart
Vehicle Connector
| Yellow | Battery +12v |
|---|---|
| Black | Ground |
| Red | Accessory 12v+ (10 amp) |
| Pink | Vehicle Speed Output |
| Blue / White | Amp Turn On Input |
| Orange / White | Illumination Output (+) |
| Purple / White | *Reverse Output (+) |
| White | Front L + input |
| --- | --- |
| White / Black | Front L – input |
| Gray | Front R + input |
| Gray / Black | Front R – input |
| Green | Rear L + input |
| Green / Black | Rear L – input |
| Purple | Rear R + input |
| Purple / Black | Rear R – input |
| Yellow RCA | *Reverse Camera Output |
SWC Connector
| Blu/Yel | Kenwood, Newer JVC |
|---|---|
| 3.5mm Jack | Alpine, JVC, |
Clarion, Fusion,
Pioneer, Sony,
Boyo, Dual,
Lightning Audio,
Visteon or Advent
- Only available in vehicles equipped with a factory reverse camera.
Illustration / Schematic
Installation Steps
SET RADIO SELECT SWITCH
Alpine| JVC| Kenwood /
Lightning Audio| Clarion /
Nakamichi| Pioneer /
**Other*| Sony| Fusion**
---|---|---|---|---|---|---
1| 2| 3| 4| 7| 8| 9
*Other – Dual / Axxera, Jensen, Rockford Fosgate
Default Steering Wheel Control Programming
IMPORTANT! The interface comes pre-programmed for all of the vehicle’s factory SWC functions and does not require programming, unless you wish to re- assign the SWC functions, or utilize short press, long press dual command functionality. The SWC can always be restored to default settings by pressing and releasing the program button on the side of the interface once, and waiting 7 seconds for the LED to flash 4 times.
Default SWC Button Assignments
| Alpine| NC| Kenwood| Clarion| Pioneer| Sony|
Fusion
---|---|---|---|---|---|---|---
Volume +| Volume +| Volume +| Volume +| Volume +| Volume +| Volume +| Volume +
Volume –| Volume –| Volume –| Volume –| Volume –| Volume –| Volume –| Volume –
Source| Source| Source| Source| Source| Source| Source| Source
Track +| Track +| Track +| Track +| Search +| Track +| Track +| Track +
Track –| Track –| Track –| Track –| Search –| Track –| Track –| Track –
Enter| Voice| Voice| Voice| Voice| Voice| Voice| Power
Phone Answer| Receive| Receive| Off Hook| Send| Answer Call| Answer/End| Audio
Phone End| End| Reject| On Hook
–| End| End| Reject/Source| Mute
Optional Steering Wheel Control Programming
If you wish to re-assign the SWC functions, or utilize short press, long press dual command functionality, the interface must be programmed in the specific order shown on the chart below. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and release the program button on the side of the interface to skip that function. The LED will flash off and on, confirming that you have successfully skipped that function and are ready to proceed to the next one.
-
Turn the key to the ignition position.
-
Press and release programming button on the side of the interface.
-
Within 7 seconds, press the button that is to be learned on the steering wheel. The LED will turn off when the button is pressed. At this point you have two options:
A. For short press functionality: Release the button within 1.5 seconds. The LED will turn back on.
B. For long press functionality: Hold the button until the LED starts blinking. Release the button and the LED will go back to solid. -
If you need to program more buttons, repeat step 3 for each additional audio function on the steering wheel.
-
If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and release the program button on the side of the interface to skip that function.
-
Once programming is completed, wait seven seconds. The LED will flash three times, indicating end of programming.
-
Test the interface for proper functionality. Whenever a SWC is pressed, the LED on the interface should blink. If any function does not work, repeat the programming steps.
Optional Programming Order
| Alpine| NC| Kenwood| Clarion| Other’| Pioneer|
Sony| Fusion
---|---|---|---|---|---|---|---|---
1| Volume +| Volume +| Volume +| Volume +| Volume +| Volume +| Volume +|
Volume +
2| Volume –| Volume –| Volume –| Volume –| Volume –| Volume –| Volume –|
Volume –
3| Mute| Mute| ATT| Mute| Mute| Mute| Mute| Mute
4| Preset +| Source| Source| Source| Preset +| Preset +| Preset +| Source
5| Preset –| Track +| Play| Search +| Preset –| Preset –| Preset –| Track +
6| Source| Track –| Track +| Search –| Source| Source| Source / End Call|
Track –
7| Track +| Band / Disc +| Track –| Band| Track +| Track +| Track +| Audio
8| Track –| Preset / Disc –| Disc / FM +| Send / End| Track –| Track –| Track
–| Power
9| Power| Select| Disc / AM –| Send| Band| Band| Band|
10| Enter / Play| Attenuation| Answer| End| Answer | Phone Menu| Power / End
Call|
11| Band / Program| Phone Receive| Voice| Voice| End | Answer Call| Voice /
Answer / End Call|
12| Receive| Phone Reject| On Hook| | PTT | End Call| Voice(Android Auto
&Car Play) Answer / End Call **|
13| End| Voice| Off Hook| | | Voice| |
14| Voice| Power| Mute| | | | |
15| | | Preset +| | | | |
• Advent, Boyo, Dual, Lightning Audio, Jensen, Rockford Fosgate & Visteon •
Jensen & Advent ONLY • XAV-AX100 ONLY
Testing and Verification
- Turn the ignition on. The LED on the interface will turn on, and the +12v accessory wire will turn on.
- Turn on the radio and check balance and fade.
- Verify that all SWC are functioning properly.
- The LED and radio will turn off when the key is turned off.
Product Updates (Firmware)
The RP4-NI11 can be updated with new firmware as it becomes available, using
the PAC-UP interface updater (sold separately).
Please visit www.pac-audio.com/firmware
for available updates.
© 2022 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Rev: 1
Date: 9/14/2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>