FRICOSMOS 061452 Mobile and Autonomous Hand Wash Basin Instruction Manual

FRICOSMOS 061452 Mobile and Autonomous Hand Wash Basin

Product Information

• Input Voltage: 10-15 V DC / 20-30 V DC
• Output Voltage: 230 V AC
• Frequency: 50 Hz
• Power: 350 W (12V) / 300 W (24V)
• Maximum Power: 700 W
• Model Number: 061452

Product Usage Instructions

1. Before connecting the device, make sure it is not damaged.

2. Choose the appropriate cable for the power source (battery or lighter connection).

3. Connect the chosen cable with the 12V connection to the converter by attaching the cables to the terminals as shown in Fig.
   1. The red cable should be connected to the positive terminal (+), and the black cable should be connected to the negative terminal (-).

4. Adjust the temperature using the blue adjustment ring.

5. Plug in the resistance into the converter.

6. Fill the container with drinking water and insert the resistance through the bung hole, leaving only the crystal part submerged (refer to Fig. 2).

7. Plug the device into the power source.

8. To turn on or off, use the switch on/off (refer to Fig. 3).

9. If the setting scale does not correspond to the water temperature after a day or two of operation, recalibrate the heater by following these steps:

10. Switch off the heater and unplug it from the mains supply.

11. Measure the water temperature with an accurate thermometer.

12. Turn the indicator arrow (red) to point to the measured temperature.

13. Set the desired tank temperature with the temperature selector ring (blue).

14. Unplug the device for shutdown.

15. To clean the device, sterilize it before the first use of each day using a sterilizing product approved for drinking water. Use a damp cloth with neutral soap to clean, avoiding acids, harsh detergents, and scrubbing with steel wool or sharp objects.

Read the instructions before connecting the equipment and keep them in a safe place for reference.

CONTENTS & AVAILABLE SPARES

061450 – Optional resistance for mobile washbasin 34ºC-220v
461452 – Converter DC 12V AC 230V – 300W

SECURITY

• Developed for indoor use only
• Unplug the device before performing any maintenance operation.
• Do not clean the resistance until it is completely cold to avoid burns.
• If the cable of the resistance gets damaged, the whole set of cable-resistance must be replaced. Never replace only the cable.
• We recommend that you allow the mains cable to form a drip loop which ensures that water running along the cable cannot drip into de mains socket.
• Keep out of reach of children. This product is not a toy.
• This appliance is not intended for mentally, physically or sensory handicapped people, nor should they be used by persons without the necessary experience or knowledge, unless they are supervised by a responsible of security or instructed for using the device.
• Do not dispose this product as household waste. Take it to your local residues disposal point

INSTALLATION

• Before connecting the device verify that it did not suffer any damage.
• Choose the suitable cable to the electric current source which is available (battery or lighter connection)
• Plug the chosen cable with the 12V connection into the converter by attaching the cables to the terminals as shown in the table (Fig. 1)
  Color| Terminal
  ---|---
  Red| +
  Black| –
• Set the temperature with the adjustment ring (blue).
• Plug the resistance into the converter.
• Remove the plug
• Fill the container of drinking water and insert resistance through the Bung Hole submerged leaving only the part of Crystal.. Fig. 2

USE

Plug into the power source.
For turning on and off, operate the switch “on/off”(fig. 3)
Set the desired temperature by turning the adjustment ring (blue). If, after a day or two in operation the setting scale does not correspond to the water temperature, follow the following procedure to recalibrate the heater:
Switch off the heater and unplug it from the mains supply, measure the water temperature with an accurate thermometer, Turn indicator arrow (red) to point to the measured temperature. Set the desired tank temperature with the temperature selector ring (blue) Unplug for shutdown.

CLEANING

• Sterilized before the fi rst use of each day adding a sterilizing product approved for drinking water according to the instructions of the manufacturer. Realize this operation each day.
• Use a damp cloth (not soaked) with neutral soap.
• Do not use acids or harsh detergents or scrub with steel wool, scrapers, knives or sharp objects.

What in box

Usage Instruction

TECHNICAL

10-15 V DC

20-30 V DC

| 230 V AC| 50 Hz| 350 w (12V)

300 w (24V)

| 700W

Connection: lighter type 35A/15A

WARRANTY

The equipment is guaranteed for two years. Misuse of equipment eliminates the warranty. Excluded from the glass breakage warranty.

Indoor use only

Fricosmos, S.A. Polígono industrial nº 1, C/ C, 16-18. 28938 Móstoles (Madrid) – España

• Tel. (+34) 902 304 420
• Fax. (+34) 902 636 683
• Ref: 061450 y 061452
• www.fricosmos.com
• info@fricosmos.com
• Skype user: fricosmos

https://www.youtube.com/fricosmos

The partial or total reproduction of this document is strictlyp rohibited without the specific wrtitten authorisation of FRICOSMOS, S.A.
The information contained in this document may be modified or cnacelled without any obligation from FRICOSMOS, S.A. to notifyt i previously.

References

• Material para Hostelería y Comercio - Productos y Maquinaria
• FRICOSMOS - Professional stainless steel furniture for food trade equipment at the best prices on the market
• Material para Hostelería y Comercio - Productos y Maquinaria

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>