Clarke CON180 180mm Sander or Polisher Instruction Manual

CON180 180mm Sander or Polisher
**Instruction Manual

SANDER/POLISHER
MODEL NO: CON180
PART NO: 6462107

**

INTRODUCTION

Thank you for purchasing this CLARKE Sander/Polisher.
Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.
Your Sander/Polisher has been designed to give long and trouble-free service.
If, however, having followed the instructions in this booklet carefully, you encounter problems, take the unit to your local CLARKE dealer.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.
This guarantee does not affect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

**** Through the purchase of this product, the customer is taking on the obligation to deal with the WEEE in accordance with the WEEE regulations in relation to the treatment, recycling & recovery, and environmentally sound disposal of the WEEE.
In effect, this means that this product must not be disposed of with general household waste. It must be disposed of according to the laws governing Waste Electrical and Electronic Equipment (WEEE) at a recognized disposal facility.

GENERAL SAFETY RULES

CAUTION : FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY.
WORK ENVIRONMENT

1. Keep the work area clean and well lit. Cluttered and dark areas invite accidents.
2. Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids, gasses, or dust. Power tools create sparks that may ignite dust or fumes.
3. Keep children and bystanders away while operating a power tool.
   Distractions can cause you to lose control.

ELECTRICAL SAFETY

1. Power tools must match the power outlet. Never modify the plug in any way. Do not use adaptor plugs with earthed (grounded) power tools.
   Correct plugs and outlets will reduce the risk of electric shock.

2. Do not expose power tools to rain or wet conditions. Any water entering power tools will increase the risk of electric shock.

3. Do not abuse the electrical cable. Never use the cord for pulling or unplugging the power tool. Keep the cable away from sources of heat, oil, sharp edges or moving parts. Damaged or tangled cables increase the risk of electric shock.

4. When operating a power tool outdoors, use an extension cable suitable for outdoor use. Using the correct cable reduces the risk of electric shock.

PERSONAL SAFETY

1. Stay alert, watch what you are doing, and use common sense when you are operating a power tool. Do not operate a power tool when you are tired, ill, or under the influence of alcohol, drugs, or medication.

2. Wear personal protective equipment including eye protection. Safety equipment such as a dust mask, non-skid shoes, or hearing protection used for appropriate conditions will reduce personal injuries. Use a face or dust mask if the operation is particularly dusty. Wear ear protectors/defenders as the noise level of this machine can exceed 85dB (A). If working at floor level, always wear knee pads.

3. Do not over-reach. Keep your proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

4. Avoid accidental starting of the machine. Ensure the switch is in the off position and the locking button disengaged before plugging the machine in to the power supply. Carrying power tools around with your finger on the trigger or plugging in power tools that are switched on invites accidents.

5. Dress properly. Do not wear loose clothing or jewelry which may get caught in moving parts. Wear protective hair covering to contain long hair.
   For best footing, wear rubber-soled footwear. Keep the floor clear of oil, scrap wood, etc.

6. Concentrate on the job at hand, no matter how trivial it may seem. Be aware that accidents are caused by carelessness due to familiarity.

7. Switch the machine OFF immediately after the task is completed.

POWER TOOL USE AND CARE

1. Do not force the machine. Use the correct power tool for your application.
   It will do a better and safer job at the rate for which it was designed.

2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

3. Disconnect the power tool from the power supply before making any adjustments, changing accessories, or storing the tool. These measures will reduce the risk of the power tool starting accidentally.

4. Store power tools out of the reach of children and do not allow persons unfamiliar with these instructions to operate the power tool. Power tools are potentially dangerous in the hands of untrained users.

5. Maintain power tools in top condition. Keep tools/ machines clean for the best and safest performance. Check for misalignment or binding of moving parts, broken parts, or any condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use.
   Many accidents are caused by poorly maintained power tools.

6. Use recommended accessories. The use of improper accessories could be hazardous.

7. Machine cleanliness. Do not allow the ventilation slots in the machine to become blocked with dust.

8. Check the power tool for damage before using the machine. Any damaged part should be inspected to ensure that it will operate properly and perform its intended function. Check for alignment of moving parts, breakage of parts, mountings, and any other condition that may affect the machine’s operation. Any damage should be properly repaired or the part replaced. If in doubt, DO NOT use the machine. Consult your local dealer

ELECTRICAL CONNECTIONS

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAIN SUPPLY.

Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. Connecting it to any other power source may cause damage.
This product may be fitted with a non-rewireable plug. If it is necessary to change the fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or damaged, the plug must not be used until a suitable replacement is obtained.
If the plug has to be changed because it is not suitable for your socket, or due to damage, it should be cut off and a replacement fitted, following the wiring instructions shown below. The old plug must be disposed of safely, as insertion into the main socket could cause an electrical hazard.

WARNING : THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: BLUE =
NEUTRAL BROWN = LIVE

If the colors of the wires in the power cable of this product do not correspond with the markings on the terminals of your plug, proceed as follows.

• The wire which is colored Blue must be connected to the terminal which is marked N.
• The wire which is colored Brown must be connected to the terminal which is marked L. We strongly recommend that this machine is connected to the mains supply via a Residual Current Device (RCD)
  If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.
  **** This symbol indicates that this is a Class II product, and does not require an earth connection.

OVERVIEW & CONTENTS

When unpacking, check for damage or shortages etc. Any found should be reported to your CLARKE dealer where the product was originally purchased.
This CON180 sander/polisher is supplied with the following components:

• 1 x Handle
• 2 x Handle Fixing Bolts
• 2 x Washers
• 1 x 8 mm Hexagon Key
• 1 x 180 mm ‘Hook & Loop’ Backing Pad
• 1 x ‘Hook & Loop’ Wool Polishing Bonnet
• 1 x spare carbon brush
  

BEFORE USE

WARNING: MAKE SURE THAT THE TOOL IS SWITCHED OFF AND UNPLUGGED FROM THE MAINS SUPPLY BEFORE FITTING OR REMOVING THE HANDLE OR BACKING PAD.

FITTING THE HANDLE
The handle is recessed to fit onto the machine and is not adjustable, but can be fitted for left or right-handed use.

1.  Slot the handle onto the body of the machine, locating the lugs into the recesses in the machine body.
2. When the handle is in position, secure in position with the two hex screws supplied. Tighten using the hex key supplied. DO NOT overtighten.

FITTING THE BACKING PAD

1. Screw the backing disc onto the spindle.
2. Press and hold the spindle lock button and tighten the padded hand tight in a clockwise direction.
   • Either the polishing bonnet or a sanding disc can be fitted. See below. IMPORTANT: Never press the spindle lock button while the motor is running. Failure to observe this instruction can cause internal damage or lead to personal injury.

ATTACHING BONNETS AND SANDING DISCS
Align the bonnet or sanding disc carefully with the appropriate backing pad, pressing down to ensure a good grip.
Always ensure that the backing pad is clean as a build-up of dust & debris can result in damage to the hooks and loops.

OPERATION

Whether polishing or sanding, always ensure a loose workpiece is securely fixed, i.e. clamped to a workbench or secured in a vice.
When working on car bodywork, the vibration may cause any items left on the car bonnet, boot, or roof, to fall onto the rotating disc and be thrown, leading to injury to yourself or others in the work vicinity. Always keep the work area tidy.

1. Hold the sander/polisher firmly with both hands and switch it on. The motor will then run.

2. Push the trigger lock button forward and squeeze the trigger.

3. Adjust the speed control to the desired working speed.

4. Slowly apply the sander/polisher to the workpiece and proceed to sand or polish. Move the disc across the work applying a light even pressure. WARNING: ENSURE THAT THE WORKING POSITION ADOPTED DOES NOT CAUSE OPERATOR FATIGUE WHICH MAY LEAD TO LOSS OF CONTROL.

5. On completion, lift the sander/polisher from the work surface and release the trigger.
   WARNING: THE DISC WILL CONTINUE TO ROTATE FOR A FEW SECONDS AFTER THE TRIGGER HAS BEEN RELEASED.

6. Ensure the motor has come to a complete stop before setting the machine down on the workbench etc. Failure to do so can cause the machine to be thrown, resulting in damage to the machine or personal injury.

MAINTENANCE

WARNING : BEFORE COMMENCING ANY MAINTENANCE PROCEDURES, ALWAYS ENSURE THE SANDER/POLISHER IS ISOLATED FROM THE
ELECTRICAL SUPPLY BY SWITCHING OFF AND REMOVING THE PLUG FROM THE POWER SOCKET.

BEFORE USE

1. Always inspect the machine before use for any damage.
2. Ensure all fixing screws remain tight to ensure the tool is in safe working condition.
3. Inspect the power cable to ensure it is free from cracks or bare wires etc.

CLEANING

1. Ensure all air ventilation slots are clear, (Use compressed air to clean the tool if possible. Always wear protective goggles and a mask when cleaning with compressed air).
2. Clean the exterior of the machine with a soft cleaning cloth. Never use any chemicals or abrasives. Avoid using solvents when cleaning plastic parts, which may be susceptible to damage from commercial solvents.

GENERAL MAINTENANCE

1. Occasionally inspect the motor brushes and replace them if necessary after unscrewing the cover plate.
   • When removing brushes, note which way round they are. The brushes must be returned exactly as they are removed, DO NOT swap over positions, etc.

2. A pair of long-nosed electricians
   pliers will be required to remove and replace the brushes. Pull the connecting wire off the terminal. Lift up the retaining spring and carefully rest the spring on one side of the brush holder while changing the brushes.
   • All bearings etc, in this tool, are lubricated with sufficient high-grade lubricant for the machine’s lifetime under normal operating conditions, therefore no further lubrication is necessary.
   • Refer to your CLARKE dealer if internal maintenance is required.

FAULTFINDING

necessary.
Faulty switch.| Consult your Clarke dealer
Fuse blown.| Consult your Clarke dealer if necessary.
Faulty motor.| Consult your Clarke dealer
The motor runs but the pad does not rotate| Pad fastening is not engaged.| Press the drive lock button and tighten the pad.
The drive gear broke.| Consult your Clarke dealer
Heavy internal sparking| Faulty motor.| Consult your Clarke dealer
Motor becomes hot| Unduly heavy use.| Reduce the force applied to the tool. Let the tool do the work.
Air vents have become blocked.| Clean out the air vents using compressed air or clean them with a dry cloth.
Low supply voltage.| Ensure supply voltage is correct. If an extension cable is used, ensure it is of the correct rating and is fully unwound.
Excessive vibration| The disc is not mounted correctly.| Check and rectify.
Machine bearings are worn.| Consult your Clarke dealer

SPECIFICATIONS

Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice.

CONSUMABLE SPARE PARTS

Replacement bonnets and abrasive discs are available from your CLARKE dealer.
The Sander/Polisher Accessory Kit – CPK180 (Part No 3051995) includes:

• 1 x Foam Polishing Sponge
• 1 x Foam Rubber Backing Pad
• 1 x Rubber Backing Pad
• 1 x Synthetic Fleece Polishing Bonnet
• 1 x Wool Fleece Polishing Bonnet
• 3 x Sanding Discs (Grit 40, 60, 80)

PARTS LIST & DIAGRAM

DECLARATION OF CONFORMITY

|
---|---

A SELECTION FROM THE VAST RANGE OF

|

QUALITY PRODUCTS
AIR COMPRESSORS
From DIY to industrial, Plus air tools, spray guns, and accessories.
GENERATORS
Prime duty or emergency standby for business, home, and leisure.
POWER WASHERS
Hot and cold, electric and engine driven we have what you need
WELDERS
Mig, Arc. Tig and Spa. From 01Y to autoimdustial.
METALWORKING
Drills, grinders, and saws 101 0 IY and professional use. WOODWORKING
Saws. sanders, lathes, monism, and dust extraction. HYDRAULICS
Cranes, body repair kits, and tags for all types of workshop use.
WATER PUMPS
Submersible, electric, and engine drove for DIY, agriculture end industry.
POWER TOOLS
Angle grinders, cordless drill sets, saws, and sanders. STARTERS/CHARGERS
All sites for car and commercial use.

|

PARTS & SERVICE: 0208 988 7400
Parts Enquiries
Parts@clarkeinternational.com
Servicing & Technical Enquiries
Service@clarkeinternational.com
SALES: UK 01992 565333 or Export 00 44 (0)1992 565335
Clarke INTERNATIONAL
Hemnall Street, Epping, Essex CM16 4LG
www.clarkeintemational.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>