DLS PA6 6.5Inch 2 Way Coaxial Speaker User Manual
- June 13, 2024
- DLS
Table of Contents
PA6
6.5” 2-way coaxial speaker
User manual
DLS PERFORMANCE
PA 6
Welcome to DLS!
Thank you for buying a DLS Performance PA6. For us, it’s all about the sound
experience. We care deeply about sound and construction quality. In order for
your experience to be as optimal as possible, it is important that you read
this manual, preferably before you start your installation.
Keep the manual in a safe and accessible place for future reference.
Your speakers must be installed correctly in order to work as intended. Make
sure you have all necessary tools nearby before starting and that you are
completely confident in how to process. If you feel the slightest uncertainty;
feel free to take the help of an experienced installer or a car audio dealer.
Warranty
This coaxial speaker is covered by warranty, depending on the conditions in the country where it is sold. If the speaker is returned for service, please include the original dated receipt with the product.
General
Some sound systems may vary in size of the door speaker. Make sure that your vehicle has the same size as this speaker, before you start the assembly
DECLARATION OF CONFORMITY
DLS Performance speakers for vehicles are manufactured in accordance with the EU directive EEC 95/54 (72/245/ EEC) and are marked with the approval number. They are also marked in accordance with the WEEE-directive 2012/19/EC. The products are also produced in accordance with the EU RoHS directive 2015/863/EU.
DLS speakers are engineered by DLS Sweden, a part of:
Winn Scandinavia AB
Elementvägen 15 – SE-702 27 Örebro – Sweden
Tel: +46 19 20 67 65 – E-mail: info@dls.se
www.dls.se
Designed & Sound tuned in Sweden.
Included parts
Included products:
2pcs Coaxial speakers
Included in box:
2pcs Speaker cables 100cm
8pcs V-type clips
8pcs Screws
2pcs Grills
1pcs Manual
Pre installation
Disconnect Battery
Before you start the process of replacing speakers, disconnect and secure
the negative terminal from your battery/power source. This will prevent the
risk of damaging yourself or the products.
Place the disconnected terminal in a secure and isolated location away from
any possible connection belonging to the battery/power source system.
Installation
Mount the speakers in the door or in the rear shelf of your car. They may fit
in the factory pre-made mounting holes, if not you might have to modify the
fitting. If you want to improve the sound reinforcement you can use a baffle
of MDF-board or similar. An installation high up on the door side is to be
prefered. For door placements, there are normally speaker rings that have to
be used to make the speaker fit to the door panel.
NOTE! It is important to fasten the speakers properly in order to avoid
bad sound or rattling.
Door insulation
DLS recommends using insulation/sound deadening in the car doors. It lowers
the noise from the road/tires and prevent rattles and other noises from
plastic details in the doors.
If you need help deciding what type of door insulation you should use, ask
your DLS distributor for info and guidance.
Running-in time
Allow the speakers to play for at least 15-20 hours in order to perform at its
possibly best. This run-in can be made with tone sweep or with just music.
Start at a moderate volume and increase the volume step by step during the
running in period. After the 15-20 hour run in session the performance and
characteristics will be in the correct condition.
DLS support
For technical assistance, ask your car audio dealer where the product was sold or the distributor in your country. You can always contact the DLS Helpdesk in Sweden at e-mail: info@dls.se. Information can also be found on our WEB-site www.dls.se. We follow a policy of continuous advancement in development. For this reason, all or part of specifications & designs may be changed without prior notice.
Wiring diagram
Specifications
Art. no CC-PA6
| Woofer | 6.5” /165 mm |
|---|---|
| Basket | Steel |
| Magnet | HG Ferrite |
| Cone | Polypropylene |
| Tweeter | 0.51” / 13 mm |
| Frame | ABS |
| Magnet | Neodymium |
| Cone | Mylar |
| RMS Power | 50W |
| MAX Power | 100W |
| PEAK Power | 150W |
| Impedance | 4 Ohm |
| Sensitivity | 86dB 1W/1M |
| Freq. range | 67Hz-20 kHz |
Dimensions
Product markings
The crossed-out wheelie bin symbol means that the product, literature and
packaging included must be taken to separate collection at the end of their
working life. Do not dispose of these products as unsorted municipal waste:
take them for recycling. For info on your nearest recycling point, check with
your local waste authority.
This product has been granted with the CE certification mark to show that the
product follows the health, safety, and environmental protection standards for
products sold within the European Economic Area (EEA).
DLS products complies with the relevant provisions of the RoHS Directive for
the European Union. In common with all Electrical and Electronic Equipment
(EEE) the product should not be disposed of as household waste. Alternative
arrangements may apply in other jurisdictions.
DLS is a global partner of the European Mobile Media Association, an
organisation that focus on promoting the custom made mobile media
installations to consumers.
We follow a policy of continuous advancement in development. For this reason all or part of specifications & designs may be changed without prior notice. We reserve for possible typos, factual or numeric errors that may have been printed on any products, package designs, user manuals and/or other included accessories.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>