DEWALT DXF2410 Circulator Electric Fan Instruction Manual

June 13, 2024
Dewalt

DEWALT-LOGO

DEWALT DXF2410 Circulator Electric Fan

DEWALT-DXF2410-Circulator-Electric-Fan \(2\)

PRODUCT SPECIFICATIONS

Model DXF2410
Power 220-240V I 5016GHz I 190W
Speed Stepless Speed
Weight 15.5kg
Power cord H05W-F, 3C x 0.75mm2 I 3.6m

WARNING:

As with all electrical appliances, basic safety precautions should always be followed to reduce the risk of electric shock, fire, or injury to persons, including the following precautions

  • READ ALL THE INSTRUCTIONS BEFORE USING THIS FAN.
  • Use this fan only as described in this manual. Any other use not recommended by the manufacturer may cause electric shock, fire or injury to persons.
  • Do not operate the fan with a damaged power cord or after the fan malfunctions or has been dropped in any manner.
  • Use of extreme caution is necessary when any fan is used by or near children, disabled persons or pets and whenever the fan is left operating unattended.
  • Do not place the fan on a small, unlevel, uneven or any surface which might allow fan to tip or
  • For proper operation, fan should be placed on a smooth non-combustible, level surface.
  • Always unplug fan when not in use, when moving from place to place, when assembling or disassembling parts, and before cleaning.
  • The use of attachments that are not recommended or sold by the manufacturer may cause hazards.
  • Do not use
  • Do not use fan in window. Rain may cause electrical hazard.
  • Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
  • Do not run power cord under carpet. Do not cover cord with throw rugs, runners or the Arrange cord away from traffic area where it will not be tripped over.

READ&SAVE THESE INSTRUCTIONS

Shock Hazard

your fan only in dry environments. This fan is not intended for use in a bathroom, laundry area, or similar locations, or near sinks, washing machines, swimming pools or other sources of water. Never locate fan where it may fall into a bathtub or other water receptacle. Do not use in damp environments such

as flooded basements.

Hot Surfaces

not touch fan motor when in use. This motor is hot when in use, to avoid burns, do not let bare skin touch hot surfaces.

Fire Hazard

have arcing or sparking parts inside. Do not use near combustible materials or flammable gases or sources of heat. DO NOT USE in areas where gasoline, paint or flammable materials are used or stored. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock, fire, or damage the fan.

WARNING: Electrical Shock Hazard not use with damaged cord or plug. Use with adequate electrical system that is up to code.

To Prevent Electric Shock

  • connection of the equipment-grounding conductor can result in a risk of electric shock, check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded.
  • Do not modify the plug provided with the appliance-if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
  • WARNING: To Reduce The Risk Of Electric Shock
  • Do not use this product with any solid-state speed control device.

FAN OPERATION

  • Before assembling the fan, make sure sent. Compare parts with contents list.
  • If any part is missing or damaged, do not attempt to assemble, install, or operate the product. Contact customer service for replacement parts. Unplug
  • fan before assembling any parts to it.

Tools Required (Not Included}:

2 Phillips Screwdriver or Suitable Drill Equipped with #2 Phillips Bit.

Fan Cradle Assembly: Simple assembly is required to use this fan as shown in Fig. A .

  1. Foot frame
  2. Wheel
  3. Washer
  4. Screw
  5. Short screw
  6. Foot pad
  7. Screw nut
  • Put the 3 into the 4 , then thread the 4 into the 2 , align the threaded hole of the , , and tighten the 4

  • Remove the 6 of the s , align the upper and lower 6 with the mounting holes of the , , press the 1 with fingers, insert the s into the mounting holes of the lower 6 , and tighten the 5.

  • Fan Operation: Always operate the fan with the cradle in its upright The fan itself can be tilted into various positions depending on applications, including straight upward.

  • Fan Location: Place the fan in an area in the room that will provide the most effective air

  • Fan Connection: Plug fan directly into 230 volt C., 50Hz wall outlet. Be sure plug fits tightly in outlet. A loose connection may cause overheating and damage to the plug or fan. NOTE: To prevent overloading a circuit, do not plug the fan into a circuit that is servicing other electrical needs.

  • Turning Fan On: Place fan on stable level surface. Plug fan into properly grounded outlet. To start the fan, turn the switch from the OFF position to the desired fan speed.

  • Turning Fan Off: To turn the fan off, turn the switch from the current fan speed setting to the off position. Remove plug from outlet.

  • Adjusting Fan Tilt: Loosen the adjustment knob until the drum rotates freely on the frame. Adjust the fan to desired tilt angle and re-tighten the knob. Do not overtighten adjustment knob.

CARE and MAINTENANCE

Cleaning:

WARNING: Before cleaning the fan be sure to disconnect power cord from the plug. Clean the grill surface with a clean damp cloth. Do not use harsh chemical or abrasive cleaners.
WARNING: DO NOT IMMERSE THE FAN OR ANY WIRES IN WATER. Replace front grill before fan use and allow fan to dry completely before use. Periodic grill cleaning with a vacuum will prevent dust build up. The motor is sealed and does not require any interior maintenance, cleaning or lubrication.

Maintenance: The Internal motor bearings are permanently lubricated at the factory and do not require any additional lubrication.

Repair

WARNING: DO NOT OPERA TE THE FAN WITHOUT THE GRILL IN PLACE. DO NOT USE THE FAN IF IT HAS MALFUNCTIONED OR BECOME DAMAGED IN ANYWAY.

Storage: Keep original carton for storage of the fan. Coil and tie the power cord to avoid damage during storage.

Protecting the environment

Separate collection. Products and batteries  marked with this symbol must not be  disposed of with normal household waste.

Products and batteries contain materials that can be recovered or recycled reducing the demand for raw materials. Please recycle electrical products and batteries according to local provisions. Further information is available at www.2helpU.com\

OPTIONAL ACCESSORIES

WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this appliance could be hazardous. To reduce the risk of injury, only DEWALT recommended accessories should be used with this product.

TROUBLESHOOTING

WARNING:

  • TO REDUCE THE RISK OF INJURY FROM MOVING PARTS AND/OR ELECTRICAL SHOCK, TURN POWER SWITCH OFF AND DISCONNECT GROUNDED PLUG FROM ELECTRICAL OUTLET BEFORE PERFORMING TROUBLESHOOTING CHECKS.
  • Minor problems often can be fixed without calling customer service.
  • WARNING: If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Dewalt User Manuals

Related Manuals