Outwell 651157 ONS Light Unit Set Instruction Manual
- June 13, 2024
- Outwell
Table of Contents
Outwell 651157 ONS Light Unit Set
Product Information
The ONS Light Unit Set is an innovative camping accessory designed for use
with Outwell tents or awnings. This set includes various components such as a
remote control, light units, charging cables, and a hex key. The light units
feature LED beading and a USB C charge port for convenient charging.
The remote control allows users to easily operate the Outwell Nightlight
System, which offers three brightness levels. The indicator LED on the remote
indicates the status of the system.
Installation of the light units in the tent or awning is made simple with the
ONS pockets and light beading. The set screw can be used to secure the light
beading into the light unit if necessary.
Charging the light units is essential before first use. Troubleshooting tips
are also provided in case of any issues with the lamps or remote control.
Product Usage Instructions
Installation in tent/awning
- Locate the ONS pockets inside the tent or awning.
- Free the light beading from the retainer inside the pocket.
- Insert one ONS Light Unit into each pocket.
- Insert the end of the light beading into the opening of the Light Beading port (9) on the light unit until it reaches a stop inside.
- Ensure that the black part of the light beading sits just below the outer surface of the light unit head. Do not apply excessive force.
- If needed, use the set screw (10) to lock the light beading into place. Avoid overtightening and ensure that the set screw only touches the light beading.
Operating the Outwell Nightlight System
To operate the Outwell Nightlight System:
- Press the ON button (5) to switch on the light.
- Use the DIM button (6) to toggle between the three brightness levels.
- Press the OFF button (7) to switch off the light.
The light units will remember the last selected brightness level when turned off using the remote. When turned on again using the remote, they will start at the same selected brightness level.
Charging the light units
Prior to use, ensure that the light units are fully charged. Refer to section 3 of the instruction manual for detailed charging instructions.
Troubleshooting
If the lamps do not light up when switched on by the remote:
- Check if the light unit can be switched on using the operating button (11) located at the bottom of the light unit. If it doesn’t work, recharge the light units.
If the remote does not work and the indicator LED (8) does not flash when pressing the buttons:
- Replace the batteries in the remote. Refer to section 5 of the instruction manual for battery replacement instructions.
If the range of the remote has decreased or the buttons need to be pressed
hard to operate:
Please refer to additional troubleshooting steps in section 5 of the
instruction manual.
IMPORTANT
Read the instructions before using the appliance. Keep these instructions for
future reference
WARNINGS
- Do not stare into the operating lamp. This can be harmful to the eyes.
- The aluminum part of the light unit (silver-colored part) can get warm during, and after use, take care when handling the light units.
- When children are using the product, please ensure close supervision to reduce the risks.
- Please keep the product on a dry place to avoid rain, the risk of electric shock.
- Do not expose the product to fire or temperatures above 55°C, risk of explosion.
- Store the product in a cool and dry place, when not in use.
Product content
Overview of remote control
Overview of Light Unit
Overview of installation in tent/awning
Instructions for use
- The ONS Light Unit Set can only be used together with ONS compatible Outwell tents or awnings.
- The ONS Light Unit Set is required to use the Outwell Nightlight System on compatible tents or awnings.
- Before first use, make sure the light units are fully charged. See section 3.
Installation in tent/awning
- Place one ONS Light Unit in each pocket.
- Insert the Light Beading end into the opening of the Light Beading port (9) on the light unit, until the Light Beading reaches a stop inside the light unit. This means that the black part of the Light Beading will sit just below the outer surface of the light unit head. Do not use excessive force to install the Light Beading into the Light Beading port (9). Make sure the set screw (10) is backed out enough to allow the Light Beading to be inserted.
- If needed use the set screw (10) to lock the Light Beading into the light unit. Take care not to overtighten the set screw. The set screw should only just touch the Light Beading. In many circumstances, the Light
- Beading will stay in place, in the light unit, without tightening the set screw
Operating the Outwell Nightlight System
To operate the Outwell Nightlight System press the ON button (5) to switch on the light. Press the DIM button (6) to toggle between the three brightness levels. Press the OFF button (7) to switch off the light. The Light Units will remember the last selected brightness level when you switch them off by the remote. When you switch them on again, using the remote, they will start at that same selected brightness level.
Charging the light units
- Insert the USB C end of the charging cables (3) into the USB C charge port (13) on the light units. Connect the other end of the charging cables to a suitable USB power source.
- The charging LED (12) will light red when charging. It will change to green light, when fully charged.
- If desired, the light units can be charged while installed in the tent/awning. To do so, insert the charging cable (3) through the opening in the
bottom of the light unit pockets (16), and follow the charging instructions above.
Troubleshooting
Cleaning & maintenance
Visually check the general condition of the light units and the accessories on
a regular basis.
The light units and remote can be cleaned with a damp cloth if necessary.
WARNING : Do not use sharp or hard objects or cleaning agents for
cleaning as these may damage the product.
Replacing the remote batteries:
- Remove the three screws using a Philips 0 screwdriver.
- Lift the PCB (green part) with the battery holder out of the remote housing.
- Slide the black battery retainer out of the battery holder, using a fingernail
- Remove the two CR2016 batteries from the battery retainer and replace with new batteries. Observe the polarity of the batteries.
- Take care to dispose of the used batteries according to local regulations
Storage
If the light units are not used for a long time, they should be recharged
every 12 months.
Store the Light Unit Set in a cool and dry place.
Light Source: LED
The light source and control gear is not replaceable. Making the light source
and control gear replaceable would also introduce weak points in the
construction, that could reduce the lifetime of the product.
Instruction for disassembling when the product has reached the end of its usable life
All disassembly can be done with hand, no tools required. Unless otherwise noted.
-
Unscrew top part of aluminium head, counterclockwise
-
Remove bottom cap, twisting it gently clockwise until it comes loose with an audible click.
Gently remove it, observing not to damage the three-pin connector attaching it the to the upper inner circuit board -
Unscrew the lower part of the aluminium head containing the LED module, counterclockwise. Take care not to damage the wires.
-
Remove the two shell parts from each other, by gently pressing along the seams to release the tabs holding them together.
- Do not use excessive force.
- Do this on both seams.
Disposal
Light Units:
- Follow the disassembly instructions in section 8.
- Disconnect wires from circuit board by the white pin connectors.
- Remove outer circuit board from bottom cap by using Philips 0 screwdriver.
Remote:
- Follow the disassembly instructions in section 5.
- Dispose of batteries as battery waste.
- Dispose of circuit boards and LED module as electronic waste.
- Dispose of plastic parts as plastic waste.
- Dispose of aluminium parts as metal waste.
- All according to local regulations.
- Do not dispose of any batteries with general household waste.
Technical data
Light Unit:
- 3.7 V , 0.8A
- Battery type: Lithium-ion
- Battery: 3.7V 5.000 mAh
- Input: 5V , 1A
Remote:
- 6V , 10mA
- Battery type: 2 pcs CR2016
- IP44
- 433 Mhz
Outwell Customer Service
e-mail: info@outwell.com
Tel.: +45 70 50 59 00
Outwell® is a reg. trademark of Oase Outdoors
EU : Kornvej 9, DK-7323 Give, Denmark
UK : One Glass Wharf, Bristol, BS2 0ZX
outwell.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>