DNAKE DK250 Wireless Doorbell User Manual

DNAKE DK250 Wireless Doorbell

PRODUCT FEATURES

• 7″ TFT LCD display
• Video resolution: 800×480, with 15 frames per second
• Wide angle lens and LED for night vision
• Long standby door camera (battery or DC 12V)
• Waterproof door camera IP65
• Microphone and speakerphone
• Basic video intercom, monitoring, remote unlocking and tamper alarm feature
• Adjustable brightness and talking volume
• Support up to 2 door cameras and 2 indoor monitors
• Transmitting distance: up to 400m range in open area
• DIV installation to save labor cost

PACKACE CONTENTS

Please make sure the package contains the following items :

Contents of door camera

Contents of indoor monitor

PICTURES

Door Camera

Indoor Monitor

INSTALLING BATTERIES

Indoor Monitor
The rechargeable lithium battery {3.7V, 2500mA) comes with indoor monitor. Install the battery before use.

1.  Insert new battery as indicated, matching correct polarity{+,-).
2.  To replace the battery, slide the cover up until it snaps in place.

Notes:

1.  To activate battery please remove protective film from the battery prior to use.
2.  The battery needs to be replaced if it doesn’t recover its full storage capacities after recharging.
3.  When replacing the battery, make sure using good quality re-chargeable lithium battery. Never use other battery or conventional alkaline battery.

Door Camera

1.  Install two l.SV size C batteries (not supplied) into the battery compartment or connect with DC 12V power adapter to turn on the door camera.
2.  Drill four screws to fix the battery cover up.

INSTALLATION INSTRUCTION

Indoor Monitor

Charging Indoor Monitor
Important Note: Before initial operation, YOU SHOULD FULLY CHARGE THE INDOOR MONITOR for about 5 hours.

Installation Notes:

DIAGRAM

Note: The door camera can be powered by the batteries or the power adapter(not included}. Do not use batteries and power adapter. The monitoring feature is available by default when the door camera is powered by power adapter. If the door camera is powered by batteries, the monitoring feature is not available until the power mode is changed to power consumption mode (see page 21).

Door Camera

1.  After wiring from the connection terminal, tighten the cable. Drill the screws on the cable cover of the connection terminal.
2.  Choose a proper location for the door camera. Be sure to consider the average height of visitors. Drill screws to fix bracket on the wall. Hang the door camera on the bracket. Drill screws to fix door camera and finish the installation.

SETTINGS

Turning On
To turn on the indoor monitor, press and hold .
Powering on the indoor monitor, the system will enter into the following interface:

Note: When the battery power of indoor monitor is insufficient, it will display an indication icon 1 and emit warning tone. The indoor monitor will automatically turn off. You need to charge it.
Press on the indoor monitor, then the system will enter into the following interface:

Chapter 1: Volume

This function allows you to adjust  the volume (9 levels are adjustable) during a call.

1.  Press Up or Down to choose “Volume” menu, then press the button on indoor monitor.
2.  Press Up or Down to choose talking volume(9 levels are adjustable), and press Left or Right to adjust.
3.  Press Up or Down to choose ringtone volume(9 levels are adjustable), and press Left or Right to adjust.
4.  To set the ringing time, you can press Up or Down to choose Ringing Time(l-30 seconds are selectable), and press Left or Right to adjust.
5.  When setting Ringing Time at Os, indoor monitor is on mute.
6. . Press to save the settings and return to the previous menu.

Note: You can also press Left or Right  key to adjust the ringtone volume in standby mode.

Chapter 2: Brightness

This function allows you to adjust the brightness (9 levels are adjustable).

1.  Press Up e:.or Down to choose “Brightness” menu, then press .
2.  Press Left or Right to select the brightness level. Each time you press Left or Right , the indoor monitor displays with the selected brightness level .
3.  Press to save the settings and return to the previous menu.
   Note: You can also press Up or Down key to adjust the brightness in the standby mode.

Chapter 3: Key Tone

When the key is pressed, the indoor monitor acknowledges it with a key tone. Key tone can be disabled. In certain error conditions, there will be a warning tone when an incorrect key is pressed.

1.  Press Up or Down to choose “Key Tone” menu, then press .
2.  Press Up or Down to choose On or Off to enable or disable the function.
3.  Press to save the settings and return to the previous menu.

Chapter 4: Ring Tone

This function allows you to change the ring tone of indoor monitor (There are three ring tones for your selection).

1.  Press Up or Down to choose “Ring Tone” menu, then press to confirm .
2.  Press Upe:.or Down to select the ring tone . Each time you press Up or Down , the indoor monitor rings with the selected volume.
3.  Press to save the settings and return to the previous menu.

Chapter 5: Snap Set

1.  Press Up or Down to choose “Snap Set.” menu, then press .
2.  Press Up or Down to choose On or Off to enable or disable the function.
3.  Press to save the settings and return to the previous menu.

With this Auto Snap On, the camera will take a photo of visitor automatically when the visitor presses the Call button on the door camera. You can check this photo easily in the indoor monitor.

Notes:

1.  During the conversation, if you press the Snapshot key, the camera can take a photo of visitor and save it into the indoor monitor.
2.  During the monitoring, if you press the Snapshot key, the camera can take a photo of the view and save it into the indoor monitor.
3.  Up to 75 photos can be stored in the monitor. The previous ones will be removed automatically if the photos are more than 75 pieces in the indoor monitor.

Chapter 6: Snap Show

You can view or delete recorded photos in this menu. Door station number, missed call icon or the door camera’s PIR icon will be displayed at the top of photos correspondingly.

1.  Press Up c, or Down to choose “Snap Show” menu.
2.  Press@, and press Left or Right to view pictures.
3.  To delete the photo, press Left or Right to choose the photo and then press . The display will show “ “. Press to confirm.
4. This icon means Delete All. Pressing Unlock key, the system will prompt whether to delete all the photos. Press OK to delete and press Return to exit.
5.  After one warning tone, it will display next photo.
6.  Press to return to the previous menu.

Chapter 7: Date &Time

1.  Press Up or Down to choose “Date&Time” menu, then press to Select.
2.  To set the time, you can press Left or Right to choose the Hour or the Minute and press the Up or Down to adjust.
3.  To select the date, you can press Left or Right to choose the Year or the Month or the Date, and press the Up or Down to adjust.
4.  Press to save the settings and return to the previous menu.

Notes:

1.  Use 24-hour system as time format and DD-MM-YYYY as date format.
2.  Date & Time must be set in advance to ensure that the time displayed on the indoor monitor is correct.
3.  After replacing the battery, please set the time and the date again.
4.  The Date & Time setting order is Hour-Minute-Year-Month-Date.

Chapter 8: Door Set

1.  Press Up or Down to choose “Door Set.” menu, then press .
2.  To adjust the volume of door camera, you can press Up or Down to choose (9 levels are adjustable), and press Left or Right to adjust.
3.  To set the ring time, you can press Up or Down to choose Ring Time(l-15 seconds are selectable. When two indoor monitors are connected to one door camera, if the time set in two indoor monitors is different, the time is subject to the shorter one), and press Left or Right to adjust.
4.  If setting Ringing Time at Os, door station will not make a sound when the call button is pressed.
5.  If you want to set the unlock time, you can press Up or Down to choose Unlock Time(l-9 seconds are selectable), and press Left or Right to adjust.
6.  Press to save the settings and return to the previous menu.
   Note: When two indoor monitors are connected to one door camera, the settings of these two indoor monitors should be the same.

Chapter 9: Language

1.  Press Up or Down to choose “Language· menu, then press .
2.  Press Up or Down to choose the corresponding language(O stands for English, l stands for Dutch, 2 stands for Polish, 3 stands for German, 4 stands for French, 5 stands for Italian, stands for Portuguese, 7 stands for Spanish, 8 stands for Russian, 9 stands for Turkish).
3.  Press to save the settings and return to the previous menu.

Chapter 10: Wallpaper
You can choose different wallpaper.

Chapter 11: Version
Press Up or Down to choose ·version· menu, then press . You can check the software version in it.

Chapter 12: Video Set

1.  Press Up c, or Down to choose “Video Set.” menu, then press @ to Select .
2.  Press Up c, or Down to choose On or Off to enable or disable the function.
3.  Press to save the settings and return to the previous menu.

With this Auto Video Record On, the camera will record the video of visitor automatically when the visitor presses the Call button on the door camera. You can view this record easily on the indoor monitor.

Notes:

1.  During the conversation/monitoring, the camera can record the video of visitor and save it into the indoor monitor.
2.  The longest time for video recording is 75 seconds.

Chapter 13: Video

1.  Press Up or Down to choose “Video Record.” menu, then press @ to Select. SD card needs to be inserted, otherwise the following interface will appear. When the SD card is inserted, the upper right corner of the interface will appear .

You can view or delete the video record in this menu.

1.  Press Up or Down to choose “View Record” menu.
2.  Press , and press Up or Down to view the records.
3.  To delete the record, use Up or Down to choose it and then press . The display will show” •• Press to confirm.
4. This icon means Delete All. Pressing the system will prompt whether to delete all the records. Press OK to delete and press Return to exit.
5.  After one warning tone, it will display the next view.
6.  Press to return to the previous menu.

Chapter 14: Default set

This function allows you to reset the indoor monitor to the factory default.

1.  Press Up or Down to choose “Default Set.” menu, then press .
2.  Press Up or Down to choose YES or NO to enable or disable the function.
3.  Press to save the settings and return to the previous menu.
   Note: If you reset the indoor monitor, all the settings will return to the factory default.
   Result: After resetting, the indoor monitor will return to standby mode.

ENGINEERING MODE

Register

1. Firstly, insert the small screw driver on position inside the battery compartment of door camera for 3 seconds. It will give an indication tone and the backlight of call button will lighten.
   Secondly, press on the indoor monitor, select the Register menu, press Up or Down to choose one door camera (1-2 are selectable) that you want to connect, and press to confirm the settings. Then the door camera will automatically search for the indoor monitor which needs to be registered. When the indoor monitor gives an indication tone, it means that it is registered successfully .

2.  Pressing and then selecting the Register menu, the system will enter into the following interface. It indicates that the indoor monitor is registered successfully.

3.  If you want to delete the registration, you can press . The screen will show” “, press to confirm. Press to return to the home page.

Notes:

1.  The registration of door camera can be up to 60 seconds.
2.  The registration of indoor monitor can be up to 20 seconds.
3.  The product can support max. 2 door cameras and 2 indoor monitors.

Power Saving Mode

1.  If the door camera is battery-powered, the indoor monitor cannot enable monitoring function with factory default. Press Register button for 3 seconds and make the door camera enter the registration status. Press Register button again for 3 seconds. The door camera will give “bi-bi-bi” tone and switch from power saving mode into power consumption mode. Then the monitoring function is available for the indoor monitor.
2.  In registration status, press Register button for 3 seconds. The door camera will beep and switch from power consumption mode into power saving mode. In this case, the monitoring function is unavailable.

OPERATIONS

Monitor
As for monitoring function, the LCD will automatically display the corresponding menu in accordance with the registered door camera.

1.  In the standby mode, press .
2.  With one door camera registered, the indoor monitor will enter into monitoring mode directly.
3.  With two door cameras registered, the LCD will display Monitor 1# and 2#. You can press Up or Down to choose the one you need to watch, then press .
4.  In monitoring mode, press Accept key to enter into intercom communication.
   Note: Monitoring time can last up to 45 seconds.

Alarm
When someone takes the door camera apart from the bracket, the door camera and indoor monitor will give alarm. The door camera will first call the main indoor monitor. If the main indoor monitor doesn’t respond, the door camera will call the sub indoor monitor. In this case, the call button is invalid on the door camera. Press or on indoor monitor to stop alarm sounds.

Notes:

1.  The alarm time can be up to 5 minutes.
2.  During the alarm, door camera can only connect with one indoor monitor.

Calling indoor monitor
If the visitor presses the Call button on the door camera, the corresponding indoor monitor rings and the image of the visitor appears on the LCD of indoor monitor.

1.  If the resident doesn’t want to answer, press to cancel the call.
2.  After the resident presses , the indoor monitor will stop ringing. Then the conversation starts. Press to end the conversation.
3.  When the door camera calls indoor monitor, if the indoor monitor has no operation ( ), it will return to the main interface. The flashing icon of missed call will show in the upper left corner to remind the user of viewing the images. Pressing the End key in the main interface or viewing picture in the “Snap Show” can cancel the flashing icon.
   Note: Missed call icon will be displayed when Auto Snap is enabled.

Backlight

1.  If the door camera is supplied by DC 12V, the backlight of call button is on.

2.  If the door camera is supplied by battery, the backlight of call button is off.
   Note: During the calling, alarm or monitoring status, if the door camera is powered by battery in power saving mode, the backlight of call button will be off.

3.  In the registration, calling, alarm, monitoring and intercom status, the backlight will flash.

TECHNICAL PARAMETERS

INSTALLATION & USAGE

Since working frequency of this product is 2.4G, the wavelength is short and wireless signal has poor penetration, the device will get disturbed from other products of the same frequency. In order to ensure smooth communication, please note the following.

1.  It’s best to install door camera in a place away from rain and wind. Try to avoid the sunlight into camera lens. Do not place the door camera directly on metal security door, because metal will have barrier effect on the signal. Door camera can be installed on the wall nearby.
2.  Since the product is straight line transmission, try to reduce the obstacle between door camera and indoor monitor. The obstacle will weaken the signal. In the case that there is an obstruction that affects transmission distance, please shorten the distance between transmitter and receiver if possible when meeting usage needs. When the product goes through different obstructions, general signal attenuation situation is as below:
3.  Do not put any product of the same frequency such as router, bluetooth device and microwave oven next to our device in order to avoid causing the interference and shortening of communication distance. If the number of walls between door camera and indoor monitor results in ineffective communication, please adjust the location of two devices to reduce wall number between two devices over a horizontal distance. When door camera is in communication with indoor monitor, if someone walks on the distance between two devices, the communication might be less effective. The indoor monitor cannot be put in a low-lying place or corner.

SAFETY INSTRUCTIONS

In order to protect you and others from harm or protect your device from damage, please read the following information before using the device.
Do not install the device in the following places:

• Do not install the device in high-temperature and moist environment or the area close to magnetic field, such as around electric generator, transformer or magnet.
• Do not place the device near heating products such as electric heater or the fluid container.
• Do not place the device in the sunshine or near the heat source, which might cause discoloration or deformation of the device.
• Do not install the device in an unstable position to avoid the property losses or personal injury caused by the falling of device.

Guard against electric shock, fire and explosion

• Do not use damaged power cord, plug or loose outlet.
• Do not touch the power cord with wet hands or unplug the power cord by pulling.
• Do not bend or damage the power cord.
• Do not touch the device with wet hands.
• Do not make the power supply slip or cause the impact.
• Do not use the power supply without the manufacturer’s approval.
• Do not have the liquids such as water go into the device.

Clean Device Surface

• Clean the device surfaces with soft cloth dipped in some water, and then rub the surface with dry cloth.

Other Tips

• In order to prevent damage to the paint layer or the case, please do not expose the device to chemical products, such as the diluent, gasoline, alcohol, insect-resist agents, opacifying agent and insecticide.
• Do not knock on the device with hard objects.
• Please be careful when standing up from under the device.
• Do not disassemble, repair or modify the device at your own discretion. The arbitrary modification is not covered under warranty. When any repair required, please contact the customer service center.
• If there is abnormal sound, smell or fume in the device, please unplug the power cord immediately and contact the customer service center.
• When the device isn’t used for a long time, the adaptor and memory card can be removed and placed in dry environment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>