milwaukee M18FDD3 M18 FUEL 13mm Drill Driver Instruction Manual

milwaukee M18FDD3 M18 FUEL 13mm Drill Driver

Product Information

• Product Name: M18 FDD3 M18 FPD3

Original Usage Instructions:

• Text Section: Technical Data, important Safety and Working Hints and description of Symbols

Product Usage Instructions

1. Before starting any work on the machine, remove the battery pack.
2. Check the power plug and power cord for any damage before use. Only a specialized technician should repair any faults.
3. When working on the tool, always wear ear protectors as the noise levels can be high.
4. Refer to the drilling capacity specifications for different materials such as wood, brick, and tile.
5. Recommended battery types and charger should be used for optimal performance.

Note: Please refer to the complete user manual for detailed instructions and safety guidelines.

Assembly Instruction

Remove the battery pack before starting any work on the machine

TECHNICAL DATA M18 FDD3 M18 FPD3

• Type: Cordless Drill Driver: Cordless percussion drill/driver
• Production code: 4813 05 01 XXXXXX MJJJJ: 4813 14 01 XXXXXX MJJJJ

• 0-500 min-1
• 0-2100 min-1

| |

• 0-500 min-1
• 0-2100 min-1

Impact range, 1st gear Impact range, 2nd gear| –
–| |

• 0-7800 min-1
• 0-33000 min-1

Torque (5,0 Ah battery)| 158,2 Nm| | 158,2 Nm
Drilling capacity in wood with flat bit| 38 mm| | 38 mm
with auger bit with hole saw with selfeedbit|

• 38 mm
• 89 mm
• 65 mm

| |

• 38 mm
• 89 mm
• 65 mm

Drilling capacity in brick and tile| –| | 15,88 mm
Wood screws (without pre-drilling)| 16 mm| | 16 mm
Drill chuck range| 1,6 – 13 mm| | 1,6 – 13 mm
Weight according EPTA-Procedure 01/2014 (2.0 Ah…. 12.0 Ah)| 1,9…3,1 kg| | 1,9…3,1 kg
Recommended ambient operating temperature| | -18…+50 °C|

• Recommended battery types: M18B…; M18HB
• Recommended charger: M12-18…; M1418C6
• Noise information: Measured values determined according to EN 62841.
• Typically, the A-weighted noise levels of the tool are:
  • Sound pressure level / Uncertainty K: 95,78 dB(A) / 3 dB(A): 95,78 dB(A) / 3 dB(A)
  • Sound power level / Uncertainty K: 106,78 dB(A) / 3 dB(A): 106,78 dB(A) / 3 dB(A)

Always wear ear protectors!

• Vibration information: Total vibration values (vector sum in the three axes) determined according to EN 62841.
• Vibration emission value ah / Uncertainty K
• Impact drilling into concrete: – : 11,3 m/s2 / 1,5m/s2
• Drilling into metal: 1,85 m/s2 / 1,5 m/s2 1,85 m/s2 / 1,5m/s2
• Screwing: 1,48 m/s2 / 1,5m/s2 1,48 m/s2 / 1,5 m/s2

WARNING!

• The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.

• The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly increase the exposure level over the total working period.

• An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
  Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the accessories, keep the hands warm, organization of work patterns.

• WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

• Save all warnings and instructions for future reference.

DRILL SAFETY WARNINGS

Safety instructions for all operations

• Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory or fasteners may contact hidden wiring.
• Cutting accessory or fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
• Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
• Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
• Brace the tool properly before use. This tool produces a high output torque and without properly bracing the tool during operation, loss of control may occur resulting in personal injury.
• Safety instructions when using long drill bits
• Never operate at higher speed than the maximum speed rated of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting the personal injury.
• Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting the personal injury.
• Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal injury.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS

• Use protective equipment. Always wear safety glasses when working with the machine. The use of protective clothing is recommended, such as dust mask, protective gloves, sturdy non-slip footwear, helmet and ear defenders.

• WARNING To reduce the risk of injury in applications that produce a considerable amount of dust, use a Milwaukee dust extraction solution in accordance with the solution’s operating instructions.

• The dust produced when using this tool may be harmful to health. Do not inhale the dust. Wear a suitable dust protection mask.

• Do not machine any materials that present a danger to health (e.g. asbestos).

• Switch the device off immediately if the insertion tool stalls! Do not switch the device on again while the insertion tool is stalled, as doing so could trigger a sudden recoil with a high reactive force. Determine why the insertion tool stalled and rectify this, paying heed to the safety instructions.

• The possible causes may be:

  • it is tilted in the workpiece to be machined
  • it has pierced through the material to be machined
  • the power tool is overloaded

• Do not reach into the machine while it is running.

• The insertion tool may become hot during use.
  WARNING! Danger of burns

  • when changing tools
  • when setting the device down

• Chips and splinters must not be removed while the machine is running.

• When working in walls ceiling, or floor, take care to avoid electric cables and gas or waterpipes.

• Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage.

• Remove the battery pack before starting any work on the machine.

• Do not dispose of used battery packs in the household refuse or by burning them. Milwaukee Distributors off er to retrieve old batteries to protect our environment.

• Do not store the battery pack together with metal objects (short circuit risk).

• Use only System M18 chargers for charging System M18 battery packs. Do not use battery packs from other systems.

• Battery acid may leak from damaged batteries under extreme load or extreme temperatures. In case of contact with battery acid wash it off immediately with soap and water. In case of eye contact rinse thoroughly for at least 10 minutes and immediately seek medical attention.

ALWAYS USE A SIDE HANDLE

• when using a 9.0 Ah or higher capacity battery pack; the output torque of some tools may increase. If your drill/driver did not come with a side handle, use the spare part side handle (see explosion drawing of the tool).
• Do not insert the bit on the tool when the tool is running, and switch is lock on status, the bit will be running and may hurt the user.
• WARNING This device contains a lithium button/coin cell battery. A new or used battery can cause severe internal burns and lead to death in as little as 2 hours if swallowed or enters the body. Always secure the battery cover. If it does not close securely, stop using the device, remove the batteries, and keep it away from children. If you think batteries may have been swallowed or entered the body, seek immediate medical attention.
• Warning! To reduce the risk of fi re, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach containing products, etc., can cause a short circuit.

SPECIFIED CONDITIONS OF USE

• M18FDD3: The battery drill/screwdriver may be used for drilling and screwdriving for independent use away from mains supply.
• M18 FPD3: The electronic battery percussion drill/screwdriver is designed for drilling, percussion drilling, as well as screwdriving for independent use away from mains supply.
• Do not use this product in any other way as stated for normal use.

RESIDUAL RISK
Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise in use and the operator should pay special attention to avoid the following:

• Injury caused by vibration
  Hold the product by designated handles and restrict working time and exposure.

• Exposure to noise can cause hearing injury.
  Wear ear protection and limit exposure.

• Injury due to flying debris
  Wear eye protection, heavy long trousers, gloves and substantial footwear at all times.

• Inhalation of toxic dusts.

NOTES FOR LI-ION BATTERIES

• Use of Li-Ion batteries
• Batteries which have not been used for some time should be recharged before use.
• Temperatures in excess of 50°C (122°F) reduce the performance of the battery. Avoid extended exposure to heat or sunshine (risk of overheating).
• The contacts of chargers and battery packs must be kept clean.
• For an optimum life-time, the batteries have to be fully charged, after used.
• To obtain the longest possible battery life remove the battery pack from the charger once it is fully charged.
• For battery storage longer than 30 days:
• Store the battery where the temperature is below 27°C and away from moisture
• Store the battery in a 30% – 50% charged condition
• Every six months of storage, charge the battery as normal.
• Battery protection for Li-Ion batteries
• In extremely high torque, binding, stalling and short circuit situations that cause high current draw, the tool will vibrate for about 5 seconds, the fuel gauge will flash, and then the tool will turn OFF. To reset, release the trigger.
• Under extreme circumstances, the internal temperature of the battery could become too high. If this happens, the fuel gauge will fl ash and the battery pack cool and then continue work.

Transport of Li-Ion batteries

Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
Transportation of those batteries has to be done in accordance with local, national and international provisions and regulations.

• The user can transport the batteries by road without further requirements.
• Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts.

When transporting batteries:

• Ensure that battery contact terminals are protected and insulated to prevent short circuit.
• Ensure that battery pack is secured against movement within packaging.
• Do not transport batteries that are cracked or leak.
• Check with forwarding company for further advice

AUTOSTOP

• The AUTOSTOP™ kickback feature senses a bind of the drill. The control lamp fl ashes and the electronic switch off the machine. To switch on, release the trigger and press it again.
• The machine is delivered with Autostop activated.
• Switch off Autostop: turn the forward/reverse switch to the middle position and then press the on/off switch 5 times. The indicator light lights up and then slowly goes out (see illustrations in the picture section).
• Switch on Autostop: turn the forward/reverse switch to the middle position and then press the on/off switch 5 times. The control light fl ashes (see illustrations in the picture section).
• The selected Autostop mode remains stored even if the battery is removed.

CLEANING
The ventilation slots of the machine must be kept clear at all times.

MAINTENANCE

• Use only Milwaukee accessories and Milwaukee spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses).
• If needed, an exploded view of the tool can be ordered. Please state the machine type printed as well as the six-digit No. on  the label and order the drawing at your local service agents or directly at: Techtronic Industries GmbH, Max-Edyth-Strafe 10, 71364 Winnenden, Germany.

SYMBOLS

• Please read the instructions carefully before starting the machine.
• CAUTION! WARNING! DANGER!
• Remove the battery pack before starting any work on the machine.
• Always wear goggles when using the machine.
• Wear ear protectors!
• Wear a suitable dust protection mask.
• Wear gloves!
• Accessory – Not included in standard equipment, available as an accessory.
• Do not dispose of waste batteries, waste electrical and electronic equipment as unsorted municipal waste. Waste batteries and waste electrical and electronic equipment must be collected separately.
• Waste batteries, waste accumulators and light sources have to be removed from equipment.
  • Check with your local authority or retailer for recycling advice and collection point.
  • According to local regulations retailers may have an obligation to take back waste batteries and Waste electrical and electronic equipment free of charge. Your contribution to re-use and recycling of waste batteries and waste electrical and electronic equipment helps to reduce the demand of raw materials.
  • Waste batteries, in particular containing lithium and waste Electrical and electronic equipment contain valuable, recyclable materials, which can adversely impact the environment and the human health, if not disposed of in an environmentally compatible manner. Delete personal data from waste equipment, if any.
• n0 No-load-speed
• V Voltage
• Direct Current
• European Conformity Mark
• UK Conformity Mark
• Ukraine Conformity Mark
• Eurasian Conformity Mark

Features

Assembly

• Insulated gripping surface

• Accessory – Not included in standard equipment.
• Connect the machine to a suitable dust extractor.

EC DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product described under “Technical Data” fulfills all the relevant regulations and directives listed below and that the following harmonized standards have been used.

• Copyright 2022
• Techtronic Industries GmbH Max-Eyth-Str. 10
• 71364 Winnenden Germany
• +49 (0) 7195-12-0
• www.milwaukeetool.eu
• Techtronic Industries (UK) Ltd Parkway
• Marlow SL7 1YL
• UK

References

• Il motore di ricerca per risparmiare sui tuoi acquisti | Trovaprezzi.it
• Milwaukee Tool Europe | Cordless Power Tools, Outdoor Tools, Hand Tools, PPE, Work wear. Storage and Accessories. | Milwaukee Tools Europe
• Que Faire de mes Déchets ? Découvrez les solutions pour tous vos déchets et nos conseils pour en produire moins.
• Milwaukee M18 FPD3 | Confronta prezzi | Trovaprezzi.it
• Elettroutensili al miglior prezzo | Trovaprezzi.it

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>