DNAKE 280SD-Series 1-button Door Station User Guide

DNAKE 280SD-Series 1-button Door

PACKAGE CONTENTS

Please make sure the package contains the following items:

MODEL: 280SD-R2

MODEL: 280SD-RS

MODEL: 280SD-Cl2(Flush Mounting)

MODEL: 2805D-Cl2(Surface Mounting)

PICTURES

MODEL: 280SD-R2

MODEL: 280SD-R5

MODEL: 280SD-Cl2

BASIC OPERATION

1. Call indoor monitor
   In standby mode, press the call button on door station to call indoor monitor. During the call, press the call button on door station again to end the call. If the call fails or indoor monitor is busy, door station will emit a beep.

2. Unlocking by card
   Put the registered IC card on card reader area of the door station. If IC card has been authorized, after unlocking the door by card, the system will issue a voice message that “the door has been opened”, otherwise it will emit a beep.

SYSTEM CONFIGURATION

1. RS485
   It can connect to the equipment with RS485 interface.
   RS485 interface can output 12V /lOOmA power. Connection of +12V isn’t require if it is unused.

2. Exit/Door-detector
   Connect with Exit button and door-detector switch; DIN is reserved terminal, please don’t connect it.
   

3. Network
   Connect to management center, indoor monitor or other network device through.

4. Power/Switching value output
   Connect power interface of door station to 12V DC power. Switching value output connects with electric lock. Independent power supply is required for the lock.

5. RS485/Switching Value Output/Exit/Door-detector
   

INSTALLATION

MODEL: 280SD-R2

Installation Instructions
Suggestion], The camera should be 1450~
1550mm above the ground. The camera at this height can capture human face perfectly.

MODEL: 2805D-RS

Installation Instructions:
[Suggestion]: The camera should be 1450~
1550mm above the ground. The camera at this height can capture human face perfectly.

MODEL: 280SD-Cl2(Surface Mounting)

Installation Instructions:
[Suggestion], The camera should be 1450~
1550mm above the ground. The camera at this height can capture human face perfectly.

MODEL: 280SD-Cl2(Flush Mounting}

• Product size: 190x95x27mm
• Flush mounting box size:180X85X45mm
• Trepanning size: 185x90x52mm
  

Installation Instructions:
[Suggestion]: The camera should be 1450~
1550mm above the ground. The camera at this height can capture human face perfectly.

SAFETY INSTRUCTIONS

In order to protect you and others from harm or your device from damage, please read the following information before using the device.
Do not install the device in the following places:

• Do not install the device in high-temperature and moist environment or the area close to magnetic field, such as the electric generator, transformer or magnet.
• Do not place the device near the heating products such as electric heater or the fluid container.
• Do not place the device in the sun or near the heat source, which might cause discoloration or deformation of the device.
• Do not install the device in an unstable position to avoid the property losses or personal injury caused by the falling of device.

Guard against electric shock, fire and explosion:

• Do not use damaged power cord, plug or loose outlet.
• Do not touch the power cord with wet hand or unplug the power cord by pulling.
• Do not bend or damage the power cord.
• Do not touch the device with wet hand.
• Do not make the power supply slip or cause the impact.
• Do not use the power supply without the manufacturer’s approval.
• Do not have the liquids such as water go into the device.

Clean Device Surface

• Clean the device surfaces with soft cloth dipped in some water, and then rub the surface with dry cloth.

Other Tips

• In order to prevent damage to the paint layer or the case, please do not expose the device to chemical P.roducts, such as the diluent, gasoline, alcohol, insect-resist agents, opac1fying agent and insecticide.
• Do not knock on the device with hard objects.
• Do not press the screen surface. Overexertion might cause flopover or damage to the device.
• Please be careful when standing up from the area under the device.
• Do not disassemble, repair or modify the device at your own discretion.
• The arbitrary modification is not covered under warranty. When any repair required, please contact the customer service center.
• If there is abnormal sound, smell or fume in the device, please unplug the power cord immediately and contact the customer service center.
• When the device isn’t used for a long time, the adaptor and memory card can be removed and placed in dry environment.
•  When moving, please hand over the manual to new tenant for proper usage of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>