DNAKE S212 Door Station User Guide

DNAKE S212 Door Station

REMARK

Please follow the user manual for correct installation and testing. If there is any doubt please call our tech-supporting and customer center.
Our company applies ourselves to reformation and innovation of our products. No extra notice for any change. The illustration shown here is only for reference. If there is any difference, please take the actual product as the standard.
The product and batteries must be handled separately from household waste. When the product reaches the end of service life and needs to be discarded, please contact the local administrative department and put it in the designated collection points in order to avoid the damage to the environment and human health caused by any disposal. We encourage recycling and reusing material resources.

PACKAGE CONTENTS

Please make sure the package contains the following items:

MODEL: S212(Surface Mounting)

MODEL: S212(Flush Mounting)

MODEL: S213M(Surface Mounting)

MODEL: S213M(Flush Mounting) MODEL: S213K(Surface Mounting)

MODEL: S213K(Flush Mounting)

Overview

MODEL: S212

Note:
Calling indicator light: The 1st indicator light will be turned on if the calling button is pressed.
Talking indicator light: The 2nd indicator light will be turned on if the call is picked up or Door Station is monitored.
Unlocking indicator light: The 3rd indicator light will be turned on for 3s when the door is opened.
Relay Outputs: Support 2 relay outputs.

MODEL: S213M

Note:
Calling indicator light: The 1st indicator light will be turned on if the calling button is pressed.
Talking indicator light: The 2nd indicator light will be turned on if the call is picked up or Door Station is monitored.
Unlocking indicator light: The 3rd indicator light will be turned on for 3s when the door is opened.
Relay Outputs, Support 2 relay outputs.

MODEL: 5213K

Note:
Calling indicator light: The 1st indicator light will be turned on if the calling button is pressed.
Talking indicator light: The 2nd indicator light will be turned on if the call is picked up or Door Station is monitored.
Unlocking indicator light: The 3rd indicator light will be turned on for 3s when the door is opened.
Relay Outputs: Support 2 relay outputs.

BASIC OPERATION

1. Call indoor monitor
   In standby mode, press the call button on the door station to call the indoor monitor. During the call, press the call button on the door station again to end the call. If the call fails or an indoor monitor is busy, the door station will emit a beep.

2. Unlocking by card
   Put the registered IC/ID card in the card reader area of the door station. If IC/ID card has been authorized, after unlocking the door by card, the system will issue a ringtone and the indicator light is on for 3 seconds, otherwise, it will emit a beep.

SYSTEM CONFIGURATION

SYSTEM DIAGRAM

1. Network
   Standard RJ45 interface connects with master station, indoor monitor or other network equipment by network switch.

2. Power
   Power interface of door station connects with 12V DC power.

3. Exit/Door-detector/Fire Fighting Linkage

4. RS485/Switching Value Output
   Enable to connect equipment with RS485 interface.
   Connect to the lock module(independent power supply is necessary for the lock).

warning

1. When connecting to an inductive load device such as a relay or electromagnetic lock, you are recommended to use a diode lA/ 400V(included in the accessories ) in anti-parallel with the load device to absorb inductive load voltage peaks. Intercom will be better protected in this way.
2. The load current of the relay cannot be greater than 2A.
   See attached picture for more details.

Card Reader Interface

The interface can be connected to one IC/ID card reader or be used for reading the information of built-in card reader.

Note: Door station can only be connected to one card reader or management device at a time.

INSTALLATION

MODEL: S212/S213M/S213K(lnstallation of Wiring Cover)

MODEL: S212(Surface Mounting-86 Mounting Box)

Product dimension: 88xl68x32.Smm
Surface mounting product dimension: 88xl68x34mm

Installation Instructions:
[Suggestion]: The camera should be 1450~
1550mm above the ground. The camera at this height can capture human face perfectly.

MODEL: S212(Surface Mounting-118 Mounting Box)

Product dimension, 88xl68x32.Smm
Surface mounting product dimension: 88xl68x34mm

Installation Instructions:

[Suggestion]: The camera should be 1450~
1550mm above the ground. The camera at this height can capture human face perfectly.

MODEL: S212(Flush Mounting)

Product dimension, 88xl68x32.Smm
Flush mounting product dimension: 120x210x48mm
Hole-cutting dimension: 98xl99x42mm

MODEL: S213M/S213K(Surface Mounting-86 Mounting Box) Product dimension: 88xl88x32.Smm
Surface mounting product dimension: 88xl88x34mm

Installation Instructions:

[Suggestion]: The camera should be 1450~
1550mm above the ground. The camera at this height can capture human face perfectly.

MODEL: S213M/S213K(Surface Mounting-118 Mounting Box)

Product dimension, 88xl88x32.Smm
Surface mounting product dimension: 88xl88x34mm

Installation Instructions:

[Suggestion]: The camera should be 1450~
1550mm above the ground. The camera at this height can capture human face perfectly.

MODEL: S213M/S213K(Flush Mounting) Product dimension: 88xl88x32.5 mm
Flush mounting product dimension: 120x230x48mm
Hole-cutting dimension: 98x219x42mm

Installation Instructions:

[Suggestion]: The camera should be 1450~ 1550mm above the ground. The camera at this height can capture human face perfectly .

SAFETY INSTRUCTIONS

In order to protect you and others from harm or your device from damage, please read the following information before using the device.
Do not install the device in the following places:

• Do not install the device in a high-temperature and moist environment or an area close to a magnetic field, such as the electric generator, transformer or magnet.
• Do not place the device near the heating products such as the electric heater or the fluid container.
• Do not place the device in the sun or near the heat source, which might cause discoloration or deformation of the device.
• Do not install the device in an unstable position to avoid property losses or personal injury caused by the falling of device.

Guard against electric shock, fire and explosion:

• Do not use damaged power cord, plug or loose outlet.
• Do not touch the power cord with wet hand or unplug the power cord by pulling.
• Do not bend or damage the power cord.
• Do not touch the device with wet hand.
• Do not make the power supply slip or cause the impact.
• Do not use the power supply without the manufacturer’s approval.
• Do not have the liquids such as water go into the device.

Clean Device Surface

• Clean the device surfaces with soft cloth dipped in some water, and then rub the surface with dry cloth.

Other Tips

• In order to prevent damage to the paint layer or the case, please do not expose the device to chemical P.roducts, such as the diluent, gasoline, alcohol, insect-resist agents, opacifying agent, and insecticide.
• Do not knock on the device with hard objects.
• Do not press the screen surface. Overexertion might cause flop over or damage to the device.
• Please be careful when standing up from the area under the device.
• Do not disassemble, repair or modify the device at your own discretion.
• The arbitrary modification is not covered under warranty. When any repair is required, please contact the customer service center.
• If there is an abnormal sound, smell or fume in the device, please unplug the power cord immediately and contact the customer service center.
• When the device isn’t used for a long time, the adaptor and memory card can be removed and placed in dry environment.
• When moving, please hand over the manual to new tenant for proper usage of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>