HIKVISION Wireless Conference Speakerphone User Manual
- June 4, 2024
- Hikvision
Table of Contents
HIKVISION Wireless Conference Speakerphone
Packing List
Functions
| Press the button to adjust the speaker volume by level.
Press and hold the button to adjust the speaker volume continuously.
---|---
| Press to answer/hang up a call.
Long preess the button to reject a call.
| Press to turn on/off pickup function. White light: Speakerphone picking up
sounds. Red light: Speakerphone off. When the speakerphone is picking up
sounds, hold the button for 5 s, the white light will flash twice, and the
steady and transient smart noise reduction will be turned on. Hold the button
for another 5 s, the funtion will be turned off.
It is recommended to turn off the steady and transient smart noise reduction when the speakerphone is picking up sounds from a long distance.
| Hold the button to turn on/off the device.|
---|---|---
While not charging| Solid Red:
Power≤15%.
| While charging| Flashing White:
The device is charging.
|
Solid Yellow:
15%<power≤30%
|
Solid White:
The device is fully charged.
|
Solid White:
Power>30%|
If the device has not been connected via any means of of Bluetooth, wireless
dongle or wireless cable within 10 minutes and no other operations are
performed, the device will automatically shut down.|
| Hold the button to switch Bluetooth state.|
Solid White| Only previously paired devices can connect to Bluetooth.|
Flashing Blue| Unpaired devices can be paired with Bluetooth.|
Solid Blue| The speakerphone connects to Bluetooth successfully.|
Light Off| Bluetooth is off.|
If the Bluetooth has not been connected within 3 minutes, the device
automatically turns off Bluetooth pairing. To connect again, you need to
manually turn on Bluetooth.|
Connection
-
Bluetooth Connection
The default Bluetooth name is 8-mic Speakerphone for Bluetooth connection. -
Wireless Dongle Connection
The default wireless receiver name is Multi-mic Speakerphone for wireless dongle connection. -
USB Cable Connection
- Connect the device to intelligent terminals, such as computers and conference flat panels.
- It is recommended to plug into USB3.0 interface of the terminal.
- It is recommended to connect the the device to intelligent terminals with Type C interface or Type-C-to-A interface.
- It is recommended to use original cable for audio quality.
- The default device name is 8-mic Speakerphone for USB cable connection.
Charging
Setup Guide
Plug the microphone in the computer and run the
conference/video software to use the device.
What should I do if the device cannot work in the conference/video software:
Check if the microphone and speaker of the software is set as its own name in
the audio settings; Check if the computer or the conference panel set the
audio input and ouput as its own name.
The actual product name previals.
FAQ
Visit http://enpinfodata.hikvision.com/analysisQR/showQR/304d56e7 for frequently asked questions.
Safety Instruction
Warnings
Laws and Regulations
The device should be used in compliance with local laws, electrical safety
regulations, and fire prevention regulations.
Electrical Safety
The socket-outlet shall be installed near the equipment and shall be easily
accessible.
Battery
CAUTION: Risk of explosion if the battery is replaced by an incorrect
type.
Improper replacement of the battery with an incorrect type may defeat a
safeguard (for example, in the case of some lithium battery types).
Do not dispose of the battery into fire or a hot oven, or mechanically crush
or cut the battery, which may result in an explosion.
Do not leave the battery in an extremely high temperature surrounding
environment, which may result in an explosion or the leakage of flammable
liquid or gas.
Do not subject the battery to extremely low air pressure, which may result in
an explosion or the leakage of flammable liquid or gas.
Dispose of used batteries according to the instructions.
Cautions
Fire Prevention
No naked flame sources, such as lighted candles, should be placed on the
equipment.
Transportation
Keep the device in original or similar packaging while transporting it.
DO NOT drop the product or subject it to physical shock.
Power Supply
EUT will be charged by specified source which the output circuit comply with
LPS/PS 2.
Refer to the device label for the standard power supply. Please make sure your
power supply matches with your device.
Use a power adapter provided by qualified manufacturers. It is recommended to
provide an independent power adapter for each device as adapter overload may
cause over-heating or a fire hazard.
Maintenance
If the product does not work properly, please contact your dealer or the
nearest service center. We shall not assume any responsibility for problems
caused by unauthorized repair or maintenance.
Cleaning
Please use a soft and dry cloth to clean the interior and exterior surfaces.
Do not use alkaline detergents.
Using Environment
To avoid heat accumulation, good ventilation is required for a proper
operating environment.
DO NOT expose the device to extremely hot, cold, dusty, corrosive, saline-
alkali, or damp environments. For temperature and humidity requirements, see
device specification.
DO NOT expose the device to high electromagnetic radiation.
Emergency
If smoke, odor, or noise arises from the device, immediately turn off the
power, unplug the power cable, and contact the service center.
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and – if applicable – the supplied accessories too are marked
with “CE” and comply therefore with the applicable harmonized European
standards listed under Directive 2014/53/EU(RED), the Low Voltage Directive
2014/35/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points.
For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with
this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb),
or mercury (Hg). For proper recycling, return the battery to your supplier or
to a designated collection point. For more information, see:
www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
For Speakerphone:
This equipment complies with FCC/IC RSS-102 radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
About this Manual
The Manual includes instructions for using and managing the Product. Pictures,
charts, images and all other information hereinafter are for description and
explanation only. The information contained in the Manual is subject to
change, without notice, due to firmware updates or other reasons. Please find
the latest version of this Manual at the Hikvision website
(https://www.hikvision.com/).
Please use this Manual with the guidance and assistance of professionals
trained in supporting the Product.
Trademarks and other Hikvision’s trademarks and logos are the properties
of Hikvision in various jurisdictions.
Other trademarks and logos mentioned are the properties of their respective
owners.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT
DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND
“WITH ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY,
OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR
OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA,
CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF
CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN
CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY
RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK,
HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER,
HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU
ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE
LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT
DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT
LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA
PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY
PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF
MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL
WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR
UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE
LATTER PREVAILS.
Open Source Software Disclaimer
This product cannot be launched without the contribution of open source
software. HIKVISION respects the Intellectual Property of others, has
established and will continue to improve its open source compliance system.
You can get this product’s Open Source Software Declaration and Copyleft
Source Code by visiting http://opensource.hikvision.com/Home.
References
- enpinfodata.hikvision.com/analysisQR/showQR/304d56e7
- Hikvision Open Source Release Center
- HOME
- Hikvision USA - Leading the future of AIoT
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>