FAFREES F26 Pro, F28 Pro Smart EV/Moped User Manual

FAFREES F26 Pro, F28 Pro Smart EV/Moped

Smart EV/Moped

User Manual

• (Model: F26 PRO / F28 PRO)
  Congratulations on your purchase! Please write down your frame number in the blank space below in case of future need.

Contents

• Precautions
• Battery and charging
• Riding
• Disclaimer
• Maintenance and care
• Product function illustration (Model: F26PRO)
• Product installation

Precautions
Before using the product, read the instructions carefully and understand the performance of the product. Do not lend it to someone who cannot manipulate the product for riding. Before riding the bicycle, check whether the brakes are working. Pay attention to the brake tightness. If the brake is too loose, use an Allen key to tighten it. Pay attention to increasing the braking distance when riding in rain or snow. The applicable age range is 16 to 65 years old.

One-handed riding is prohibited!

Disclaimer
Use the product at your own risk. The manufacturer is not responsible for any accidents or injuries that may occur during use.

Maintenance and Care
Regularly maintain and clean the product according to the instructions provided in the user manual. Ensure that all components are in proper working condition.

Product Function Illustration (Model: F26PRO)

Product Installation

1. The state of the bicycle after being taken out of the carton is as shown in the figure above. First, cut all the nylon straps to ensure that the front wheel can be smoothly separated from the frame when the rear wheel can rotate freely.
2. Turn the bicycle upside down as shown above to facilitate the installation of the front wheels.
3. Loosen the fixing screws of the front fork protection rod with an adjustable wrench, and remove the front fork protection rod.
4. Place the front wheel on the front fork for installation, pay attention to the disc brake pad and the disc brake to match in place.
5. Open the accessory small carton, take out the front axle quick release inside, loosen the nut and separate it from the screw.
6. Insert the front axle quick release screw into the front axle core, tighten it with the nut, and then press the quick release handle to lock the front fork.
7. After the front wheel is installed, remove all the protective foams, and then place the bicycle as shown above.
8. Loosen the 4 screws of the handlebar stem, place the handlebar and adjust the horizontal angle of the handlebar, and then fix it with the pipe clamp screws.
9. Tighten each fixing screw with a hexagonal key to fix the handlebar stem to ensure that there is no looseness of the handlebar.
10. Loosen the headlight fixing screw on the front fork, fix the front mudboard fixing hook and the headlight bracket together with the screw on the front fork, and then use the screw to fix the front mudboard support on the front fork, as shown in the right picture above.
11. Place the wheel reflector on the spoke, press the clip into the hole, and use a tool to rotate the clip to lock.

Model: F26 PRO

Model: F28 PRO

PRECAUTIONS

Battery and charging:
Charge at 0℃～45℃, discharge at -20℃～60℃, keep the battery dry, do not put the battery in acidic or alkaline liquid, avoid rain, keep away from fire, heat and high temperature environment. It is strictly forbidden to connect the positive and negative poles of the battery reversely, and it is strictly forbidden to damage, insert the battery or short-circuit the battery. Please use the original special charger when charging, do not exceed 6 hours, and the charging current does not exceed 2A. When not in use for a long time, please store the battery in a cool and dry place, and charge the battery for five hours a month. The user must follow the instructions for use when charging, otherwise the consequences will be borne by the user. Pay attention to the battery type and applicable voltage that the charger can charge, and it is strictly forbidden to mix them. When charging, it should be placed in a ventilated environment, and it is strictly prohibited to charge in a confined space or in a hot sun or high temperature environment. When charging, first connect the battery and the charger, and then the power supply; when the battery is fully charged, first cut off the power supply, and then unplug the charger connector. When the green light is on, the power supply should be cut off in time. It is forbidden to connect the charger to the power supply for a long time without charging. During the charging process, if the indicator light is abnormal, a peculiar smell appears, or the charger casing is overheated, stop charging immediately and repair or replace the charger. During the use and storage of the charger, pay attention to avoid the entry of foreign objects, especially avoid the inflow of water or other liquids, so as not to cause a short circuit inside the charger. Try not to carry the charger with the bicycle. If you really need to carry it, you should place it in the toolbox after the shock absorption treatment is done. Do not disassemble or replace the accessories in the charger by yourself.

Riding:
Do not use it until you read the instructions carefully and understand the performance of the product; do not lend it to someone who can’t manipulate the product for riding. Before riding the bicycle, check whether the brakes are working. Pay attention to the brake tightness. If the brake is too loose, use an Allen key to tighten it. Pay attention to increasing the braking distance when riding in rain or snow. Applicable age: 16 to 65 years old.

Please be sure to wear a safety helmet when riding a bicycle, follow the traffic rules, and do not drive on motorized lanes and roads with many pedestrians. Please check the tire pressure before riding, the
recommended tire pressure is 40～65PSI.
Downhill and non-paved roads do not exceed 15KM/h.
When using the motor, please be careful not to hit it vigorously and keep the rotating shaft lubricated.
Riding beyond the maximum load is not allowed (the maximum load is 120KG)
After use, the car can not be parked in the building hall, evacuation stairs, safety exits, and must be parked correctly in accordance with the safety rules.
One-handed riding is prohibited!

Disclaimer:
After riding, please store the bike in a place without sunlight and rain, not in residential buildings; always check the motor and brake; check the screws and the places that need to be fastened regularly, and tighten them regularly. Recommended torque: (unit: kgf.cm) handlebar screw 60-80, handle screw 175-200, seat cushion screw 175-200, wheel screw 320-450;
The front and rear wheels of the vehicle should be located in the center of the front fork or frame;
Always check the tire for scratches, cracks or excessive wear. The inner tube and the valve should be perpendicular to the wheel hub. Damaged or excessively worn tires need to be replaced immediately. Please find a professional technician to replace your tire. If your tire accidentally punctures and leaks, please contact a professional technician for repair or replacement.

Maintenance and care:
For the product model, specifications or related information mentioned in this User Manual, the company reserves the right of modification and final interpretation; the functions of the specific model mentioned in this User Manual are only applicable to that specific model;
The product models, specifications, or related information mentioned in the User Manual may be changed without notice; without prior written permission of the company, the User Manual may not be copied, modified, reproduced, transmitted, or published in any form. Please read the Manual carefully before using the product, and operate in accordance with the Manual, otherwise the company will not be liable for product damage or personal or property damage caused by improper use or error.

Product function illustration (Model:F26PRO)

1. Shift Lever
2. Central Display
3. Brake Lever
4. Stem
5. Headlight
6. Front fender
7. Tire
8. Rim
9. Brake Disc
10. Front wheel quick release
11. Front Fork
12. Disc brake
13. Chain cover
14. Chainwheel
15. Pedal
16. Chain
17. Rear Derailleur
18. Motor
19. Tail light
20. Rear carrier
21. Seat Tube Adjustment Quick Release
22. Seat Tube
23. Saddle
24. Battery Lock Key Hole
25. Lithium Battery
26. Power light switch button
27. Battery charging hole

Product installation

1. The state of the bicycle after being taken out of the carton is as shown in the figure above. First, cut all the nylon straps to ensure that the front wheel can be smoothly separated from the framewhen the rear wheel  can rotate freely.

2. Turn the bicycle upside down as shown above to facilitate the installation of the front wheels.

3. Loosen the fixing screws of the front fork protection rod with an adjustable wrench, and remove the front fork protection rod.

4. Place the front wheel on the front fork for installation, pay attention to the disc brake pad and the disc brake to match in place.

5. Open the accessory small carton, take out the front axle quick release inside, loosen the nut and separate it from the screw.

6. Insert the front axle quick release screw into the front axle core, tighten it with the nut, and then press the quick release handle to lock the front fork.

7. After the front wheel is installed, remove all the protective foams, and then place the bicycle as shown above.

8. Loosen the 4 screws of the handlebar stem, place the handlebar and adjust the horizontal angle of the handlebar, and then fix it with the pipe clamp screws.

9. Tighten each fixing screw with a hexagonal key to fix the handlebar stem to ensure that there is no looseness of the handlebar.

10. Loosen the headlight fixing screw on the front fork, fix the front mudboard fixing hook and the headlight bracket together with the screw on the front fork, and then use the screw to fix the front mudboard support on the front fork, as shown in the right picture above.

11. Place the wheel reflector on the spoke, press the clip into the hole, and use a tool to rotate the clip to lock.

12. Accessories list, as shown above.

13. When installing the pedals, pay attention to the port of the pedal shaft. The pedal with “L” stamp is the left pedal, the stamp with “R” is the right pedal, and the right pedal is installed on the side of the sprocket.
    Note: The left pedal is tightened to the left, and the right pedal is tightened to the right.

14. Install the tail light : first connect the control wire of the tail light to the tail light, and then fix the tail light to the rear hanger with screws.

Display installation

1. The display can be installed only after the handlebar is installed. For the convenience of installation, as shown in the left picture above, one of the pipe clamps of the instrument can be completely removed first.
2. Gently open the fixing pipe clamp of the instrument first, in order to install it firmly, first place the pipe clamp gasket on the handlebar tube, and then clamp the pipe clamp into the handlebar tube, as shown in the middle picture above.
3. Tighten the screws behind the pipe clamps of the display to fix it, as shown in the right picture below.
4. Loosen the fixing clip of the button unit, click it into the handlebar tube, and then tighten the fixing screw, as shown in the figure below.
5. Connect the cable of the display, as shown in the figure above; pay attention to the arrow marks of the two connectors.

The state of the display after installation is as shown in the figure above.

The state of the bicycle after the installation is completed, as shown in the figure above.

Removing the battery: Insert the key, twist it to the right with your right hand, and pull the battery out with your left hand.
After the battery is removed, it can be charged alone with the charger.

Function introduction:

1. Charging: Refer to item 27 of Figure 2, the charging hole can be seen on the right side of the battery in the frame, and it can be charged by connecting the charger. When the battery is full and the charger indicator turns from red to yellow-green, it means it is fully charged.
2. Turn on/off: refer to Figure 4 and press and hold the ” ” button to turn on/off the power of the display.
3. Display: The display screen lights up after power on, displaying information such as power, speed, motor speed, mileage, etc. The power speed is initially 0. Press the “+” and “-” buttons to increase and decrease the power speed of electric drive mode.
4. Front light: Refer to Figure 4, long press the “+” button to turn on/off the front light.
5. Power-assisted mode: power-assisted riding, step on the pedals of the bicycle, and automatically start electric power after a certain speed. If you don’t need assistance, you can turn off the power of the display.
6. Speed transmission: Refer to Figures 4 and 5, when the bicycle is running, you can change the mechanical speed by flipping the shift levers.
7. Electric mode: Refer to Figure 5, press the thumb throttle, and the bicycle can accelerate forward. The greater the pressing range, the faster the bicycle will run. For safety reason, please press the thumb throttle lightly and accelerate slowly.

Product parameter

Note: The parameters in brackets belong to F28 PRO.

Remarks: Electricity, load, tire pressure, road environment, chain and wheel axle lubrication, etc. will affect the maximum speed; the range refers to the data obtained from continuous testing from fully charged to completely exhausted with a riding speed of 15-25km/h and a load of 60kg on a flat hardened road; driving habits, temperature, load, tire pressure, road environment and other factors will affect the range.

Display user instructions

Important information about safe use:

1. Before plugging or unplugging the display, please make sure to cut off the power supply of Ebike first. Plugging or unplugging with power will cause permanent electrical damage to the display;
2. When installing the display on the handlebar, do not over tighten the hexagon socket screws. Normally, 0.2N.m of torque can securely install the instrument on the handlebar. Excessive tightening will cause damage to the instrument structure.
3. Do not immerse the display in water or use water spray to clean the meter. When cleaning, please use a soft cloth dampened with water to wipe. Do not use any cleaning agents to wipe.
4. The USB charging port on the display cannot provide waterproof protection when in use. When riding in the rain, please make sure that the protective rubber of the USB port is closed tightly. It is forbidden to use the display to connect external devices in the rain.
5. Do not dispose of the display or any other Ebike accessories as residential garbage. Please abide by local laws and regulations, and dispose of or recycle Ebike accessories in an environmentally friendly manner.
6. The damage or failure of the display caused by improper installation or use is not covered by the after-sales warranty.

Parts description and specifications

Parts description

DTK3 Buttons

Dimensions

Reliability

Conformities

Installation

Install the display unit

1. Use two M3*12 hexagon socket screws 1-1 and 1-2 to lock the left and right fixing brackets to the handlebars. Tightening torque: 0.2N.m. Do not over-tighten ,otherwise it will cause damage to the display.
2. After adjusting the display to a proper angle, use two M3*6 hexagon socket screws 2-1 and 2-2 to tighten it.
3. If you want to install it on a 22.2mm or 25.4mm handlebar, please use the attached adapter rubber ring.

Install the button unit

1. Use one M3 hexagon socket screw 3 to lock the control unit on the left handlebar, the recommended position: the right side of the brake fixing ring.

2. Tightening torque: 0.2N.m. Do not over-tighten, otherwise it will cause damage to the instrument.

3. Align the arrow marks on the outlet connector of the meter and the Ebike outlet connector, and insert the two cables firmly

System operation

Initial operation
Turn on the power to the riding interface

1.  Long press the “Power” button and the interface is fully lit to enter the riding interface.
2. Press “+” or “-” button to change the power speed. The default is 0, and the range is 0-5 speed.
3. Short press the “Power” key to switch the “Multi-function display area”.

DTK3 button functions

1. “+” Button
2. “-” Button
3. Power Button

Note: Long press the “+” and “-” buttons at the same time to enter or exit the menu interface; long press the “+” and “power” buttons to clear the Trip information.

Meter interface

Menu interface
In the meter interface, long press the “+” and “-” buttons to enter or exit the menu interface. To ensure user safety, the menu interface can only be entered when the Ebike is stationary (speed is 0); when the speed is not 0, even in the menu setting, it will force to exit the menu and return to the riding interface. In the menu interface, press the “Power” button to jump and confirm the menu items, and the “+” and “-” buttons to set the menu items.

Set wheel diameter
When selecting the “Size” item, press the “Power” button to enter this item, and then press “+” or “-” button to select the wheel diameter, ranging from 04-99, in particular, 27.5 inches displays “27.5”; then press the “Power” button to confirm And exit the item.

Set speed unit
When selecting the “Unit” menu item, press the “Power” button to confirm KM/H or MPH.

Set speed limit
Select the “Speed” menu item and set the speed limit range from 0.0-99.9 km/h. The final speed limit is determined by the motor. The default is 25 km/h.

Set automatic shutdown time
When selecting the “OFF” menu item, press the “power” button to enter this item, the press “+” or “-” button to confirm the time, the range is 0-10 min, where 0 means to cancel the automatic shutdown; then press the “power” button again to confirm and exit the item.

Set automatic shutdown time
When selecting the “OFF” menu item, press the “power” button to enter this item, the press “+” or “-” button to confirm the time, the range is 0-10 min, where 0 means to cancel the automatic shutdown; then press the “power” button again to confirm and exit the item.

Reset
Select the “Reset” menu item, select “Yes” or “No” with the “+” and “-” buttons, and press the “Power” key to confirm and proceed to the next setting. “No” is displayed by default. Restoring factory settings can restore the default factory parameters, including speed unit, wheel diameter, speed limit, automatic shutdown time and brightness.

Error code interface
When there is an error, the error indicator will be on and the real-time speed area will be displayed as the error code.

KM5S protocol error code:

COPYRIGHT © FAFREES. ALL RIGHTS REVERSED.
Visit www.fafreesebike.com or contact support@fafreesebike.com
for more information and after-sale service.

MANUFACTURER INFORMATION
Manufacturer: Guangzhou Gedesheng Electric Bike Co.,Ltd. Address: No.105, Commercial Street, Guangtang Village, Xinya Street, Huadu District, Guangzhou, Guangdong, China

References

• kgf.cm
• Fafrees Ebike

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>