speco technologies VLB5 2MP HD TV1 IR Bullet Camera User Manual

speco technologies VLB5 2MP HD TV1 IR Bullet Camera

Product Information

The VLB5/VLB6/VLD5/VLD6M/VLT7 camera series is the latest technology in surveillance systems. It features high definition and sensitivity, low noise and distortion, and supports HD video transmission using a common coaxial cable. The camera series is designed to meet the requirements of HD monitoring in traditional surveillance systems.

Warnings
Speco Technologies reserves the right to modify product design and specifications without notice.

Installation
Before installation, ensure that the wall or ceiling is strong enough to withstand three times the weight of the camera.
Install and use the camera in a dry environment.
For VLB5/VLB6 cameras, follow the steps below:

1. Drill screw holes and cable hole on the wall according to the provided drill template.
2. Route and connect the cables.
3. Secure the mounting base with the camera to the wall using screws.
4. Adjust the bracket for optimal view angle.
5. Perform focus and zoom adjustment if necessary.

For Dome Cameras (VLD5/VLD6M), follow the steps below:

1. Attach the drill template to the desired location on the wall and drill screw holes and cable hole accordingly.
2. Rotate the trim ring anticlockwise to remove it from the camera.
3. Loosen the screws to open the lower dome and route/connect the cables.
4. Secure the camera to the wall using screws provided.
5. Perform three-axis adjustment for optimal angle.
6. Install the lower dome back and fix it with screws. Then put the trim ring onto the lower dome and rotate it clockwise until locked. Remove the protection film.

For VLT7 cameras, loosen the set screw to disassemble the camera.

Backlight Compensation (BLC)
When the back of the captured object is too bright, you can set BLC for the captured object to make it clearer.

Video Output
The camera supports four video output modes: AHD, TVI, CVI, and
CVBS. To switch between video outputs:

1. Remove the cover of the video switch cable.
2. Hold and press the button in the video switch cable for 5 seconds to switch the current video output.

Cables
The camera requires the following cables:

• Video Output Cable
• Power Cable

Please refer to the user manual for more detailed information and instructions.
Thank you for purchasing our product. Speco Technologies is constantly developing and improving products. We reserve the right to modify product design and specifications without notice and without incurring any obligation.

Warnings

• If the product does not work properly, please contact the dealer or where the product was purchased. Speco Technologies is not responsible for any problems caused by improper operation or repair.
• Do not expose the unit to heavy stress, violent vibration or long-term exposure to water and humidity during transportation, storage, and/or installation.
• Do not install near sources of heat.
• Only install the product in environments inside the specification operating temperature and humidity range.
• Do not install the camera near power lines, radar equipment or other electromagnetic radiation.
• Do not block any ventilation openings if any.
• Use all the weatherproofing hardware requirements to minimize weather intrusion.

Introduction

This camera series is the latest technology and advanced circuit design, which features high definition and sensitivity, low noise and distortion and supports HD video transmission with the common coaxial cable, ensuring the requirement of the HD monitoring in the traditional surveillance system.

• High Resolution
  Adopt high-performance sensors, providing high definition and clear image.

• High Transmission Performance
  Real-time transmission with high speed and long distance.

• DNR
  Reduce noise from the brightness and color signal.

• OSD
  Access the camera settings which can be clearly displayed through the main menu.

• White Balance
  Adjust the color temperature according to the environment automatically.

• ICR Auto Switch
  The filter will filter infrared light during the daytime and change to normal at night to ensure a high sensitivity and clear image.

• AGC
  Adjust the gain of an amplifier, enabling the camera to output the standard video signal in different lighting condition.

• Wide Dynamic Range (WDR)
  When there are both very bright and very dark areas simultaneously in the field of view, this function will balance the brightness level and provide clear images.

• Backlight Compensation (BLC)
  When the back of the captured object is too much bright, you can set BLC for the captured object to make it clearer.

Cables

Video Switch: Four video output modes can be optional–AHD, TVI, CVI and CVBS (a) remove the cover of the video switch cable; (b) hold and press the button in the video switch cable for 5 seconds to switch the current video output.

Installation

• Before you start, please make sure that the wall or ceiling is strong enough to withstand three times the weight of the camera. Please install and use the camera in the dry environment.
• You’d better install back the lens cover or lower dome less than 4 hours after removing it.
• The mounting types of cameras are only for reference.

Mounting for VLB5/VLB6

1. Drill the screw holes and the cable hole on the wall according to the drill template.
2. Route and connect the cables .
3. Secure the mounting base with camera to the wall with screws as shown below.
4. Bracket adjustment. Before adjustment, preview the image of the camera on a monitor and then loosen the fixed ring to adjust the view angle of the camera. Tighten the fixed ring after the adjustment.
5. Focus and zoom adjustment ( If the camera you get is fixed lens, please skip this step). Open the cover of the camera then adjust the focus and zoom screws to get a clear image. Finally, install the cover back to the camera.

Mounting for Dome Camera

Mounting for VLD5/VLD6M

1. Attach the drill template to the place where you want to fix the camera and then drill the screw holes and the cable hole on the wall according to the drill template.
2. Rotate the trim ring anticlockwise to remove it from the camera.
3. Loosen the screws to open the lower dome. Then route and connect the cables.
4. Secure the camera to the wall with screws provided as shown below.
5. Three-axis adjustment. Before adjustment, preview the image of the camera on a monitor and then adjust the camera according to the figure below to get an optimum angle.
6. Install the lower dome back to the camera and fix it with screws. Then put the trim ring onto the lower dome and then rotate it clockwise until it is locked. Finally, remove the protection film softly.

Mounting for VLT7

1. Loosen the set screw to disassemble the camera.
2. Attach the drill template to the place where you want to fix the camerarill the screw holes and the cable hole on the wall according to and then d the drill template.
3. Route and connect the cables. Then secure the mounting base to the ceiling or wall with the screws provided.
4. Install the camera unit and enclosure to the mounting base and then adjust the dome to obtain an optimum view angle.
5. Finally, secure the camera with the set screw.

Specifications

Models

Specifications

| VLB5| VLB6| VLD5| VLD6M| VLT7
---|---|---|---|---|---
Camera
Image Sensor| 1/2.9″ CMOS
Resolution| 2MP
Image size| 1920×1080
Video Output| AHD/TVI/CVI/CVBS (*camera comes defaulted to HD-TVI)
Image System| PAL/NTSC
Electronic Shutter| Auto;  1/50s~1/100000s(PAL);1/60s~1/100000s  (NTSC)
IR Distance (feet)| 65.6~98.4| 98.4~164.0| 32.8~65.6| 65.6~98.4| 65.6~98.4
Frame Rate| 30fps(60Hz),25fps(50Hz)
Min. Illumination| Color:0.001lux@F1.2, AGC ON; B/W: 0lux with IR
Lens| 2.8mm| 2.8~12mm (varifocal)| 2.8mm| 2.8~12mm (motorized)| 2.8mm
Lens Mount| M12| D14| M12| D14| M12
S/N Ratio| ≥ 52dB(AGC OFF)
Ingress Protection| IP67| IP67| IP67&IK10| IP67&IK10| IP67
Functions
Function Control| OSD (UTC control)
Day &Night| ICR
WDR| Yes (digital WDR)| 120dB
Digital NR| Yes
AGC| Yes
Auto White Balance| Yes
Front Light Compensation| Yes
Defog| No
HLC| No| No| Yes| Yes| Yes
Sharpness| No
Mirror| Yes
Smart IR| Yes
Image Setting| Yes
Defect Correction| Auto
Others
Power Supply| DC12V (± 10%)| DC12V (± 15%)
Power Consumption| IR OFF: < 1W; IR ON : < 3.5W
Working Environment| -4 °F ~ 122 °F, 10 % ~ 90 %(relative humidity)
Dimensions (inch)| 6.6×2.9×2.9| 8.6×3.2×3.2| Ф4.7 × 3.5| Ф5.6 × 3.9| Ф3.7×3.3

Model : VLB5 /VLB6/VLD5/VLD6M/VLT7

Federal Communications Commission (FCC) Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

FCC Responsible Party:
Speco Technologies
200 New Highway
Amityville, NY 11701
www.specotech.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>