Lumens AI-BOX1 Automates Multi Camera Voice Tracking User Manual

• CamConnect is divided into 8 equal parts according to Senheisser’s horizontal angle of view. They correspond to CamConnect Azimuth Angle 1 to 8.

• If the forbidden area is enabled on the Sennheiser Control Cockpit software, the corresponding position of CamConnect will also be affected. Example: If the forbidden area is set to 0° to 60°, the audio signal from 0° to 45° of CamConnect Array Azimuth 1 and 45° to 60° of Array Azimuth 2 will be ignored.

Nureva

•  HDL300 Audio Conferencing System
• HDL310 Audio Conferencing System
• HDL410 Audio Conferencing System

Yamaha
Yamaha RM-CG Ceiling Array Microphone

Operation Interface Description

Microphone Setting

5

| ****

Port

| Display based on the connected devices

§ Shure：2202

§ Sennheiser：45

§ Nureva：8931

< Remark> Only Nureva allows customized input of PORT

6| Connect| Enable/Disable microphone connection

7

| ****

Setting Mode

| Enable/Disable Setting mode

When the Setting mode is enabled, the microphone can receive signals, but it will not trigger the camera to the preset position.

Enabling this mode is recommended when setting the preset position, to prevent microphone from interference from other sounds, triggered to unintended positions.

---|---|---

8

| Audio Trigger Level >

dB

| Triggered only if audio source exceeds the preset dB

< Remark>For Sennheiser/Nureva only

9

| ****

Time To Trigger Preset

| Audio Reception Delay Settings

When a second sound trigger occurs, there will be a delay in calling the preset position based on the configured duration in seconds.

10

| ****

Back To Home Time

| Back To Home Time Settings

If there is no audio input at the venue, it will trigger, after the set seconds, and return to Home

11| Back to Home Camera| Back To Home Camera Setting
12| Back To Home Position| Home Position Setting
13| Apply| Setting completed; click Apply

Camera Control & Status

output settings)

2

| ****

Refresh/ Add

| Click to search for the device again or manually enter the specified IP, and click [Add] to add it

※ Please ensure that the camera and AI-BOX1 are on the same network segment.

3

| ****

Connect/ Disconnect

| Click [Connect] to establish a connection with the camera or /

[Disconnect] to cancel the connection

The connected camera will be highlighted in blue

§ Disconnected:

4| PTZ Control| Click to enable PTZ control

Refer to 3.2.1 PTZ Control for function description

5

| ****

AI Setting

| Enable/Disable AI People Tracking

§ Center Stage: After triggering to the preset position, the tracked person will be positioned in the center of view and tracking will stop after 5 seconds

§ Continuous Tracking: The system will continuously track a person and keep them positioned in the center

1. **PTZ Control

No| Item| Function Descriptions
---|---|---
1| Preview window| Display the screen currently captured by the camera
2| L/R Direction| L/R Direction / Normal
3**| Mirror / Flip| Set image mirroring/ flip

4

| ****

Pan/Tilt/Home

| Adjust the Pan/Tilt position of the camera screen

Click [Home] button to return to its central position

5

| ****

Preset setting

| Click the number keys directly to call the preset

Ÿ Save preset: Click first and then a number key

Ÿ Clear preset: Click first and then a number key

6| AF/MF| Switch to Auto/Manual Focus. Focus can be adjusted in Manual
7| Zoom| Zoom In/ Zoom Out ratio
8| Exit| Exit the PTZ Control page

Microphone orientation and camera preset relationship setting
After the microphone device is connected, the camera can be controlled to turn to the corresponding preset position according to the microphone detection position.

1

| ****

Indicator

| This indicator shows the status of microphone signal reception. (A green light indicates successful reception)

2

| ****

Array No. Azimuth Angle

| § Array No.: For Shure models:

§ Azimuth Angle: Applicable to Sennheiser, Nureva, and Yamaha models. The angle can be manually adjusted

3| Camera| Select the desired camera from the dropdown menu
4| Preset No.| Select the preset position for the camera from the dropdown menu

System Setting

2

| ****

Auto Connection

| Auto connection settings

§ Sound Device: Microphone

 |  | § Camera: Camera

§ Video Output: Automatic image output

---|---|---
3| Auto Save| Set automatic save interval in seconds
4| Reset/ Apply| Reset/Apply your settings

5

| ****

Network

|

Ethernet Setting. When it is set to Static IP, the setting can be modified. Once the settings are completed, click Apply.

Video Output Setting

2

| ****

Video Output Layout

| Configure the layout of the video output according to the provided reference in section 3.5.1 Video Output Layout

§ Cross: 4-split screen

§ PBP: Picture by Picture screen

§ Crop: Screen cropping function

< Remark> Choose either Cross/PBP only

3

| ****

Seamless Switching

| Enable/disable the microphone connection function

The system is set up for single screen output, and the screen switching is triggered by the microphone signal.

1. **Video Output Layout

**
If there are three connected cameras, they will be displayed in a 4-grid layout, with one grid showing a black screen.

Start Video Output
Click to output the camera images to HDMI or UVC devices
< Note> Choose only either HDMI/UVC output. For setting the Output Mode, please refer to 3.5 Video Output

Information

Web Page Function

Device Setting

Network

Video Output Setting

3

| ****

Video Switching Mode

| Enable/disable the microphone connection function

The system is set up for single screen output, and the screen switching is triggered by the microphone signal.

4

| ****

Video Output Layout

| Configure the layout of the video output according to the provided reference in section 3.5.1 Video Output Layout

§ Cross: 4-split screen

§ PBP: Picture by Picture screen

§ Crop: Screen cropping function

< Remark> Choose either Cross/PBP only

Maintenance

About

Connect to a conference video software

1. Set the output mode of AI-BOX1 to UVC and click the start streaming option

2. Launch a video software like Skype, Zoom, Microsoft Teams, or other similar software

3. Choose the video source, to output camera images
   Video Source Name: Lumens CamConnect Processor

Troubleshooting

This chapter describes problems you may encounter while using AI-BOX1. If you have questions, please refer to related chapters and follow all the suggested solutions. If the problem still occurred, please contact your distributor or the service center.

1.

|

Unable to search camera devices

| 1.  Check the power supply of camera or PoE power supply is stable.

2.  Make sure the PC is connected to the camera with the USB cable

3.  Replace the cables and make sure they are not faulty

2.| No response from the microphone

detection position

| Please confirm that the microphone device is in Connect status

3.

|

When using with a Sennhesier microphone, no response at the specific angle

| 1. Make sure the Azimuth Angle settings in the CamConnect software include that angle position

2. Make sure if the angle is set as the forbidden area on Sennhesier

Control Cockpit software. Refer to _3.2 Sennhesier Microphone System _for details.

4.

| When setting camera preset positions, if the microphone detects signals from other directions, it may cause the camera to move to other positions,

thus interrupting the setting

|

Please refer to _3.1 Microphone Setting _to enable the Setting mode Once enabled, the microphone can receive signals, but it will not trigger the camera to the preset position

5.

|

Used together with Shure TCC2 microphone. Sound detection not sensitive, not accurate

| Suitable for large-area positioning when Shure Designer Automatic coverage is On.

If more accurate positioning is required, it’s suggested to disable Automatic coverage, adjust Gain value/Position manually, reduce beamforming angle, to achieve more accurate positioning

Copyright Information

• Copyrights © Lumens Digital Optics Inc. All rights reserved.
• Lumens is a trademark that is currently being registered by Lumens Digital Optics Inc.
• Copying, reproducing or transmitting this file is not allowed if a license is not provided by Lumens Digital Optics Inc. unless copying this file is for the purpose of backup after purchasing this product.
• In order to keep improving the product, the information in this file is subject to change without prior notice.
• To fully explain or describe how this product should be used, this manual may refer to names of other products or companies without any intention of infringement.
• Disclaimer of warranties: Lumens Digital Optics Inc. is neither responsible for any possible technological, editorial errors or omissions, nor responsible for any incidental or related damages arising from providing this file, using, or operating this product.

References

• Download | Lumens

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>