CookPerfect ApS CP-W-200 Wireless Meat Thermometer with Wi-Fi User Manual
- June 9, 2024
- CookPerfect
Table of Contents
Quick Start Guide
ApS CP-W-200 Wireless Meat Thermometer with Wi-Fi
Charge the Wireless Sensor for minimum 8 hours before use.
To Turn ON the device remove the Wireless Sensor from Docking station
Launch the CookPerfect App and select connection type. CookPerfect Wireless
supports both Bluetooth and Wi-Fi.
Using Wi-Fi – ONLY 2.4GHz Network is supported!
Charging:
Wi-Fi and Bluetooth LEDs are off when sensor is charging. Sensor can be placed
in both sides of the Docking station for charging.
If Wi-Fi LED is flashing while sensor is placed in the Docking station, make
sure that the metal ring and needle have proper contact to the magnets. The
Docking station is rechargeable, use the USB cable to recharge battery.
During use:
The sensor must always be inserted into the meat pass the Safety mark.
After use:
Make sure that the metal ring (point A) and needle (point B) are clean before
charging.
LED status Indicator:
Wi-Fi LED is flashing when the Docking station is on. Bluetooth LED is solid
Blue when connection to sensor is established. Wi-Fi LED is solid Green when
connection to local network is established.
Green USB-C LED: Docking station is charging. Red USB-C LED: Docking station
is low on battery.
Note:
To reset place sensor in the Docking station until all lights are OFF.
Safety Instructons:
The appliance is not to be used by children or persons with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction.Children should be supervised
and instructed not to play with the appliance. Use CookPerfect Wireless only
for intended use. CookPerfect Wireless is designed for cooking of meat.
To avoid damage always place the Sensor past the safety mark on the needle,
when inserted into the meat. After use the Sensor can be very Hot – use
protection gloves to remove needle. Don’t submerge the Sensor in cold water
after cooking. Sensor is ONLY water resistant and NOT waterproof – only clean
by hand wash.
Always make sure that the Sensor is dry before charging. DO NOT submerse
Docking station and Sensor in water or liquids. DO NOT put the Docking station
and Sensor in a microwave. Max. internal temperature of the Sensor is 100°C
(212°F). Max. ambient temperature of the Sensor is 300°C (662°F). Temperatures
above limits may damage the Sensor. The Docking station ´s max. temperature is
60°C (140°F) Store CookPerfect Wireless in a dry place.
Operation is subject to the following two conditions:
( 1 )this device must not cause interference, and
( 2 )this device must accept any interference, including interference that may
cause undesired operation of the device.
EC Declaration of Conformity:
CookPerfect ApS hereby confirm that following accessory comply with all
permanent and essential requirements as per the EU directive 1999/5/EC.
Model name: CookPerfect Wireless Single.
Brand name: CookPerfect.
Product type: Intelligent meat thermometer.
Applied standards according to corresponding EU directive:
EN301489-1, EN301489-17, EN62479, EN62368, EN300328, IEC62321
FCC Requirement
changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>