speco technologies O8VD3M 8 Megapixel Network IR Outdoor Dome Camera User Guide

speco technologies O8VD3M 8 Megapixel Network IR Outdoor Dome Camera

Product Information

The O8VD3M network camera is a high-quality surveillance camera designed to provide clear and reliable video footage. It comes with various features and components to ensure easy installation and optimal performance.

Important Safeguards and Warnings

1. Electrical Safety: The camera should be installed and operated in accordance with local electrical safety codes. Use a certified/listed 12VDC Class 2 power supply or a suitable PoE switch. Ensure proper grounding to reduce the risk of electric shock.
2. Operation and Daily Maintenance: Before performing any maintenance work, shut down the camera and unplug the power cable. Avoid touching the CMOS sensor optic component. Use a blower to clean dust from the lens surface, and always use a dry soft cloth to clean the device. In case of excessive dust, use a cloth for cleaning.

Warning
This camera should only be installed and examined by qualified personnel. Any unauthorized changes or modifications may void the warranty.

Statement
This guide is for reference purposes only. Product specifications, manuals, and components are subject to modification without prior notice. Speco Technologies reserves the right to modify these without incurring any obligation. Speco Technologies is not liable for any loss caused by improper operation.

Package Contents

• Camera
• Quick start guide
• CD
• Screwdriver
• Rubber plug
• Drill template
• CVBS&DC IN cables
• 8 Plastic screw anchors
• 4 Rubber o-rings for screws
• Junction box

Camera Overview
The camera features the following components and interfaces:

1. Ethernet Connector
2. Audio Input (MIC)
3. Audio Output (HP)
4. CVBS Video Output
5. Alarm Input/Output
6. Power Connector
7. Zoom
8. Zoom+
9. Micro SD Card Slot
10. Reset
11. DC IN & CVBS Interface
12. Microphone

Connecting Network Cable

1. Loosen the nut from the main element.
2. Run the network cable (without RJ45 connector) through both elements.
3. Crimp the cable with an RJ45 connector.
4. Connect the cable to the waterproof connector.
5. Tighten the nut and the main cover.

Installation
Before starting the installation process, ensure that the wall or ceiling can withstand three times the weight of the camera.

1. Attach the drill template of the junction box to the desired installation location.
2. Drill the screw hole and cable hole on the wall according to the drill template.
3. Install the junction box onto the wall using the provided screws.
4. Align the gap of the trim ring with the microphone by turning the trim ring with your fingers.
5. Remove the trim ring from the gap of the camera.

Welcome
Thank you for purchasing this network camera!
This owner’s manual is designed to be a reference tool for your system. Please read this manual carefully before operating the unit and retain it for future reference. Should you require any technical assistance, contact Speco Technologies Tech Support at 1-800-645-5516

Important Safeguards and Warning

1. Electrical safety
   • All installation and operation here should conform to local electrical safety codes. Use a certified/listed 12VDC Class 2 power supply or adequate PoE switch.
   • Please note: The product must be grounded to reduce the risk of electric shock. Improper handling and/or installation could run the risk of fire or electrical shock.
2. Environment
   • Do not expose the unit to heavy stress, violent vibration or long-term exposure to water and humidity during transportation, storage, and/or installation.
   • Do not install near sources of heat.
   • Only install the product in environments inside the specification operating temperature and humidity range.
   • Do not install the camera near power lines, radar equipment or other electromagnetic radiation.
   • Do not block any ventilation openings if any.
   • Use all the weatherproofing hardware requirement to minimize weather intrusion.
3. Operation and Daily Maintenance
   • Please shut down the device and then unplug the power cable before you begin any maintenance work.
   • Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on the lens surface.
   • Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth dampened with a small quantity of neutral detergent. Finally use the dry cloth to clean the device.
   • Please use a professional optical cleaning method to clean the enclosure. Improper enclosure cleaning (such as using cloth) may result in poor IR functionality and/or IR reflection. The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera.
   • Dome cover is an optical device, please don’t touch or wipe cover surface directly during installation and use, please refer to the following methods if dirt is found:
   • Stained with dirt: Use oil-free soft brush or hair dryer to remove it gently.
   • Stained with grease or fingerprint: Use oil-free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens center outward. Change the cloth and wipe several times if it is not clean enough.

Warning

• This camera should be installed by qualified personnel only.
• All the examination and repair work should be done by qualified personnel.
• Any unauthorized changes or modifications could void the warranty.

Statement

• This guide is for reference only.
• Product, manuals and specifications may be modified without prior notice. Speco Technologies reserves the right to modify these without notice and without incurring any obligation.
• Speco Technologies is not liable for any loss caused by improper operation.

Note:
Before installation, check the package and make sure that all components are included. Contact your rep or Speco customer service department immediately if something is broken or missing in the package.

Package

Overview

1. Ethernet Connector
2. Audio Input (MIC)
3. Audio Output (HP)
4. CVBS Video Output
5. Alarm Input/Output
6. Power Connector
7. Zoom-
8. Zoom+
9. Micro SD Card Slot
10. Reset
11. DC IN & CVBS Interface
12. Microphone

It is recommended to install the water-proof connector for outdoor installations.

Connecting Network Cable

1. Loosen the nut from the main element.
2. Run the network cable (without RJ 45 connector) through both elements. Then crimp the cable with RJ 45 connector.
3. Connect the cable to the water-proof connector. Then tighten the nut and the main cover.

Installation

Before you start, please make sure that the wall or ceiling is strong enough to withstand three times the weight of the camera.

1. Attach the drill template of the junction box to the place where you want to install the junction box and then rill the screw hole and calbe hole on the wall according to the drill template.
2. Install junction box onto the wall by using the screws provided.
3. Align the gap of the trim ring with the microphone by turning the trim ring with fingers. Then remove the trim ring from the gap of the camera.
4. Connect the cables, mount the rubber plug to the gap of the mounting base and install the camera onto the junction box.
5. Three-axis adjustment. Before adjustment, preview the image of the camera on a monitor and then adjust the camera according to the figure below to get an optimum angle.

• Install the lower dome back to the camera and fasten it with screws.
• Put the trim ring onto the lower dome. Finally, remove the protection film softly.

Web Operation and Login

IP Scanner can search for the device on the local network.

Operation

1. Make sure that the camera and the PC are connected to the same local network. The camera is set to DHCP by default.
2. Install IP Scanner from the CD and run it after installation. Or download from https://www.specotech.com/ip-scanner/.
3. In the device list, you can view the IP address, model number, and MAC address of each device. Select the applicable device and double click to open up the web viewer. You can also manually enter the IP address in the address bar of the web browser.

The login interface is shown above. Default user name is admin and password is 1234. After logging in, follow directions to install applicable plugins if prompted.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>