SecuFirst CAM214 Outdoor Camera P/T User Guide

SecuFirst CAM214 Outdoor Camera P/T User Guide

info@alcelectronics.eu
www.secufirst.eu
www.alcelectronics.eu

1. Box Content

2.

3.

4.

info@secufirst.eu

5.

6.

7.

8. Android

iOS

9.

10.

11.

12.

13.

14.

15.

16.

1. Box Content

1x IP Camera Pan Tilt for indoor or outdoor use
1x Antenna
1x Adaptor 5V DC / 1.5A
1x RJ45 Internet cable connector
1x Screwpack with screw driver
2x Window Security Stickers
1x Quick Start Guide

2. Product Overview

2.1 Lens
2.2 Light Sensor
2.3 Microphone
2.4 Speaker
2.5 Bracket
2.6 Antenna
2.7 Reset button (Hold for 5 seconds)
2.8 Micro SD Card Slot
3. Connections IP Camera
3.1 Connector Adapter
3.2 RJ45 Connect Jack
The CAM214 is suitable for Wi-Fi or Lan cable internet. If you want to use Lan cable internet then firstly install the camera on Wi-Fi by following the steps in this Quick Start Guide. When the camera is fully installed via Wi-Fi, then you can change the internet to wired by following the below steps.
Note, firstly install the camera with Wi-Fi, after that you can change the internet to Lan cable.

1. Remove the camera adapter from the power socket.
2. Connect the Lan cable to the camera AND modem / router.
3. Insert the camera adapter back into the power socket.
4. Wait for 1 minute, the camera is restarting itself.
5. Your connected via the app.
   If you follow the above steps, then your camera in now working via Lan cable.

4. Preparation before installation on your smart device.

To install this camera you need to prepair the following information:

*4.1 Your own Wi-Fi name, and your own Wi-Fi password.**

The camera must be registered on your own Wi-Fi network during this installation.
Please note, it is our help desk number 1 problem that customers enter their own Wi-Fi network password incorrectly during this installation. The result is that the camera cannot connect and will not display an image. Check your Wi-Fi password carefully (on the back of the router / own documentation).

*4.2 Think of a new security password and document it carefully.**

Security password: Provides access to live video images from your Wi-Fi camera.
During the installation with the app you will be asked to change this password.
Make up this passwords in advance to move faster through the installation.
The new password need to contain:
A) At least 12 characters.
B) At least one capital letter (Example: A)
C) At least one lowercase letter (Example: a).
D) At least one digit (Example: 1).
E) At least one reading sign (Example:!)

*4.3 During the installation, keep your phone or tablet close to the camera (max. 1 meter)**

5. Connect the power adaptor to the IP camera and a 230V socket.
DO NOT connect a Lan cable during installation.

6. Set the camera into the installation mode. Use a paperclip to go inside the reset hole. You will feel a button inside. Press and hold the button for 5 seconds while the power adaptor is connected to the camera and socket.
You will hear a voice to confirm the camera will be set into default mode.
Wait for 1 minute, a voice will be heared again. You can proceed to the next step.

7. Download the app “SecuFirst HD Professional Edition” from the Google Play Store (Android) or Apple Store (iOS)

8. For Android smart devices:

Open the app “Secu First HD Professional Edition” and tab “Press to add new system”.
The app will request you to turn on and off some connections, depending on the current settings of your phone.

• Location: On (Only needed during the installation for better searching performance of the wifi networks).
• Wi-Fi: On
• Mobile data: Off
  Note, make sure you turn OFF your bluetooth. The app must ask you to turn it on during the steps below.
  Tab “Smart Setup”
  Tab “Confirm” if the LED below the camera lens is flashing.
  Tab “Allow” to enable bluetooth on your smart device.
  The app will show the founded camera. Tab on the “HD-0…..”number to select.

For iOS smart devices:
Open the app “SecuFirst HD Professional Edition” and tab “Smart Setup”.
The app will request you to turn on and off some connections, depending on the current settings of your phone.

• Location: On (Only needed during the installation for better seaching preformance of the wifi networks).
• Wi-Fi: On
• Mobile data: Off
  Note, make sure you turn OFF your bluetooth. The app must ask you to turn it on during the steps below.
  Tab “New Device”
  Tab “Confirm” if the LED below the camera lens is flashing.
  The app will show the founded camera. Tab on the “HD-0…..”number to select.

9. Connect the camera to your own Wifi newtwork.

9.1 The app will show you the Wi-Fi networks which the camera can see. Select your own Wi-Fi network (2.4Ghz)

9.2 Insert your own Wi-Fi password.
Please note, it is our help desk number 1 problem that customers enter their own Wi-Fi network password incorrectly during this installation. The result is that the camera cannot connect and will not display an image. We advice you to tab the box “Show password” to
avoid any typing mistakes.
If you did insert a wrong Wi-Fi password, please remove the camera from your app and start from point 6 in this Quick Start Guide.

10. Adjust the Security password.

During this installation the default password of the camera is 123456. We don’t think this is save enough and forse to change this password during the installation (4.2). The new password need to contain:

A) At least 12 characters.
B) At least one capital letter (Example: A)
C) At least one lowercase letter (Example: a).
D) At least one digit (Example: 1).
E) At least one reading sign (Example:!).

10.1 Fill in a new security password. Below the password it must show 3 green bars, then the password meets up to our demands. Tab the eye on the right side of the password to also see the filled in password. This avoids typing mistakes.
Re-confirm the password in the second line.
Tab “Done” on your keyboard and press “Save” in the app.
Do not forget to turn on your mobile data.

11.1 The camera will restart in 30 seconds.
11.2 The camera will try to connect with your own wifi network and password which you have filled in (9.1 and 9.2) The camera will show in green”Connected”. Press Play ( ) to go to the live image of the camera.
12. In the Live view of the camera you see these options:

A) Make a snapshot of the image you have on your phone.
B) Audio unmute / mute
C) Record the live video manually
D) Pre set options to store view points of the camera.
E) Alarm. Press the button to turn on the sirine in the camera. Press again to turn off the sirene.
F) Press and hold the microphone button to speak via the app to the speaker of the camera. Release the button if you would like to hear what is being said nearby the camera (Push to talk function).
G) You can turn on or off the recordings of the camera. This is a privacy mode.
Armed : The camera will record when it see motion.
Disarmed : The camera will not record when there is motion.
Move your finger over the live view image. The camera will turn into each position you prefer. When you have selected the right camera position, you can store this point by leaving the live view (Step 12 H).
H) Leave the live view. Note, always leave the live view when you want to close the app.

13. Settings in the main menu.

A) Add a new device. Only needed when you buy another SecuFirst branded item like:
IP camera, Door Entry, Alarm, Home automation and Lighting.
B) Edit settings. When you tab on this button then 3 buttons will appear in the screenshot. Go to point 14 and 15 of this manual for futher explaination.
C) Reconnect button. If the camera doesn’t show “Connected”,
D) Quad view. If you have more SecuFirst cameras, then it’s possible to have live view in 1 screen of 4 cameras. In the SecuFirst app you can add maximum 99 cameras.
E) Info button.

14. How to insert a micro SD card, type of micro SD is card UHS1, maximum size is 128GB, Class10.

A) Remove the adaptor from the power.
B) Insert the micro sd card in the camera.
C) Insert the adaptor in the power socket.
D) Wait 1 minute for the camera to start up.
E) Go to the advanced settings / sd card settings, to format the micro sd card 1x. How to go to the advanced settings will be explained in the next step

15. Advanced Settings

• Tab “Edit Setting”
• Tab “Setting” above in the app.
• Tab “Advanced” Below in the app.
• The app will ask you to fill in the password which you made in step 10 of this Quick start guide, then press “OK”. If you select “Auto Login” then next time you login, there is no need to re-enter the password.
  Tab “OK”.
  In the big manual all the advanced settings options are explained.
  You can download it from www.secufirst.eu

16. Playback recordings

• Tab “Edit Setting”
• Tab “Event” above in the app.
• A filter will show which looks default 1 hour back on the micro sd card. If you want to look back futher, kindly enlarge the filter by for example adjust the start date.
• Tab “OK”.
• You will get an overview of recordings. These can be playback with 2 different ways.
• Tab “Date / time” of the recording. The video will stream to your phone, leaving nothing behind.
• Tab “Download” to copy the recording from your Micro sd card to your phone.
  When the download has been completed, the download button will change to a share button. Tab the share button to directly share your video with Whats app, E-mail, etc.

17. Installation 2nd Smart device.

• Download and install the “Secufirst HD Professional Edition” app on your smart device.
  Open the app and tap “Press to add new system”.
  Tap “Excisting System”. Enter camera name (Your own choice), DID code and password.
  Tab “Save” Button, then “Yes” to save the system.

18. Downloads available on our website www.secufirst.eu

• Big manual
• How to install movies

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>