SOUNDPEATS Wings2 Wireless Earbuds User Guide

June 12, 2024
SoundPEATS

SOUNDPEATS Wings2 Wireless Earbuds

SOUNDPEATS-Wings2-Wireless-Earbuds \(6\)

First Time of Use

Please open the lid of the charging case to take out the headphones, remove the insulating film from the top of both headphones, then put both headphones back into the charging case.

  1. Open the charging case cover, and take out the headphones, the headphones will automatically turn on and enter the mutual pairing state. When the white and red light in the right earphone flashes alternately, and the white light in the left earphone is always on, the two earphones are successfully paired.
  2. Turn on your device’s Bluetooth and select SOUNDPEATS Wings2 from the Bluetooth list to complete the pairing.

Reset

  1. Clear the pairing record from your device.
  2. Place back both earbuds into charging case and make sure they are in charging status.
  3. Press and hold both buttons for 10s until both LEDs flash in red and white twice, reset complete.

Wearing methods

  1. Identify the left and right earphones.
  2. Adjust the earphones to fit your ears.

Product Diagram

SOUNDPEATS-Wings2-Wireless-Earbuds \(4\)

Control

SOUNDPEATS-Wings2-Wireless-Earbuds

Q&A\

Q1: What does the indicator light of the charging case display?

  • The battery life of the charging case when the earphones are placed back: Sufficient Battery of the charging case – The red light stays on for 4S and then goes out. Low Battery of the charging case – The red light flashes for 4s then goes out.
  • Charging status of the charging case is being charged – the blue light flashes on. the charging case is fully charged – the blue light stays on.

Q2: How to charge the charging case?

  • Connect the charging case to a Type-C charger. (The current does not exceed lA).
  • If the earphones stay idle for an extended period, charge them at least every three months to prevent the battery from being damaged.

Q3: Why are the earphones still connected to the phone when they are put back into the charging case and the case lid is closed?

  • Check whether the charging case has battery power. If it has run out of battery, closing it will not disconnect the earphones from the device.
  • Ensure the earphones are properly placed in the charging case and the charging metal sheet and PIN are clean. And wiping clean the contact points on the earphones and the charging case should fix this issue.

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. this device must accept any interference received, including interference that may cause undesired operation

Changes or modifcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

IC ID

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

  1. this device may not cause interference, and
  2. this device must accept any interference, including interference thatmay cause undesired operation of the device”

RF warning statement:

The device has been evaluated to meet general R exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals