hp L48452-B25 AC Charger User Manual

AC Charger
User Manual

L48452-B25 AC Charger

Regulatory Notices
This document provides country- and region-specific non-wireless and wireless regulatory notices and compliance information for your product. Some of these notices may not apply to your product

Federal Communications Commission notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and sed in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try  o correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio or television technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

For questions regarding this product, write to HP Inc.
1501 Page Mill Road
Palo Alto, CA 94304
email techregshelp@hp.com, or call HP at 650-857-1501.
To identify your product, refer to the part, series, or model number located on the product.

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by HP may void the user’s authority to operate the equipment.
Cables
To maintain compliance with FCC Rules and Regulations, connections to this device must be made with shielded cables having metallic RFI/EMI connector hoods.
Products with wireless LAN devices or HP Mobile Broadband Modules
This device must not be co-located or operating in conjunction with any other antenna or transmitter.
  WARNING: Exposure to Radio Frequency Radiation The radiated output power of this device is below the FCC/Industry Canada radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal operation. During normal operation of devices with displays equal to or less than 30.5 cm (12 inches): To avoid the possibility of exceeding the FCC/Industry Canada radio frequency exposure limits, human proximity to the antennas should not be less than 2.5 cm (1 inch). To identify the location of the wireless antennas, refer to the user guides included with your device. During normal operation of devices with displays greater than 30.5 cm (12 inches): To avoid the possibility of exceeding the FCC/Industry Canada radio frequency exposure limits, human proximity to the antennas should not be less than 20 cm (8 inches), including when the device display is closed. To identify the location of the wireless antennas, refer to the user guides included with your device
CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15- to 5.25-GHz frequency range. FCC/Industry Canada requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25- to 5.35-GHz and 5.65- to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device. The antennas for this device are not replaceable. Any attempt at user access will damage your device.

Canada notices
This Class B digital apparatus meets all requirements of the Canadian Interference- Causing Equipment Regulations CAN ICES-3(B)/NMB-3(B). If this device has WLAN or Bluetooth® capability, the device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Radiation Exposure Statement
This product complies with the US/Canada portable RF exposure limit set forth for uncontrolled environments and is safe for intended operation as described in this manual.  further RF exposure reduction can be achieved if the product can be kept as far as possible from the user’s body or set the device to lower output power if such function is available.
Declaration of Conformity
Products bearing the CE marking and UK marking comply with one or more of the following EU Directives and the applicable UK Statutory Instruments as may be applicable:
RED 2014/53/EU; Low Voltage Directive 2014/35/EU; EMC Directive 2014/30/EU; Ecodesign Directive 2009/125/EC; RoHS Directive 2011/65/EU. Compliance with these directives is assessed using applicable European Harmonised Standards.
Radiofrequency bands and maximum power levels (select products only

Note: Use only HP-supported software drivers and correct country settings to ensure compliance.
The point of contact for EU regulatory matters is HP Deutschland GmbH, HQ-TRE, 71025, Boeblingen, Germany.
The point of contact for UK regulatory matters is HP Inc UK Ltd, Regulatory Enquiries, Earley West, 300 Thames Valley Park Drive, Reading, RG6 1PT, UK.
IMPORTANT: IEEE 802.11x wireless LAN with 5150–5350 MHz and/or 5945–6425* MHz frequency band is restricted for indoor use only in all countries reflected in the matrix. Using this WLAN application(s) outdoors might lead to interference issues with existing radio services.

• Selected products only may use 5925–6425 MHz for UK setup.

AT| BE| BG| CY| CZ
DE| DK| EE| EL| ES
Fl| FR| HR| HU| IE
IT| LT| LU| LV| MT
NL| PL| PT| RO| SE
SI| SK| IS| LI| NO
CH| TR| UK(NI)|

HP Inc.
Адрес: 1501 Page Mill Road, Palo Alto, California 94304, U.S.

Singapore wireless notice
Turn off any WWAN devices while you are onboard the aircraft. The use of these devices onboard aircraft is illegal, may be dangerous to the operation of the aircraft, and may disrupt the cellular network.
Failure to observe this instruction may lead to suspension or denial of cellular services to the offender, or legal action, or both.
Users are reminded to restrict the use of radio equipment in fuel depots, chemical plants, and where blasting operations are in progress. As with other mobile radio transmitting equipment, users are advised that for satisfactory operation of the equipment and for the safety of personnel, no part of the human body should be allowed to come too close to the antennas during operation of the equipment. This device has been designed to comply with applicable requirements for exposure to radio waves, based on scientific guidelines that include margins intended to assure the safety of all people, regardless of health and age. These radio wave exposure guidelines employ a unit of measurement known as the specific absorption rate (SAR). Tests for SAR are conducted using standardized methods, with the phone transmitting at its highest certified power level in all used frequency bands. The SAR data information is based on CENELEC’s standards EN50360 and EN50361, which use the limit of 2 watts per kilogram, averaging over 10 grams of tissue.

Thailand WWAN wireless notice
This telecommunication equipment conforms to the requirements of NBTC.

Laser compliance
Some products may contain a laser that is classified as a Class 1 Laser Product in accordance with US FDA regulations and the IEC 60825-1. Each laser product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 or Laser Notice No. 56, dated May 8, 2019; and with IEC 60825-1:2007.
WARNING! Use of controls or adjustments or performance of procedures other than those specified herein or in the laser product’s installation guide may result in hazardous radiation exposure. To reduce the risk of exposure to hazardous radiation:

• Do not try to open the module enclosure. There are no user-serviceable components inside.
• Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein.
• Allow only HP Authorized service technicians to repair the unit.

Power cord notice
If you were not provided with a power cord for the computer or for an external power accessory intended for use with the computer, you should purchase a power cord that is approved for use in your country or region.
The power cord must be rated for the product and for the voltage and current marked on the product’s electrical rating label. The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product.
In addition, the diameter of the wire must be a minimum of 0.75 mm2/18AWG, and the length of the cord must be between 1.0 m (3.2 ft) and 2 m (6.56 ft). If you have questions about the type of power cord to use, contact your authorized service provider. A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits from the product.

Safety Notices

WARNING! Do not allow the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The AC adapter compiles with the user-accessible surface temperature limits defined by applicable safety standards.
WARNING! To reduce the risk of electric shock or damage to the equipment:

• Plug the AC adapter into an AC outlet that is easily accessible at all times.
• If the power cord has a 3-pin attachment head, plug the cord into a grounded (earthed) 3-pin outlet.

Headset and earphone volume level notice
To prevent possible hearing damage, do not use high volume levels for long periods. Before using a headset or earphones, always reset the volume to a low level.
For your own safety, use headsets or earphones compliant with the headphone limits in EN 50332-2.
When the HP product includes a headset or earphones, the combination is in compliance to EN 50332-1.

Environmental notices

Disposal of waste equipment by users
This symbol means do not dispose of your product with your other household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment. For more information, please contact your household waste disposal service or go to http://www.hp.com/recycle.

Battery Section **

**

When a battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for computer battery disposal.
HP encourages customers to recycle used electronic hardware, HP original print cartridges packaging, and rechargeable batteries. For more information about recycling programs, refer to the HP website at http://www.hp.com/recycle.
For information about removing a user-replaceable battery, refer to the user guide included with the product.
WARNING! Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
WARNING! To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not short external contacts; do not dispose of in fire or water.
WARNING! Keep the battery away from children.
WARNING! To reduce potential safety issues, only the battery provided with the computer, a replacement battery provided by HP, or a compatible battery purchased as an accessory from HP should be used with the computer.
WARNING! A battery subjected to extremely high temperatures in the surrounding environment or extremely low air pressure may result in an explosion or leakage of flammable liquid or gas.

Electronic hardware and battery recycling
HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, see the  P website at http://www.hp.com/recycle.``

Taiwan Declaration of the Presence Condition of the Restricted Substances Marking
#1 Group of products: Accessories that have lens function
Camera, digital video camera, automotive video camera

Restricted substances and their chemical symbols

Unit| (Pb)| (Hg)| (Cd)| (Cr+6)| (PBB)| (PBDE)
Circuit board| | O| O| O| O| O
Shell| O| O| O| O| O| O
Metal part| | O| O| O| O| O
Lens| O| O| | O| O| O
Input/output device| | O| O| O| O| O
Light-sensing component| | O| O| O| O| O
Cable| | O| O| O| O| O

Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition.
Note 2: “O” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
Note 3: “—” indicates that the restricted substance corresponds to the exemption.

#2 Group of products: Accessories that have speaker function
Speakers

Restricted substances and their chemical symbols

Unit| (Pb)| (Hg)| (Cd)| (Cr+6)| (PBB)| (PBDE)
Circuit board| | O| O| O| O| O
Shell| O| O| O| O| O| O
Metal part| | O| O| O| O| O
Speaker| | O| O| O| O| O
Cable| | O| O| O| O| O

Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicates that the percentage content of the restricted substance exceeds the reference percentage value of present condition.
Note 2: “©” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
Note 3: “—” indicates that the restricted substance corresponds to the exemption.

#3 Group of products: Accessories that have read/write function
CD/DVD/Floppy device, storage device (external HDD/SSD, USB flash drive), docking device, card reader, writing device (stylus, pen), one-to-multiple hub, touch mat, magnetic stripe reader, barcode scanner, fingerprint reader, port replicator/ USB hub

Restricted substances and their chemical symbols

Unit| (Pb)| (Hg)| (Cd)| (Cr+6)| (PBB)| (PBDE)
Circuit board| | O| O| O| O| O
Shell| O| O| O| O| O| O
Metal part| | O| O| O| O| O
Read/write component| _| O| O| O| O| O

Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition.
Note 2: “O” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
Note 3: “—” indicates that the restricted substance corresponds to the exemption.

#4 Group of products: Accessories that have PCB as main part
Memory card, network card, graphic card, and other internal add-on cards

Restricted substances and their chemical symbols

Unit| (Pb)| (Hg)| (Cd)| (Cr+6)| (PBB)| (PBDE)
Circuit board| | O| O| O| O| O
Active component
(transistors and integrated
circuits)| O| O| O| O| O| O
Passive component
(resistors and capacitors)| | O| O| O| O| O
Solder| _| O| O| O| O| O

Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition.
Note 2: “O” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
Note 3: “—” indicates that the restricted substance corresponds to the exemption.

#5 Group of products: Other accessories that do not have an outstanding function
Mouse, keyboard, power supply, battery charger, wireless video module, video ingest module, wireless charger, cable kit

Restricted substances and their chemical symbols

Unit| (Pb)| (Hg)| (Cd)| (Cr+6)| (PBB)| (PBDE)
Circuit board| | O| O| O| O| O
Shell| O| O| O| O| O| O
Metal part| | O| O| O| O| O
Cable| _| O| O| O| O| O

Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition.
Note 2: “O” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
Note 3: “—” indicates that the restricted substance corresponds to the exemption.

#6 Group of products: Other printer products
Thermal receipt printer

Restricted substances and their chemical symbols

Unit| (Pb)| (Hg)| (Cd)| (Cr+6)| (PBB)| (PBDE)
Circuit board| | O| O| O| O| O
Shell| O| O| O| O| O| O
Metal part| | O| O| O| O| O
Print head| | O| O| O| O| O
Motor| | O| O| O| O| O
Paper roller| _| O| O| O| O| O

Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition.
Note 2: “O” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
Note 3: “—” indicates that the restricted substance corresponds to the exemption.

#7 Group of products: VR (Virtual reality products) monitors (including head-mounted monitors) / Retail Point of Sale monitors

Restricted substances and their chemical symbols

Unit| (Pb)| (Hg)| (Cd)| (Cr+6)| (PBB)| (PBDE)
Circuit board| | O| O| O| O| O
Shell| O| O| O| O| O| O
Metal part| | O| O| O| O| O
Lens| O| O| O| O| O| O
Input/output device| | O| O| O| O| O
Light-sensing component| | O| O| O| O| O
Cable| | O| O| O| O| O
Liquid Crystal Display
(LCD) Panel| | O| O| O| O| O

Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition.
Note 2: “©” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
Note 3: “—” indicates that the restricted substance corresponds to the exemption.

Information for European Union Commission Regulation
1275/2008

To locate product power consumption data, including when the product is in networked standby with all wired network ports connected and wireless devices connected, refer to section P14 “Additional information” of the product IT ECO Declaration at http://www.hp.com/hpinfo/globalcitizenship/environment/productdata /itecodesktop-pc.html.

Where applicable, activate and deactivate a wireless network using the instructions included in the product user guide or the operating system. Information is also available at http://www.hp.com/support.

© Copyright 2015-2022 HP Development Company, L.P.
Bluetooth is a trademark owned by its proprietor and used by HP Inc. under license. Java is a registered trademark of Oracle and/or its affiliates.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

References

• Anatel — Agência Nacional de Telecomunicações
• HP Planet Partners 助力循环经济发展 | 中国惠普
• Laptop Computers, Desktops, Printers, Ink & Toner | HP® Official Site
• Product Return and Recycling | HP® Official Site
• Hewlett-Packard Labor Condition Applications
• hp.com/hpinfo/globalcitizenship/
• Product Return and Recycling | HP® Official Site
• hp.com/support
• MT-Tech Cloud (EX)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>