HID iCLASS SE Connectivity Module Owner’s Manual
- June 11, 2024
- HID
Table of Contents
HID iCLASS SE Connectivity Module
Product Information
The product complies with Part 15 of the FCC Rules and contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). The device must not cause harmful interference and must accept any interference received. It meets the IC requirements for RF exposure in public or uncontrolled environments. The device is authorized for use in a mobile application only.
RF Exposure Considerations
The transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. At least 20 cm of separation distance between
the module and the user’s body must be maintained at all times.
Instruction to Module Integrator
A label must be affixed to the outside of the final commercial product
containing the FCC ID and IC information. The antenna gain of a new antenna
should be of the same type as the originally approved antenna and should not
be higher than the antenna gain of the originally tested antenna. The list of
originally approved PCB antennas is provided.
Additional Testing, Part 15 Subpart B Disclaimer
The final host/module combination may need to be evaluated against the FCC
Part 15B criteria for unintentional radiators to be properly authorized for
operation as a Part 15 digital device. The FCC Part 15 Statement shall be
included in the user manual of the final commercial product if applicable.
Product Usage Instructions
Make sure to maintain at least 20 cm of separation distance between the module and your body at all times. Do not operate the device in conjunction with any other antenna or transmitter. Affix the provided label containing FCC ID and IC information to the outside of the final commercial product. When using a new antenna, make sure it has the same type and antenna gain as the originally approved antenna. For additional testing, refer to the FCC Part 15 Statement in the user manual of the final commercial product.
HID® iCLASS® SE Connectivity Module Install Guide Addendum
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; (2) This device must accept any interference received, including interference that may cause undesired operation.
ISED
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions: (1) This device
may not cause interference; (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
Operation in the band 5150–5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems.
RF EXPOSURE CONSIDERATIONS
This module complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. RF Exposure – At least
20 cm of separation distance between the module and the user’s body must be
maintained at all times.
ISED
This device meets the IC requirements for RF exposure in public or
uncontrolled environments.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. RF Exposure – At least 20 cm of separation
distance between the module and the user’s body must be maintained at all
times.
INSTRUCTION TO MODULE INTEGRATOR
LABELING
A label must be affixed to the outside of final commercial product with the
following statements:
- Contains FCC ID: JQ6-SECONNECT
- Contains IC: 2236B-SECONNECT
ANTENNA
The antenna gain of a new antenna should be of the same type as the originally
approved antenna and the antenna gain should not be higher than the antenna
gain of the originally tested antenna. The list of originally approved PCB
antennas is the following:
- BLE – Type of antenna: chip SMD; WURTH P/N: 7488930245; peak gain: 0.5 dBi
- Wi-Fi – Type of antenna: chip SMD; AVX P/N: M830520; peak gain: 1.0 dBi (2.4 GHz); 2.6 dBi (5 GHz)
FCC RF EXPOSURE CONSIDERATIONS
Consistent with §2.909(a), the following text must be included within the
user’s manual or operator instruction guide for the final commercial product:
This modular complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. This device is only
authorized for use in a mobile application. At least 20 cm of separation
distance between the module and the user’s body must be maintained at all
times.
ADDITIONAL TESTING, PART 15 SUBPART B DISCLAIMER
The final host/module combination may also need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device. The FCC Part 15 Statement shall be included in the user manual of the final commercial product if applicable.
CAUTION STATEMENT FOR MODIFICATIONS:
CAUTION: Any changes or modifications not expressly approved could void
the user’s authority to operate the equipment.
611 Center Ridge Drive Austin, Texas 78753 USA
- FREE +1800 237 7769
- MAIN +1512 776 9000
- FAX +1 512 776 9630
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>