SUSSEX RBHS150RH Circa Wall Bath Hostess System Installation Guide
- June 12, 2024
- SUSSEX
Table of Contents
SUSSEX RBHS150RH Circa Wall Bath Hostess System
Product Information
- Product Name: Circa Wall Bath HostessSystem
- Product Code: RBHS150RH (150mm), RBHS200RH (200mm), RBHS250RH (250mm)
- Product Variants: RBHS150RH-V (150mm – Vertex), RBHS200RH-V (200mm – Vertex), RBHS250RH-V (250mm – Vertex)
- Standards Compliance: AS/NZS 3718:2005 LIC. 20081
- Recommended Water Pressure: 300-500 kpa
- Maximum Water Temperature: 65 deg.c
Product Usage Instructions
- Rough-In Plumbing (MASTERFIT) Mounting Guide:
- The Masterfit will be supplied with the Spindles pre-installed.
- Prepare a nogging and secure it 28-32mm back from the front of the wall stud, using the provided screws (x4). Refer to Figure 1 for guidance.
- The Masterfit (in-wall) will be marked “This side Up” to indicate orientation. Ensure the Masterfit is positioned correctly.
- Using the provided screws (x4), mount the Masterfit (in-wall) to the nogging.
- Ensure the Masterfit is level and square to the wall studs.
- Pipe Connections:
- Seal the wall around the Locking Sleeve and immediately fit the Dress Ring.
- Fit the Handle Body onto the Spindle, ensuring it is fully engaged. Refer to Figure 1B for guidance.
- Secure the Handle Body by tightening the Set screw using the provided 2mm Allen key. Tighten well.
- Fitting Off:
- After completing the installation, establish water supply.
- Check the function of the Tapware and ensure there are no water leaks.
Note: Tapware installation should be carriedout by a Licensed Plumber in
accordance with AS/NZS 3500:2003.
For more information, visit sussextaps.com.au
DIMENSION
Connections
Side View
Product code
- RBHS150RH Wall bath hostess syst 150mm
- RBHS200RH Wall bath hostess syst 200mm
- RBHS250RH Wall bath hostess syst 250mm
- RBHS150RH-V Wall bath hostess syst 150mm – Vertex
- RBHS200RH-V Wall bath hostess syst 200mm – Vertex
- RBHS250RH-V Wall bath hostess syst 250mm – Vertex
Rough in plumbing (MASTERFIT) mounting guide
- The Masterfit will be supplied with the Spindles preinstalled.
- Prepare a nogging and secure 28-32mm back from the front Using the screws (x4) of the stud (See Fig.1)
- The Masterfit (in-wall) will be marked “This side Up” to Ensure the Masterfit is indicate orientation.
- Using the screws (x4) provided, mount the Masterfit (in-wall) to the Nogging.
- Ensure the Masterfit is level and square to the Wall Studs.
Pipe connections
- The Masterfit is supplied with coloured thread Caps to protect and identify the Hot and Cold inlet connections.
- All lines must be free from any dirt and debris before connecting to the Masterfit. Flush all water feed lines.
- Connect Hot and Cold lines to the corresponding 1/2” BSP ports of the Masterfit. (See Fig.1A)
- Do not remove or disturb any factory fitted Pressure Plugs or Fixings.
- Once all water connections are made, use the “Spindle Handle Adapter” and check Hot/Cold water operation.
- Check all fittings and connections for leaks.
- Store the Dress Kit in a safe place until required for Fit off.
Fitting off
- Seal the wall around the Locking Sleeve and immediately fit the Dress Ring.
- Fit the Handle Body, the Handle Body must be fully engaged onto the Spindle; note the Set Screw contact point. (See Fig.1B)
- Secure the Handle body by tightening the Set screw using the 2mm Allen key provided. (Tighten well)
- After completing the installation, establish water supply, check function of Tapware and ensure no water leaks.
Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS
3500:2003 Recommended working water pressure 300-500 kpa. Maximum water
temperature is 65 deg.c
Copyright © Sussex Taps.
sussextaps.com.au
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>